The ECM constantly generates 5 V power from the battery voltages supplied to the +B terminal and +B2 terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.
When the VC circuit is short-circuited, the sensors that are supplied with power through the VC circuit are deactivated because the power is not supplied from the VC circuit.
ECM Power Source Circuit (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>ECM Power Source Circuit)
VC Output Circuit
Inspect the fuses for circuits related to this system before performing the following procedure.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Check for communication between the GTS and ECM.
Checking the Data List for "Engine" is possible.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A34-6 (+B) - A36-4 (E01) | Ignition switch ON | 11 to 14 V |
| A33-1 (+B2) - A36-4 (E01) | Ignition switch ON | 11 to 14 V |
If the result is not as specified, the system may not be activated due to no power supply to the ECM terminals +B and +B2.
OK
NG
Disconnect the throttle with motor body assembly connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
Checking the Data List for "Engine" is possible.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Disconnect the manifold absolute pressure sensor connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
Checking the Data List for "Engine" is possible.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Disconnect the fuel pressure sensor connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
Checking the Data List for "Engine" is possible.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Disconnect the crankshaft position sensor connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
Checking the Data List for "Engine" is possible.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Disconnect the accelerator pedal sensor assembly connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
Checking the Data List for "Engine" is possible.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Disconnect the battery current sensor assembly connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
Checking the Data List for "Engine" is possible.
| Result | Proceed to |
|---|---|
| Communication is not possible (w/ EVAP System) | A |
| Communication is not possible (w/o EVAP System) | B |
| Communication is possible | C |
A
B
C
Disconnect the canister pump module connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
Checking the Data List for "Engine" is possible.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Disconnect the throttle with motor body assembly connector.
Disconnect the manifold absolute pressure sensor connector.
Disconnect the fuel pressure sensor connector.
Disconnect the crankshaft position sensor connector.
Disconnect the accelerator pedal sensor assembly connector.
Disconnect the battery current sensor assembly connector.
Disconnect the canister pump module connector.*
*: w/ EVAP System
Disconnect the ECM connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A36-19 (VC) - Body ground | Always | 10 kΩ or higher |
| A35-22 (VCP2) - Body ground | Always | 10 kΩ or higher |
| A35-21 (VCPA) - Body ground | Always | 10 kΩ or higher |
OK
NG