Home › Engine / Hybrid System › FA20 (ENGINE CONTROL) › SFI SYSTEM
RM2090E _51 Engine / Hybrid System _060665 FA20 ENGINE CONTROL _0297470 SFI SYSTEM C

FA20 ENGINE CONTROL  SFI SYSTEM  P0441  Evaporative Emission Control System Incorrect Purge Flow  


DTC SUMMARY

DTC No. Monitoring Item Malfunction Detection Condition Trouble Area Detection Timing Detection Logic
P0441 Purge flow While engine running, following conditions successively met:
·

The pressure difference between non-purge and purge is less than threshold for 26 seconds or more.

·

Regardless of forced vent valve on (close) and purge being carried out, the pressure difference between non-purge and purge is less than threshold for 21 seconds or more.


·

Purge valve

·

Purge line

·

Connector/wire harness (Purge valve - ECM)

·

ECM

·

Leak from EVAP system


While engine running 2 trip

DESCRIPTION

The description can be found in EVAP (Evaporative Emission) System (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>EVAP System).

MONITOR DESCRIPTION

The purge flow monitor runs while the engine is running. The purge flow monitor consists of 2 monitors. The 1st monitor is conducted every time and the 2nd monitor is activated if necessary.

·

The 1st monitor

While the engine is running and the purge valve is on (open), the ECM monitors the purge flow by measuring the EVAP pressure change. If the variation in the pressure is less than threshold, the ECM begins the 2nd monitor.

A282471E03
0.031,1.688 1.021,2.094 0.99,0.406 10 false EVAP Pressure 0.271,0.667 1.083,1.073 0.813,0.406 10 false Purge valve 0.063,2.729 1.052,3.167 0.99,0.438 10 false Time (seconds) 0.146,0.104 2.458,0.563 2.313,0.458 10 false EVAP Pressure During 1st Monitor: 6.781,2.167 7.031,2.479 0.25,0.313 10 false OK 5.583,2.167 5.833,2.479 0.25,0.313 10 false OK 4.135,3.229 4.958,3.542 0.823,0.313 10 false Malfunction 6.156,1.208 6.979,1.521 0.823,0.313 10 false Malfunction 2.719,2.479 3.417,2.802 0.698,0.323 10 false Threshold 1.688,1.75 2.385,2.073 0.698,0.323 10 false Threshold

·

The 2nd monitor

The vent valve is turned on (closed) and the EVAP pressure is then measured. If the variation in the pressure is more than threshold, the ECM interprets this as the purge valve being stuck closed, and illuminates the MIL and stores DTC P0441 (2 trip detection logic).

A282472E02
3.917,2.677 4.698,3 0.781,0.323 10 false Malfunction 5.771,3.552 6.052,3.885 0.281,0.333 10 false OK 0.51,3.823 1.198,4.229 0.688,0.406 10 false Threshold 0.167,2.24 1.156,2.573 0.99,0.333 10 false EVAP Pressure 0.469,1.875 1.177,2.208 0.708,0.333 10 false Vent Valve 0.396,0.979 1.188,1.313 0.792,0.333 10 false Purge Valve 2.219,0.948 3.083,1.323 0.865,0.375 10 false Monitoring 1.542,1.094 1.813,1.406 0.271,0.313 10 false ON 1.885,1.458 2.292,1.771 0.406,0.313 10 false OFF 2.302,2 3.083,2.313 0.781,0.313 10 false OFF(Close) 3.177,1.635 3.958,1.948 0.781,0.313 10 false ON(Open) 0.104,0.094 2.458,0.583 2.354,0.49 10 false EVAP Pressure During 2nd Monitor:


CONFIRMATION DRIVING PATTERN

A285189E02
0.313,0.219 1.292,0.594 0.979,0.375 10 false Vehicle Speed 0.135,0.698 1.281,1.073 1.146,0.375 10 false 60 km/h (40 mph) 0.281,1.708 1.281,2.083 1,0.375 10 false 0 km/h (0 mph) 2.917,2.344 4.219,2.698 1.302,0.354 10 false 10 minutes or more 3.271,0.49 3.49,0.677 0.219,0.188 10 false [A]

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC procedure) (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine.

7.

Drive the vehicle at 60 km/h (40 mph) or more for 10 minute or more [A].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


8.

Enter the following menus: Powertrain / Engine / Trouble Codes.

9.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine / Utility / All readiness.

11.

Input the DTC: P0441.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.



13.

If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR EVAP CONTROL)
a.

Connect a GTS to the DLC3.


A280659E02
0.458,1.708 0.823,1.906 0.365,0.198 10 false *a 2.135,1.708 2.5,1.906 0.365,0.198 10 false *b 1.448,0.385 1.698,0.583 0.25,0.198 10 false F 1.563,0.698 1.813,0.896 0.25,0.198 10 false E 3.073,0.375 3.323,0.573 0.25,0.198 10 false F 3.167,0.667 3.354,0.865 0.188,0.198 10 false E

b.

Disconnect the vacuum hose (canister side) from the purge valve.


c.

Start the engine.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Active Test / Activate the VSV for EVAP Control.


f.

When the purge valve is operated using the GTS, check whether the port of the purge valve applies suction to your finger.


OK:
Tester Operation Tester Operation
VSV ON Purge valve port applies suction to finger
VSV OFF Purge valve port applies no suction to finger


Text in Illustration
*a Purge valve ON
*b Purge valve OFF


OK

2.INSPECT EVAP LEAK PART

NG

3.REPLACE PURGE VALVE
2.INSPECT EVAP LEAK PART
a.

Check for leakage from EVAP system (hose, disconnection, cracks, etc.).


OK:

No leakages in the EVAP purge line



OK

5.CHECK DTC OUTPUT (EVAP SYSTEM)

NG

4.REPAIR OR REPLACE EVAP PURGE LINE
3.REPLACE PURGE VALVE

NEXT

5.CHECK DTC OUTPUT (EVAP SYSTEM)
4.REPAIR OR REPLACE EVAP PURGE LINE

NEXT

5.CHECK DTC OUTPUT (EVAP SYSTEM)
5.CHECK DTC OUTPUT (EVAP SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Enter the following menus: Powertrain / Engine / Trouble Codes.


Result
Result Proceed to
EVAP system DTCs are output A
No DTCs output
(No pending DTCs output)
B


A

6.REPLACE ECM

B

END

6.REPLACE ECM

NEXT

7.CHECK DTC OUTPUT (EVAP SYSTEM)
7.CHECK DTC OUTPUT (EVAP SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Enter the following menus: Powertrain / Engine / Trouble Codes.


HINT:

If no pending DTCs are found, the repair has been successfully completed.



NEXT

END