Home › Engine / Hybrid System › FA20 (ENGINE CONTROL) › SFI SYSTEM › from 2016.06
RM2090E _51 Engine / Hybrid System _060665 FA20 ENGINE CONTROL _0297470 SFI SYSTEM J

FA20 ENGINE CONTROL  SFI SYSTEM  MIL Circuit  


DESCRIPTION

The Malfunction Indicator Light (MIL) is used to indicate vehicle malfunctions detected by the ECM.

The MIL operation can be checked visually. When the ignition switch is turned to ON, the MIL should be illuminated and should then turn off after engine is started. If the MIL remains illuminated or is not illuminated, conduct the following troubleshooting procedure using the GTS.

WIRING DIAGRAM

A397709E02
2.563,0.74 2.719,0.938 0.156,0.198 10 false 6 2.552,1.438 2.708,1.635 0.156,0.198 10 false 7 4.5,1.417 4.656,1.615 0.156,0.198 10 false 18 4.5,0.74 4.656,0.938 0.156,0.198 10 false 19 4.76,0.875 5.177,1.063 0.417,0.188 10 false CANH 4.781,1.573 5.198,1.76 0.417,0.188 10 false CANL 0.76,2.135 1.021,2.323 0.26,0.188 10 false D7 0.76,2.313 2.75,2.552 1.99,0.24 10 false Combination Meter Assembly 1.01,3.406 3,3.646 1.99,0.24 10 false : CAN Communication Line 4.771,2.146 5.188,2.333 0.417,0.188 10 false A33 4.771,2.333 5.396,2.594 0.625,0.26 10 false ECM 2.01,0.917 2.427,1.104 0.417,0.188 10 false CANH 2.052,1.615 2.469,1.802 0.417,0.188 10 false CANL

PROCEDURE

1.CHECK THAT MIL IS ILLUMINATED
a.

Perform troubleshooting in accordance with the table below.

Result
Result Condition Proceed to
MIL ON → MIL OFF Ignition switch ON → Engine is started A
Other than the above - B



A

B

2.CHECK CONNECTION BETWEEN GTS AND ECM
2.CHECK CONNECTION BETWEEN GTS AND ECM
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Checking the Data List for "Engine" is possible.

Result
Result Proceed to
Communication is possible A
Communication is not possible B



A

3.CHECK WHETHER DTC OUTPUT RECURS

B

3.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: System Select / Health Check.


e.

Check if any DTCs have been detected. Note down any DTCs.

Result
Result Proceed to
DTCs are not output A
DTCs are output B



A

4.PERFORM ACTIVE TEST USING GTS (CHECK MIL)

B

REPAIR CIRCUITS INDICATED BY OUTPUT

4.PERFORM ACTIVE TEST USING GTS (CHECK MIL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test / Check Engine Warning


e.

Check the status of the MIL while performing the Active Test.

Result
Result Proceed to
Changes A
Does not change B



A

B

REPLACE COMBINATION METER ASSEMBLY