Home › Engine / Hybrid System › FA20 (ENGINE CONTROL) › SFI SYSTEM
RM2090E _51 Engine / Hybrid System _060665 FA20 ENGINE CONTROL _0297470 SFI SYSTEM C

FA20 ENGINE CONTROL  SFI SYSTEM  P0327  Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor)  P0328  Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor)  P0332  Knock Sensor 2 Circuit Low Input (Bank 2)  P0333  Knock Sensor 2 Circuit High Input (Bank 2)  


DESCRIPTION

A flat-type knock sensor (non-resonant type) has a structure that can detect vibrations between approximately 5 kHz and 15 kHz.

Knock sensor is fitted onto the engine block to detect engine knocking.

The knock sensor contains a piezoelectric element which generates a voltage when it becomes deformed.

The voltage is generated when the engine block vibrates due to knocking. Any occurrence of engine knocking can be suppressed by delaying the ignition timing.

DTC No. DTC Detection Condition Trouble Area
P0327 Knock sensor voltage is less than 0.154 V for 1 second or more (bank 1).
(1 trip detection logic)
·

Open or short in knock sensor circuit (bank 1)

·

Knock sensor (bank 1)

·

ECM


P0328 Knock sensor voltage is more than 4.838 V for 1 second or more (bank 1).
(1 trip detection logic)
P0332 Knock sensor voltage is less than 0.154 V for 1 second or more (bank 2).
(1 trip detection logic)
·

Open or short in knock sensor circuit (bank 2)

·

Knock sensor (bank 2)

·

ECM


P0333 Knock sensor voltage is more than 4.838 V for 1 second or more (bank 2).
(1 trip detection logic)

HINT:

When DTC P0327, P0328, P332 or P0333 is stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is delayed to its maximum retardation. Fail-safe mode continues until the ignition switch is turned off.


MONITOR DESCRIPTION

If the output voltage transmitted by the knock sensor remains low or high for more than 1 second, the ECM interprets this as a malfunction in the sensor circuit and the ECM illuminates the MIL and sets a DTC.

CONFIRMATION DRIVING PATTERN

1.
A283032E17
0.188,0.458 1.146,0.76 0.958,0.302 10 false Engine Speed 0.167,2.521 1.125,2.74 0.958,0.219 10 false Vehicle Speed 0.896,1.75 1.271,2 0.375,0.25 10 false Idling 0.156,1 1.281,1.208 1.125,0.208 10 false 2500 to 3000 rpm 3.198,0.896 3.615,1.25 0.417,0.354 10 false [A] 5.396,2.677 5.771,2.896 0.375,0.219 10 false [B] 0.052,2.885 1.313,3.073 1.26,0.188 10 false 10 km/h (6.25 mph) 0.323,3.469 1.313,3.635 0.99,0.167 10 false 0 km/h (0 mph) 2.656,4.188 4.042,4.365 1.385,0.177 10 false 40 seconds or more 4.969,4.177 6.021,4.385 1.052,0.208 10 false 1 minute or more 6.552,3.99 7.021,4.417 0.469,0.427 10 false Time

2.

Connect the GTS to the DLC3.

3.

Turn the ignition switch to ON and turn the GTS on.

4.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON and turn the GTS on.

7.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

8.

With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of between 2500 and 3000 rpm for 40 seconds or more [A].

9.

Drive the vehicle at 10 km/h (6.25 mph) or more for 1 minute or more [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


10.

Enter the following menus: Powertrain / Engine / Trouble Codes.

11.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

13.

Input the DTC: P0327, P0328, P0332 or P0333.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.



15.

If the test result is INCOMPLETE or N/A and no DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

A280067E03
5.594,5.917 6.021,6.135 0.427,0.219 10 false ECM 1.167,3.125 2.646,3.469 1.479,0.344 10 false Knock Sensor (Bank 1) 1.156,2.979 1.615,3.25 0.458,0.271 10 false C36 4.854,2.563 5.25,2.885 0.396,0.323 10 false A34 4.885,2.365 5.135,2.677 0.25,0.313 10 false 28 5.219,2.458 5.719,2.76 0.5,0.302 10 false KNK1 4.844,4.125 5.26,4.438 0.417,0.313 10 false A34 4.885,3.927 5.135,4.24 0.25,0.313 10 false 17 5.219,4.021 5.719,4.323 0.5,0.302 10 false KNK2 4.844,1.406 5.281,1.656 0.438,0.25 10 false A34 4.885,1.198 5.135,1.51 0.25,0.313 10 false 29 5.219,1.302 5.771,1.719 0.552,0.417 10 false EKNK 4.844,0.667 5.229,0.917 0.385,0.25 10 false A36 4.885,0.458 5.135,0.771 0.25,0.313 10 false 29 5.219,0.552 5.5,0.865 0.281,0.313 10 false E1 1.167,4.688 2.729,4.927 1.563,0.24 10 false Knock Sensor (Bank 2) 1.167,4.521 1.604,4.792 0.438,0.271 10 false C34 3.833,2.969 4.073,3.177 0.24,0.208 10 false * 3.833,4.479 4.156,4.771 0.323,0.292 10 false * 4.448,4.531 4.688,4.74 0.24,0.208 10 false * 0.427,5.604 1.75,6 1.323,0.396 10 false *: Shielded 2.563,2.448 2.781,2.74 0.219,0.292 10 false 2 2.552,4.01 2.813,4.271 0.26,0.26 10 false 2 1.104,2.458 1.333,2.688 0.229,0.229 10 false 1 1.104,4.021 1.49,4.354 0.385,0.333 10 false 1

CAUTION / NOTICE / HINT

HINT:
·

If DTC P0327 or P0332 is displayed, check the knock sensor circuit for the right bank (bank 1).

·

If DTC P0328 or P0333 is displayed, check the knock sensor circuit for the left bank (bank 2).

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (+B OF KNOCK SENSOR)
a.
U146754E03
0.438,0.729 0.729,0.917 0.292,0.188 10 false C36 0.115,0.094 0.479,0.292 0.365,0.198 10 false *a 0.844,0.604 1.125,0.802 0.281,0.198 10 false *b 0.448,1.25 0.74,1.438 0.292,0.188 10 false C34 0.844,1.073 1.135,1.271 0.292,0.198 10 false *c

Disconnect the knock sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C36-1 - C36-2 Ignition switch ON 2.4 to 2.6 V
C34-1 - C34-2 Ignition switch ON 2.4 to 2.6 V


Text in Illustration
*a Front view of wire harness connector
(to Knock Sensor)
*b Bank 1
*c Bank 2



OK

2.INSPECT KNOCK SENSOR

NG

4.CHECK HARNESS AND CONNECTOR (ECM - KNOCK SENSOR)
2.INSPECT KNOCK SENSOR

OK

3.CHECK WHETHER DTC OUTPUT RECURS

NG

3.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Start the engine.


i.

Warm up the engine.


j.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


k.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.


l.

Input the DTC: P0327, P0328, P0332, or P0333.


m.

Check the DTC judgment result.

Result
Result Proceed to
NORMAL
(No DTC output)
A
ABNORMAL
(P0327, P0328, P0332, or P0333 output)
B



A

B

4.CHECK HARNESS AND CONNECTOR (ECM - KNOCK SENSOR)
a.

Disconnect the knock sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
A34-28 (KNK1) - C36-2 Always Below 1 Ω
A34-17 (KNK2) - C34-2 Always Below 1 Ω
A36-29 (E1) - C36-1 Always Below 1 Ω
A36-29 (E1) - C34-1 Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
A34-28 (KNK1) or C36-2 - Body ground Always 10 kΩ or higher
A34-17 (KNK2) or C34-2 - Body ground Always 10 kΩ or higher
A36-29 (E1) or C36-1 - Body ground Always 10 kΩ or higher
A36-29 (E1) or C34-1 - Body ground Always 10 kΩ or higher




OK

5.CHECK WHETHER DTC OUTPUT RECURS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Start the engine.


i.

Warm up the engine.


j.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


k.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.


l.

Input the DTC: P0327, P0328, P0332 or P0333.


m.

Check the DTC judgment result.

Result
Result Proceed to
NORMAL
(No DTC output)
A
ABNORMAL
(P0327, P0328, P0332, or P0333 output)
B



A

B