DTC P219A Bank 1 Air-Fuel Ratio Imbalance |
| DTC No. | DTC Detection Condition | Trouble Area |
| P219A | One of the following conditions is met (2 trip detection logic):
|
|

| GTS Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P219A) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| DTC P219A is output | A |
| DTC P219A and other DTCs are output | B |
|
| ||||
| A | |
| 2.READ VALUE USING GTS (FREEZE FRAME DATA) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| DTC stored during idling | It is possible to conclude that the problem was detected due to a "lean imbalance" (detected using crankshaft speed variation). |
| DTC stored while vehicle being driven | It is possible to conclude that the problem was detected due to a "rich imbalance" (detected using the air fuel ratio sensor). |
| NEXT | |
| 3.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME) |
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Warm up the engine.
Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume / Cylinder #1 to #4 Misfire Count.
Perform the Control the Injection Volume operation with the engine idling.
Check the misfire counts ("Cylinder #1 Misfire Count" to "Cylinder #4 Misfire Count") while decreasing the injection volume in 5% increments.
| NEXT | |
| 4.CHECK FOR EXHAUST GAS LEAK |
Check for exhaust gas leaks.
|
| ||||
| OK | |
| 5.CHECK INTAKE SYSTEM |
Check the intake system for vacuum leaks (Click here).
|
| ||||
| OK | |
| 6.INSPECT SPARK PLUG |
Inspect the spark plug of the cylinder causing the imbalance .
|
| ||||
| OK | |
| 7.CHECK FOR SPARK (SPARK TEST) |
Perform a spark test .
| NEXT | |
| 8.CHECK CYLINDER COMPRESSION PRESSURE |
Measure the cylinder compression pressure of the misfiring cylinder .
|
| ||||
| OK | |
| 9.CHECK HARNESS AND CONNECTOR (POWER SOURCE VOLTAGE) |
![]() |
Disconnect the fuel injector assembly (for port injection) connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| C8-1 - Body ground | Ignition switch ON | 11 to 14 V |
| C30-1 - Body ground | Ignition switch ON | 11 to 14 V |
| C9-1 - Body ground | Ignition switch ON | 11 to 14 V |
| C31-1 - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector (to Fuel Injector Assembly) |
| *b | No. 1 cylinder |
| *c | No. 2 cylinder |
| *d | No. 3 cylinder |
| *e | No. 4 cylinder |
|
| ||||
| OK | |
| 10.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM) |
Check the harness and connector of fuel injector assembly (for port injection) .
Check the harness and connector of fuel injector assembly (for direct injection) .
|
| ||||
| OK | |
| 11.CHECK FUEL INJECTOR ASSEMBLY OF CYLINDER CAUSING IMBALANCE |
Check the fuel injector assembly (for port injection) [whether fuel volume is high or low, and whether injection pattern is poor] (Click here).
Check the fuel injector assembly (for direct injection) [whether fuel volume is high or low, and whether injection pattern is poor] (Click here).
| Result | Proceed to |
| OK | A |
| Fuel injector assembly (for port injection) is NG. | B |
| Fuel injector assembly (for direct injection) is NG. | C |
|
| ||||
|
| ||||
| A | |
| 12.CHECK FOR CAUSE OF FAILURE |
If the cause of the problem has not been found even after performing the troubleshooting procedure, perform the inspection below.
Check the intake valve for deposits.
| NEXT | |
| 13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Check for DTCs.
| NEXT | ||
| ||