Home › Engine / Hybrid System › FA20 (ENGINE CONTROL) › SFI SYSTEM
RM2090E _51 Engine / Hybrid System _060665 FA20 ENGINE CONTROL _0297470 SFI SYSTEM J

FA20 ENGINE CONTROL  SFI SYSTEM  Starter Signal Circuit  


DESCRIPTION

w/ Entry and Start System

While the engine is being cranked, the ECM detects the current from the ST relay drive circuit to the STSW2 and STA terminals, and carries out engine control when starting (STSW2 signal and STA signal). The ECM drives the ST relay until the engine start signal is input from the certification ECU (smart key ECU assembly), and drives the starter until a complete engine start is detected.


w/o Entry and Start System

While the engine is being cranked, the current from the ST relay flows to the ECM STSW2 terminal.


WIRING DIAGRAM

A280174E05
0.896,1.521 1.323,1.771 0.427,0.25 10 false D55 0.906,1.677 2.083,2.073 1.177,0.396 10 false Ignition or Starter Switch Assembly 0.365,0.833 1.115,1.177 0.75,0.344 10 false AM2 No.1 1.177,0.552 1.646,0.813 0.469,0.26 10 false AM2 5.469,0.802 5.792,1.083 0.323,0.281 10 false ST 0.875,2.542 1.323,2.813 0.448,0.271 10 false AM1 1.177,0.979 1.771,1.396 0.594,0.417 10 false AM1 0.563,4.792 1.146,5.167 0.583,0.375 10 false Battery 2.438,1.396 4.219,1.802 1.781,0.406 10 false Clutch Start Switch Assembly 2.448,1.229 2.781,1.438 0.333,0.208 10 false A20 2.875,2.906 3.771,3.396 0.896,0.49 10 false INHIBITOR 6.302,2.333 6.844,2.688 0.542,0.354 10 false ECM 3.469,3.271 3.823,3.479 0.354,0.208 10 false L2 3.469,3.427 5,4.156 1.531,0.729 10 false Park/Neutral Position Switch Assembly 4.49,1.448 4.813,1.865 0.323,0.417 10 false ST 5.833,1.104 6.188,1.385 0.354,0.281 10 false A35 5.833,0.677 6.26,1.052 0.427,0.375 10 false A33 5.885,0.917 6.198,1.229 0.313,0.313 10 false 26 5.885,0.49 6.177,0.792 0.292,0.302 10 false 17 2.323,1.01 2.646,1.323 0.323,0.313 10 false *1 2.292,1.896 2.479,2.083 0.188,0.188 10 false *2 3.813,0.99 4.229,1.313 0.417,0.323 10 false *1 4.094,1.844 4.438,2.115 0.344,0.271 10 false *2 4.26,2.427 4.604,2.75 0.344,0.323 10 false *2 2.104,4.948 4.052,5.302 1.948,0.354 10 false *1: for Manual Transmission 2.104,5.302 4.063,5.656 1.958,0.354 10 false *2: for Automatic Transmission 4.906,1.021 5.146,1.323 0.24,0.302 10 false 1 4.646,2.74 4.896,3 0.25,0.26 10 false 4 4.167,0.99 4.417,1.271 0.25,0.281 10 false 2 4.906,0.594 5.229,0.969 0.323,0.375 10 false 3 4.167,0.594 4.417,0.885 0.25,0.292 10 false 5 3.521,2.438 3.771,2.708 0.25,0.271 10 false 1 2.76,0.99 3.083,1.281 0.323,0.292 10 false 1 2.042,0.99 2.313,1.25 0.271,0.26 10 false 1 2.781,2.438 3.063,2.708 0.281,0.271 10 false 2 3.552,0.979 3.833,1.281 0.281,0.302 10 false 2 1,0.563 1.344,0.854 0.344,0.292 10 false 7 3.531,2 3.781,2.281 0.25,0.281 10 false 3 2.771,2 3.042,2.313 0.271,0.313 10 false 5 1.708,0.552 2.156,0.854 0.448,0.302 10 false ST2 1.729,0.979 2.083,1.229 0.354,0.25 10 false ST1 6.146,0.677 6.813,1.073 0.667,0.396 10 false STSW2 6.156,1.115 6.688,1.438 0.531,0.323 10 false STA 1,1 1.24,1.24 0.24,0.24 10 false 2 2.042,0.563 2.271,0.792 0.229,0.229 10 false 8 4.885,3.354 5.115,3.656 0.229,0.302 10 false 5 4.49,4.229 4.854,4.542 0.365,0.313 10 false B2 5.198,4.01 5.51,4.26 0.313,0.25 10 false B1 4.531,4.042 4.823,4.292 0.292,0.25 10 false 1 5.313,3.823 5.563,4.083 0.25,0.26 10 false 1 5.802,4.479 7.063,4.917 1.26,0.438 10 false Starter Assembly 0.365,3.688 0.896,4 0.531,0.313 10 false MAIN 0.885,3.688 1.396,4.021 0.51,0.333 10 false ALT 0.094,0.073 2.26,0.313 2.167,0.24 12 false w/o Entry and Start System:

A280173E02
4.896,3.333 5.26,3.646 0.365,0.313 10 false ST 4.99,2.792 5.333,3.104 0.344,0.313 10 false ST 4.25,4.885 4.938,5.344 0.688,0.458 10 false ST CUT 3.125,2.927 3.917,3.302 0.792,0.375 10 false INHIBITOR 3.01,4.031 3.906,4.417 0.896,0.385 10 false PUSH-AT 5.99,5.865 6.417,6.115 0.427,0.25 10 false ECM 0.458,4.573 1.271,5.021 0.813,0.448 10 false AM2 NO.1 0.458,5.219 1.188,5.625 0.729,0.406 10 false IG2 MAIN 0.667,6.375 1.281,6.708 0.615,0.333 10 false Battery 0.49,3.813 1.302,4.156 0.813,0.344 10 false AM2 NO.2 0.51,2.594 1.719,2.927 1.208,0.333 10 false Clutch Start Switch Assembly 0.521,2.427 1,2.75 0.479,0.323 10 false A20 0.542,1.063 0.938,1.385 0.396,0.323 10 false L2 0.542,1.24 1.885,1.667 1.344,0.427 10 false Park/Neutral Position Switch Assembly 5.177,1.427 5.594,1.719 0.417,0.292 10 false D48 5.177,1.594 7.052,2.063 1.875,0.469 10 false Certification ECU (Smart Key ECU Assembly) 5.344,2.667 5.75,3 0.406,0.333 10 false A33 5.385,2.479 5.646,2.698 0.26,0.219 10 false 14 5.344,3.917 5.729,4.24 0.385,0.323 10 false A35 5.354,4.615 5.802,4.969 0.448,0.354 10 false A35 5.385,3.729 5.698,3.99 0.313,0.26 10 false 26 5.396,4.417 5.729,4.688 0.333,0.271 10 false 34 4.74,3.708 4.969,4.042 0.229,0.333 10 false 1 4.5,3.708 4.729,3.969 0.229,0.26 10 false 5 4.51,2.969 4.656,3.115 0.146,0.146 10 false 3 4.75,2.969 4.844,3.135 0.094,0.167 10 false 2 2.958,3.281 3.219,3.552 0.26,0.271 10 false 5 2.667,3.281 2.958,3.542 0.292,0.26 10 false 2 1.281,2.073 1.51,2.344 0.229,0.271 10 false 2 2.958,2.51 3.188,2.75 0.229,0.24 10 false 3 2.656,2.521 2.917,2.74 0.26,0.219 10 false 1 5.719,2.677 6.406,3.052 0.688,0.375 10 false STSW2 5.719,3.917 6.208,4.25 0.49,0.333 10 false STA 5.719,4.625 6.302,5.01 0.583,0.385 10 false STAR 4.083,4.333 4.385,4.625 0.302,0.292 10 false 3 4.083,4.521 4.396,4.854 0.313,0.333 10 false 2 4.5,4.115 4.771,4.406 0.271,0.292 10 false 4 4.813,4.51 5.073,4.781 0.26,0.271 10 false 1 3.094,4.917 3.531,5.25 0.438,0.333 10 false IGS 3.563,4.573 3.802,4.833 0.24,0.26 10 false 2 2.813,4.323 3.042,4.583 0.229,0.26 10 false 5 2.823,4.573 3.104,4.802 0.281,0.229 10 false 1 3.563,4.323 3.854,4.615 0.292,0.292 10 false 3 1.552,5.625 2.052,6.052 0.5,0.427 10 false IG2 2.417,4.802 2.896,5.104 0.479,0.302 10 false IG2 2.021,5.26 2.281,5.625 0.26,0.365 10 false 2 1.271,4.99 1.563,5.281 0.292,0.292 10 false 5 1.271,5.26 1.563,5.552 0.292,0.292 10 false 1 2.021,4.979 2.24,5.25 0.219,0.271 10 false 3 1.552,7.083 3.531,7.417 1.979,0.333 10 false *1: for Manual Transmission 1.552,7.438 3.552,7.771 2,0.333 10 false *2: for Automatic Transmission 4.781,1.677 5.177,2.01 0.396,0.333 10 false *1 2.667,3.594 2.979,3.906 0.313,0.313 10 false *2 2.979,2.323 3.323,2.635 0.344,0.313 10 false *2 4.167,2.344 4.354,2.531 0.188,0.188 10 false *2 5.51,0.677 5.781,0.958 0.271,0.281 10 false 9 5.51,0.281 5.844,0.573 0.333,0.292 10 false 5 1.198,0.458 1.469,0.729 0.271,0.271 10 false 4 0.521,2.073 0.76,2.344 0.24,0.271 10 false 1 0.583,0.74 0.885,1.042 0.302,0.302 10 false 5 5.354,5.073 5.719,5.365 0.365,0.292 10 false A33 5.396,4.885 5.719,5.177 0.323,0.292 10 false 27 2.833,5.896 3.135,6.167 0.302,0.271 10 false B2 3.552,5.677 3.896,5.938 0.344,0.26 10 false B1 2.885,5.719 3.188,5.99 0.302,0.271 10 false 1 3.688,5.49 3.99,5.781 0.302,0.292 10 false 1 4.146,6.156 5.271,6.417 1.125,0.26 10 false Starter Assembly 5.729,5.083 6.24,5.427 0.51,0.344 10 false IGSW 5.469,1.052 5.854,1.396 0.385,0.344 10 false 10 0.531,5.646 0.948,5.927 0.417,0.281 10 false MAIN 5.688,0.365 6.219,0.698 0.531,0.333 10 false NSW 5.677,0.771 6.271,1.115 0.594,0.344 10 false IG2D 5.688,1.135 6.188,1.438 0.5,0.302 10 false CLUT 0.073,0.063 2.063,0.292 1.99,0.229 12 false w/ Entry and Start System: 1.646,2.073 2.042,2.406 0.396,0.333 10 false *1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK WHETHER ENGINE CAN BE CRANKED
a.

Check if the engine can be cranked.

Result
Result Proceed to
Engine cannot be cranked A
Engine can be cranked (w/ Entry and Start System) B
Engine can be cranked (w/o Entry and Start System) C



A

2.READ VALUE USING GTS (STARTER SIGNAL)

B

19.READ VALUE USING GTS (STARTER SIGNAL)

C

34.READ VALUE USING GTS (ST SIGNAL)
2.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Starter Signal.


e.

Check the value displayed on the GTS when the ignition switch is turned to the ON and START positions.

OK
Ignition Switch Position Starter Signal
ON Close (OFF)
START Open (ON)

Result
Result Proceed to
OK (w/ Entry and Start System) A
NG (w/ Entry and Start System) B
OK (w/o Entry and Start System) C
NG (w/o Entry and Start System) D



A

3.CHECK HARNESS AND CONNECTOR (ST RELAY - ECM - STARTER ASSEMBLY)

B

4.READ VALUE USING GTS (STARTER CUT RELAY)

C

21.CHECK HARNESS AND CONNECTOR (ECM - ST RELAY - STARTER ASSEMBLY)

D

22.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
3.CHECK HARNESS AND CONNECTOR (ST RELAY - ECM - STARTER ASSEMBLY)
a.

Disconnect the ECM connector.


b.

Remove the ST relay from the engine room relay block assembly.


c.

Disconnect the starter assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
A33-14 (STSW2) - B1-1 Always Below 1 Ω
ST relay terminal 3 - B1-1 Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
A33-14 (STSW2), B1-1 or ST relay terminal 3 - Body ground Always 10 kΩ or higher




OK

4.READ VALUE USING GTS (STARTER CUT RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING GTS (STARTER CUT RELAY)
a.

Connect the GTS to DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Starter Cut Relay.


e.

Check the value displayed on the GTS when the ignition switch is turned to the ON and START positions.

OK
Ignition Switch Position Starter Cut Relay
ON OFF
START ON

Result
Result Proceed to
NG A
OK (for automatic transmission models) B
OK (for manual transmission models) C



A

5.CHECK HARNESS AND CONNECTOR (ECM - ST CUT RELAY)

B

9.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

C

14.INSPECT CLUTCH START SWITCH ASSEMBLY
5.CHECK HARNESS AND CONNECTOR (ECM - ST CUT RELAY)
a.

Disconnect the ECM connector.


b.

Remove the ST CUT relay from the engine room relay block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
A35-34 (STAR) - ST CUT relay terminal 1 Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
A35-34 (STAR) or ST CUT relay terminal 1 - Body ground Always 10 kΩ or higher




OK

6.CHECK HARNESS AND CONNECTOR (IGS RELAY - ST CUT RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (IGS RELAY - ST CUT RELAY - BODY GROUND)
a.

Remove the ST CUT relay and IGS relay from the engine room relay block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
ST CUT relay terminal 3 - IGS relay terminal 3 Always Below 1 Ω
ST CUT relay terminal 2 - IGS relay terminal 3 Always Below 1 Ω
IGS relay terminal 2 - Body ground Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
ST CUT relay terminal 3, ST CUT relay terminal 2 or IGS relay terminal 3 - Body ground Always 10 kΩ or higher




OK

7.INSPECT TERMINAL VOLTAGE (IGS RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT TERMINAL VOLTAGE (IGS RELAY)
a.
A280168E01
0.171,0.422 0.333,0.608 0.163,0.186 10 *1 0.462,3.277 0.654,3.447 0.192,0.169 10 *2

Remove the IGS relay from the engine room relay block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
IGS relay terminal 5 - Body ground Always 11 to 14 V


Text in Illustration
*1 Engine Room Relay Block Assembly
*2 IGS Relay Terminal



OK

8.CHECK HARNESS AND CONNECTOR (ECM - IG2 RELAY - IGS RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (ECM - IG2 RELAY - IGS RELAY)
a.

Disconnect the ECM connector.


b.

Remove the IG2 relay and IGS relay from the engine room relay block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
A33-27 (IGSW) - IG2 relay terminal 3 Always Below 1 Ω
IG2 relay terminal 3 - IGS relay terminal 1 Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
A33-27 (IGSW), IG2 relay terminal 3 or IGS relay terminal 1 - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Inspect the park/neutral position switch assembly (See page Drivetrain>TX6A (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>INSPECTION).



OK

10.CHECK HARNESS AND CONNECTOR (SMART KEY ECU - PARK/NEUTRAL POSITION SWITCH)

NG

10.CHECK HARNESS AND CONNECTOR (SMART KEY ECU - PARK/NEUTRAL POSITION SWITCH)
a.

Disconnect the park/neutral position switch assembly connector.


b.

Disconnect the smart key ECU assembly connector.


c.

Remove the INHIBITOR relay from the engine room relay block assembly.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
L2-4 - D48-5 (NSW) Always Below 1 Ω
L2-4 - INHIBITOR relay terminal 1 Always Below 1 Ω
L2-5 - Body ground Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
L2-4, D48-5 (NSW) or INHIBITOR relay terminal 1 - Body ground Always 10 kΩ or higher




OK

11.CHECK HARNESS AND CONNECTOR (ST CUT RELAY - INHIBITOR RELAY - ST RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (ST CUT RELAY - INHIBITOR RELAY - ST RELAY)
a.

Remove the ST relay, ST CUT relay and INHIBITOR relay from the engine room relay block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
ST CUT relay terminal 4 - INHIBITOR relay terminal 2 Always Below 1 Ω
ST CUT relay terminal 4 - INHIBITOR relay terminal 5 Always Below 1 Ω
ST CUT relay terminal 4 - ST relay terminal 5 Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
ST CUT relay terminal 4, INHIBITOR relay terminal 2, INHIBITOR relay terminal 5 or ST relay terminal 5 - Body ground Always 10 kΩ or higher




OK

12.CHECK HARNESS AND CONNECTOR (INHIBITOR RELAY - ST RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (INHIBITOR RELAY - ST RELAY)
a.

Remove the ST relay and INHIBITOR relay from the engine room relay block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
INHIBITOR relay terminal 3 - ST relay terminal 2 Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
INHIBITOR relay terminal 3 or ST relay terminal 2 - Body ground Always 10 kΩ or higher




OK

13.CHECK HARNESS AND CONNECTOR (ECM - ST RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (ECM - ST RELAY)
a.

Disconnect the ECM connector.


b.

Remove the ST relay from the engine room relay block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
A35-26 (STA) - ST relay terminal 1 Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
A35-26 (STA) or ST relay terminal 1 - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.INSPECT CLUTCH START SWITCH ASSEMBLY
a.

Inspect the clutch start switch assembly (for LHD) (See page Drivetrain>CLUTCH>CLUTCH PEDAL SWITCH(for LHD)>INSPECTION).


b.

Inspect the clutch start switch assembly (for RHD) (See page Drivetrain>CLUTCH>CLUTCH PEDAL SWITCH(for RHD)>INSPECTION).


Result
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C


A

15.INSPECT TERMINAL VOLTAGE (+B OF CLUTCH START SWITCH ASSEMBLY)

B

REPLACE CLUTCH START SWITCH ASSEMBLY

C

REPLACE CLUTCH START SWITCH ASSEMBLY

15.INSPECT TERMINAL VOLTAGE (+B OF CLUTCH START SWITCH ASSEMBLY)
a.
U190114E02
1.49,0.354 1.781,0.51 0.292,0.156 10 false A20 0.24,0.115 0.531,0.271 0.292,0.156 10 false *a

Disconnect the clutch start switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A20-1 - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Clutch Start Switch Assembly)



OK

16.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH - ST RELAY - SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH - ST RELAY - SMART KEY ECU ASSEMBLY)
a.

Disconnect the clutch start switch assembly connector.


b.

Remove the ST relay from the engine room relay block assembly.


c.

Disconnect the smart key ECU assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A20-2 - ST relay terminal 2 Always Below 1 Ω
A20-2 - D48-10 (CLUT) Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
A20-2, D48-10 (CLUT), or ST relay terminal 2 - Body ground Always 10 kΩ or higher




OK

17.CHECK HARNESS AND CONNECTOR (ST RELAY - ST CUT RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK HARNESS AND CONNECTOR (ST RELAY - ST CUT RELAY)
a.

Remove the ST relay and ST CUT relay from the engine room relay block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
ST relay terminal 5 - ST CUT relay terminal 4 Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
ST relay terminal 5 or ST CUT relay terminal 4 - Body ground Always 10 kΩ or higher




OK

18.CHECK HARNESS AND CONNECTOR (ECM - ST RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK HARNESS AND CONNECTOR (ECM - ST RELAY)
a.

Disconnect the ECM connector.


b.

Remove the ST relay from the engine room relay block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
A35-26 (STA) - ST relay terminal 1 Always Below 1 Ω
A33-14 (STSW2) - ST relay terminal 3 Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
A35-26 (STA), A33-14 (STSW2), ST relay terminal 1 or ST relay terminal 3 - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Starter Signal.


e.

Check the value displayed on the GTS when the ignition switch is turned to the ON and START positions.

OK
Ignition Switch Position Starter Signal
ON Close (OFF)
START Open (ON)

Result
Result Proceed to
NG A
OK B



A

20.CHECK HARNESS AND CONNECTOR (ECM - ST RELAY)

B

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

20.CHECK HARNESS AND CONNECTOR (ECM - ST RELAY)
a.

Disconnect the ECM connector.


b.

Remove the ST relay from the engine room relay block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
A35-26 (STA) - ST relay terminal 1 Always Below 1 Ω
A33-14 (STSW2) - ST relay terminal 3 Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
A35-26 (STA), A33-14 (STSW2), ST relay terminal 1 or ST relay terminal 3 - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.CHECK HARNESS AND CONNECTOR (ECM - ST RELAY - STARTER ASSEMBLY)
a.

Disconnect the ECM connector.


b.

Disconnect the starter assembly connector.


c.

Remove the ST relay from the engine room relay block assembly.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
B1-1 - A33-17 (STSW2) Always Below 1 Ω
B1-1 - ST relay terminal 3 Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
A33-17 (STSW2), ST relay terminal 3 or B1-1 - Body ground Always 10 kΩ or higher




OK

22.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

22.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
a.

Inspect the ignition or starter switch assembly (See page Engine / Hybrid System>FA20 STARTING>IGNITION SWITCH>INSPECTION).



OK

23.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - ST RELAY)

NG

REPLACE IGNITION OR STARTER SWITCH ASSEMBLY

23.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - ST RELAY)
a.

Disconnect the ignition or starter switch assembly connector.


b.

Remove the ST relay from the engine room relay block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
D55-8 (ST2) - ST relay terminal 5 Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
D55-8 (ST2) or ST relay terminal 5 - Body ground Always 10 kΩ or higher




OK

24.INSPECT TERMINAL VOLTAGE (+B OF IGNITION OR STARTER SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

24.INSPECT TERMINAL VOLTAGE (+B OF IGNITION OR STARTER SWITCH ASSEMBLY)
a.
U146764E03
2,1.417 2.396,1.802 true 1.615,1.177 1.333,1.719 true 1.667,0.417 1.958,0.573 0.292,0.156 10 false D55 1.219,1.76 1.823,2 0.604,0.24 10 false 2(AM1) 2.427,1.823 3.031,2.063 0.604,0.24 10 false 7(AM2) 0.094,0.094 0.427,0.354 0.333,0.26 10 false *a

Disconnect the ignition or starter switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D55-2 (AM1) - Body ground Always 11 to 14 V
D55-7 (AM2) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Ignition or Starter Switch Assembly)

Result
Result Proceed to
NG A
OK (for Automatic Transmission) B
OK (for Manual Transmission) C



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

25.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

C

30.INSPECT CLUTCH START SWITCH ASSEMBLY
25.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Inspect the park/neutral position switch assembly (See page Drivetrain>TX6A (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>INSPECTION).



OK

26.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - INHIBITOR RELAY)

NG

26.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - INHIBITOR RELAY)
a.

Disconnect the park/neutral position switch assembly connector.


b.

Remove the INHIBITOR relay from the engine room relay block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
L2-4 - INHIBITOR relay terminal 1 Always Below 1 Ω
L2-5 - Body ground Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
L2-4 or INHIBITOR relay terminal 1 - Body ground Always 10 kΩ or higher




OK

27.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - INHIBITOR RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

27.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - INHIBITOR RELAY)
a.

Disconnect the ignition or starter switch assembly connector.


b.

Remove the INHIBITOR relay from the engine room relay block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
D55-1 (ST1) - INHIBITOR relay terminal 5 Always Below 1 Ω
D55-1 (ST1) - INHIBITOR relay terminal 2 Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
D55-1 (ST1), INHIBITOR relay terminal 2 or INHIBITOR relay terminal 5 - Body ground Always 10 kΩ or higher




OK

28.CHECK HARNESS AND CONNECTOR (INHIBITOR RELAY - ST RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

28.CHECK HARNESS AND CONNECTOR (INHIBITOR RELAY - ST RELAY)
a.

Remove the INHIBITOR relay and ST relay from the engine room relay block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
INHIBITOR relay terminal 3 - ST relay terminal 2 Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
INHIBITOR relay terminal 3 or ST relay terminal 2 - Body ground Always 10 kΩ or higher




OK

29.CHECK HARNESS AND CONNECTOR (ECM - ST RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

29.CHECK HARNESS AND CONNECTOR (ECM - ST RELAY)
a.

Disconnect the ECM connector.


b.

Remove the ST relay from the engine room relay block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
A35-26 (STA) - ST relay terminal 1 Always Below 1 Ω
A33-17 (STSW2) - ST relay terminal 3 Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
A35-26 (STA), A33-17 (STSW2), ST relay terminal 1 or ST relay terminal 3 - Body ground Always 10 kΩ or higher




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

30.INSPECT CLUTCH START SWITCH ASSEMBLY
a.

Inspect the clutch start switch assembly (for LHD) (See page Drivetrain>CLUTCH>CLUTCH PEDAL SWITCH(for LHD)>INSPECTION).


b.

Inspect the clutch start switch assembly (for RHD) (See page Drivetrain>CLUTCH>CLUTCH PEDAL SWITCH(for RHD)>INSPECTION).


Result
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C


A

31.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - CLUTCH START SWITCH)

B

REPLACE CLUTCH START SWITCH ASSEMBLY

C

REPLACE CLUTCH START SWITCH ASSEMBLY

31.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - CLUTCH START SWITCH)
a.

Disconnect the ignition or starter switch assembly connector.


b.

Disconnect the clutch start switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
D55-1 (ST1) - A20-1 Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
D55-1 (ST1) or A20-1 - Body ground Always 10 kΩ or higher




OK

32.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH - ST RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

32.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH - ST RELAY)
a.

Disconnect the clutch start switch assembly connector.


b.

Remove the ST relay from the engine room relay block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
A20-2 - ST relay terminal 2 Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
A20-2 or ST relay terminal 2 - Body ground Always 10 kΩ or higher




OK

33.CHECK HARNESS AND CONNECTOR (ECM - ST RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

33.CHECK HARNESS AND CONNECTOR (ECM - ST RELAY)
a.

Disconnect the ECM connector.


b.

Remove the ST relay from the engine room relay block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
A35-26 (STA) - ST relay terminal 1 Always Below 1 Ω
A33-17 (STSW2) - ST relay terminal 3 Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
A35-26 (STA), A33-17 (STSW2), ST relay terminal 1 or ST relay terminal 3 - Body ground Always 10 kΩ or higher




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

34.READ VALUE USING GTS (ST SIGNAL)
a.

Connect the GTS to DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Starter Signal.


e.

Check the value displayed on the GTS when the ignition switch is turned to the ON and START positions.

OK
Ignition Switch Position Starter Signal
ON Close (OFF)
START Open (ON)

Result
Result Proceed to
NG A
OK B



A

35.CHECK HARNESS AND CONNECTOR (ECM - ST RELAY)

B

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

35.CHECK HARNESS AND CONNECTOR (ECM - ST RELAY)
a.

Disconnect the ECM connector.


b.

Remove the ST relay from the engine room relay block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
A35-26 (STA) - ST relay terminal 1 Always Below 1 Ω
A33-17 (STSW2) - ST relay terminal 3 Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
A35-26 (STA), A33-17 (STSW2), ST relay terminal 1 or ST relay terminal 3 - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR