Home › Engine / Hybrid System › FA20 (ENGINE CONTROL) › SFI SYSTEM
RM2090E _51 Engine / Hybrid System _060665 FA20 ENGINE CONTROL _0297470 SFI SYSTEM C

FA20 ENGINE CONTROL  SFI SYSTEM  P0107  Manifold Absolute Pressure / Barometric Pressure Circuit Low Input  P0108  Manifold Absolute Pressure / Barometric Pressure Circuit High Input  


DESCRIPTION

Manifold absolute pressure sensor uses a built-in sensor to detect the intake manifold pressure as a voltage. Additionally, because this measures the absolute pressure as the pressure within the intake manifold without detecting the atmospheric pressure as a standard value, this enables measurements without being influenced by changes in atmospheric pressure from altitude or other causes.

DTC No. DTC Detection Condition Trouble Area
P0107 Manifold absolute pressure sensor voltage is 0.61 V or less for 0.5 seconds or more.
(1 trip detection logic)
·

Open or short in manifold absolute pressure sensor circuit

·

Manifold absolute pressure sensor

·

ECM


P0108 Manifold absolute pressure sensor voltage is 3.906 V or more for 0.5 seconds or more.
(1 trip detection logic)

HINT:

When any of these DTCs are output, check the manifold absolute pressure using the GTS. Enter the following menus: Powertrain / Engine / Data List / MAP.

Manifold Absolute Pressure (kPa [mmHg]) Malfunction
Approximately 0 [0] Short in MAP circuit
141 [1058] or more
·

Short in VC circuit

·

Open in PIM circuit

·

Open in E1 circuit




MONITOR DESCRIPTION

The ECM calculates the manifold absolute pressure based upon the manifold absolute pressure sensor output voltage. If the manifold absolute pressure output voltage is outside the normal range, there may be an abnormality with the manifold absolute pressure, or an open or short in the circuit. In these cases, the ECM will light the check engine warning light, and store the DTC.

CONFIRMATION DRIVING PATTERN

1.
A283032E17
0.188,0.458 1.146,0.76 0.958,0.302 10 false Engine Speed 0.167,2.521 1.125,2.74 0.958,0.219 10 false Vehicle Speed 0.896,1.75 1.271,2 0.375,0.25 10 false Idling 0.156,1 1.281,1.208 1.125,0.208 10 false 2500 to 3000 rpm 3.198,0.896 3.615,1.25 0.417,0.354 10 false [A] 5.396,2.677 5.771,2.896 0.375,0.219 10 false [B] 0.052,2.885 1.313,3.073 1.26,0.188 10 false 10 km/h (6.25 mph) 0.323,3.469 1.313,3.635 0.99,0.167 10 false 0 km/h (0 mph) 2.656,4.188 4.042,4.365 1.385,0.177 10 false 40 seconds or more 4.969,4.177 6.021,4.385 1.052,0.208 10 false 1 minute or more 6.552,3.99 7.021,4.417 0.469,0.427 10 false Time

2.

Connect the GTS to the DLC3.

3.

Turn the ignition switch to ON and turn the GTS on.

4.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON and turn the GTS on.

7.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

8.

With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of between 2500 and 3000 rpm for 40 seconds or more [A].

9.

Drive the vehicle at 10 km/h (6.25 mph) or more for 1 minute or more [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


10.

Enter the following menus: Powertrain / Engine / Trouble Codes.

11.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

13.

Input the DTC: P0107 or P0108.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.



15.

If the test result is INCOMPLETE or N/A and no DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

A280060E03
2.469,0.625 2.719,0.938 0.25,0.313 10 false 3 1.344,2.656 3.146,3.01 1.802,0.354 10 false Manifold Absolute Pressure Sensor 4.865,0.625 5.24,0.969 0.375,0.344 10 false VC 5.292,2.792 5.698,3.063 0.406,0.271 10 false ECM 1.333,2.49 1.927,2.865 0.594,0.375 10 false C18 4.5,0.729 4.958,1.042 0.458,0.313 10 false A36 4.531,0.531 4.781,0.844 0.25,0.313 10 false 19 4.865,1.281 5.302,1.646 0.438,0.365 10 false PIM 4.49,1.396 4.906,1.74 0.417,0.344 10 false A34 4.542,1.208 4.792,1.521 0.25,0.313 10 false 20 4.5,2.115 4.875,2.448 0.375,0.333 10 false A36 4.542,1.917 4.865,2.24 0.323,0.323 10 false 29 2.458,2.01 2.708,2.323 0.25,0.313 10 false 1 2.49,1.281 2.74,1.594 0.25,0.313 10 false 2 4.865,2 5.208,2.375 0.344,0.375 10 false E1 2.167,0.625 2.469,0.938 0.302,0.313 10 false VC 2.125,1.281 2.573,1.646 0.448,0.365 10 false PIM 2.188,2.01 2.49,2.302 0.302,0.292 10 false E2

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (MAP)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / MAP.


e.

Read the value displayed on the GTS.

Standard:

Nearly equal to atmosphere pressure


Reference Value
Condition MAP
Ignition switch ON 80 to 110 kPa

HINT:

Standard atmospheric pressure is 101 kPa (758 mmHg). For every 100 m (328 ft) increase in altitude, pressure drops by 1 kPa. This varies by weather.




OK

NG

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF MANIFOLD ABSOLUTE PRESSURE SENSOR)
2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF MANIFOLD ABSOLUTE PRESSURE SENSOR)
U146748E03
1.333,1.24 0.854,1.646 true 1.667,1.25 1.604,1.625 true 2,1.26 2.417,1.729 true 0.521,1.063 0.813,1.25 0.292,0.188 10 false C18 0.146,0.104 0.51,0.302 0.365,0.198 10 false *a 0.635,1.677 0.844,1.99 0.208,0.313 10 false E2 1.479,1.656 1.76,1.958 0.281,0.302 10 false PIM 2.469,1.708 2.698,2.031 0.229,0.323 10 false VC

a.

Disconnect the manifold absolute pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C18-3 (VC) - C18-1 (E2) Ignition switch ON 4.5 to 5.5 V
C18-2 (PIM) - C18-1 (E2) Ignition switch ON 4.0 to 5.0 V


Text in Illustration
*a Front view of wire harness connector
(to Manifold Absolute Pressure Sensor)



OK

3.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

NG

5.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
3.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
a.

Replace the manifold absolute pressure sensor (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>VACUUM SENSOR>REMOVAL).



NEXT

4.PERFORM CONFIRMATION DRIVING PATTERN
4.PERFORM CONFIRMATION DRIVING PATTERN
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and turn the GTS on.


g.

Start the engine and warm it up.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine / Trouble Codes.


j.

Read the DTC.

Result:
Result Proceed to
DTC P0107 or P0108 is output A
DTC is not output B




A

B

END

5.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
a.

Disconnect the manifold absolute pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
A36-19 (VC) - C18-3 (VC) Always Below 1 Ω
A34-20 (PIM) - C18-2 (PIM) Always Below 1 Ω
A36-29 (E1) - C18-1(E2) Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
A36-19 (VC) or C18-3 (VC) - Body ground Always 10 kΩ or higher
A34-20 (PIM) or C18-2 (PIM) - Body ground Always 10 kΩ or higher
A36-29 (E1) or C18-1 (E2) or Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR