Home › Engine / Hybrid System › FA20 (ENGINE CONTROL) › SFI SYSTEM
RM2090E _51 Engine / Hybrid System _060665 FA20 ENGINE CONTROL _0297470 SFI SYSTEM C

FA20 ENGINE CONTROL  SFI SYSTEM  P000A  Camshaft Position "A" - Timing Slow Response Bank 1  P000C  Camshaft Position "A" - Timing Slow Response Bank 2  P0011  Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1)  P0021  Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 2)  


DESCRIPTION

The Variable Valve Timing (VVT) system adjusts the intake valve timing to improve driveability. The engine oil pressure turns the VVT controller to adjust the valve timing.

The camshaft timing oil control valve assembly is a solenoid valve and switches the engine oil line. The valve moves when the ECM applies 12 V to the solenoid. The ECM changes the energizing time to the solenoid (duty-cycle) in accordance with the camshaft position, crankshaft position, throttle position, etc.

A280185E05
2.344,4.99 2.563,5.208 2.563,5.208 2.969,5.208 true 3.156,4.656 3.406,4.354 3.406,4.354 3.948,4.354 true 0.406,4.427 0.594,3.896 0.594,3.896 0.844,3.896 false 0.635,4.438 1.906,4.677 1.271,0.24 10 false Engine Oil Pressure 0.906,3.813 3.427,4.021 2.521,0.208 10 false Camshaft Timing Oil Control Valve (OCV) 4.042,4.271 5.188,4.458 1.146,0.188 10 false Intake Camshaft 3.042,5.115 6.104,5.292 3.063,0.177 10 false VVT Controller (Camshaft Timing Gear Assembly) 2.115,2.063 3.688,2.375 1.573,0.313 10 false Target Valve Timing 2.063,1.354 3.635,1.667 1.573,0.313 10 false Actual Valve Timing 2.396,2.792 3.125,3.156 0.729,0.365 10 false Correction 5.156,0.906 6.25,1.156 1.094,0.25 10 false VVT Sensor 4.802,1.417 6.49,1.729 1.688,0.313 10 false Crankshaft Position Sensor 4.906,2.438 6.76,2.75 1.854,0.313 10 false Throttle Position Sensor 4.5,2.938 6.719,3.115 2.219,0.177 10 false Engine Coolant Temperature Sensor 4.969,1.927 6.573,2.115 1.604,0.188 10 false Mass Air Flow Meter 4.927,3.458 6.427,3.667 1.5,0.208 10 false Vehicle Speed Sensor 0.396,2.885 1.094,3.135 0.698,0.25 10 false Duty-cycle 2.531,3.219 2.917,3.469 0.385,0.25 10 false ECM 0.177,0.208 1.198,0.781 1.021,0.573 10 false VVT System:

DTC No. DTC Detection Condition Trouble Area
P000A Integrated deviations in target intake valve timing and actual intake valve timing per specified time exceed thresholds (bank 1).
(2 trip detection logic)
·

Valve timing

·

Camshaft timing oil control valve assembly (for intake side of bank 1)

·

Oil control valve filter

·

Camshaft timing gear assembly (for intake side of bank 1)

·

ECM


P0011 Deviation in target intake valve timing and actual intake valve timing exceeds thresholds (bank 1).
(2 trip detection logic)
P000C Integrated deviations in target intake valve timing and actual intake valve timing per specified time exceed thresholds (bank 2).
(2 trip detection logic)
·

Valve timing

·

Camshaft timing oil control valve assembly (for intake side of bank 2)

·

Oil control valve filter

·

Camshaft timing gear assembly (for intake side of bank 2)

·

ECM


P0021 Deviation in target intake valve timing and actual intake valve timing exceeds thresholds (bank 2).
(2 trip detection logic)

MONITOR DESCRIPTION

The ECM optimizes the intake valve timing using the Variable Valve Timing (VVT) system to control the intake camshaft. The VVT system includes the ECM, the camshaft timing oil control valve assembly and the VVT controller (camshaft timing gear assembly). The ECM sends a target duty-cycle control signal to the camshaft timing oil control valve assembly. This control signal regulates the oil pressure supplied to the VVT controller. The VVT controller can advance or retard the intake camshaft.

If the difference between the target and actual intake valve timings is large, and changes in the actual intake valve timing are small, the ECM interprets this as the VVT controller stuck malfunction and stores a DTC.

These DTCs indicate that the VVT controller cannot operate properly due to camshaft timing oil control valve assembly malfunctions or the presence of foreign objects in the camshaft timing oil control valve assembly.


CONFIRMATION DRIVING PATTERN

A280657E07
1.365,2.406 1.667,2.406 1.667,2.406 1.813,2.271 false 3.396,2.271 3.927,2.448 3.927,2.448 4.417,2.281 false 2.365,2.479 2.51,2.281 false 5.448,2.479 5.313,2.281 false 0.135,0.125 1.083,0.531 0.948,0.406 10 false Vehicle Speed 0.51,0.688 1.052,1.104 0.542,0.417 10 false 97 km/h (60 mph) 0.51,1.229 1.052,1.646 0.542,0.417 10 false 64 km/h (40 mph) 0.573,1.708 1.052,2.125 0.479,0.417 10 false 0 km/h (0 mph) 1.74,1.573 2.198,1.875 0.458,0.302 10 false [A] 2.302,1.021 2.76,1.313 0.458,0.292 10 false [B] 3.177,0.5 3.708,0.813 0.531,0.313 10 false [C] 4,0.906 4.427,1.219 0.427,0.313 10 false [D] 4.563,1.083 5.042,1.385 0.479,0.302 10 false [E] 5.042,0.906 5.594,1.281 0.552,0.375 10 false [F] 6.01,1.052 6.458,1.344 0.448,0.292 10 false [G] 0.104,2.313 1.375,2.49 1.271,0.177 10 false 10 seconds or more 1.854,2.51 3.052,2.677 1.198,0.167 10 false Within 20 seconds 3.406,2.458 4.667,2.625 1.26,0.167 10 false 20 seconds or more 5.427,2.51 6.677,2.708 1.25,0.198 10 false Within 10 seconds 6.375,2.24 6.865,2.469 0.49,0.229 10 false Time

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine and warm it up until the engine oil temperature reaches 75°C (167°F) or higher.

7.

Perform the following the confirmation driving pattern.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


(a)

Idle the engine for 10 seconds or more [A].

(b)

Accelerate the vehicle to 97 km/h (60 mph) or more within 20 seconds [B].

(c)

Drive the vehicle at 97 km/h (60 mph) or more for 20 seconds or more [C].

(d)

Release the accelerator pedal to Decelerate until the vehicle speed decreases to less than 64 km/h (40 mph) [D].

HINT:

Release the accelerator pedal fully to perform the fuel-cut.


(e)

Drive the vehicle at 60 km/h (40 mph) or less for 20 seconds or more [E].

(f)

Accelerate the vehicle to 97 km/h (60 mph) or more within 10 seconds [F].

(g)

Release the accelerator pedal and stop the vehicle [G].


8.

Enter the following menus: Powertrain / Engine / Trouble Codes.

9.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

11.

Input the DTC: P000A, P000C, P0011 or P0021.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.



13.

If the test result is INCOMPLETE or N/A and no DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
·

If DTC P000A or P0011 is displayed, check the intake camshaft circuit for the right bank VVT system (bank 1).

·

If DTC P000C or P0021 is displayed, check the intake camshaft circuit for the left bank VVT system (bank 2).

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P000A, P000C, P0011 OR P0021)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read DTCs.

Result
Result Proceed to
DTC P000A, P000C, P0011 or P0021 is output A
DTC P000A, P000C, P0011 or P0021 and other DTCs are output B

HINT:

If any DTCs other than DTC P000A, P000C, P0011 or P0021 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING GTS (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY)

B

2.PERFORM ACTIVE TEST USING GTS (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Turn the A/C switch on.


e.

Enter the following menus: Powertrain / Engine / Active Test / Control the VVT Linear (Bank 1), Control the VVT Linear (Bank 2).


f.

Check the engine speed while operating the camshaft timing oil control valve assembly (for intake camshaft) using the GTS.

OK:
GTS Operation Specified Condition
0 deg (CA) Normal engine speed
36 deg (CA) Engine idles roughly or stalls


HINT:

Refer to "Data List / Active Test" [VVT OCV Duty #1, VVT OCV Duty #2 and VVT Change Angle #1, VVT Change Angle #2] (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST).




OK

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P000A, P000C, P0011 OR P0021)

NG

4.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)
3.CHECK WHETHER DTC OUTPUT RECURS (DTC P000A, P000C, P0011 OR P0021)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Start the engine and warm it up.


i.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


j.

Enter the following menus: Powertrain / Engine / Trouble Codes / Pending.


k.

Read pending DTCs.

Result
Result Proceed to
DTC is not output A
DTC P000A, P000C, P0011 or P0021 is output B

HINT:

DTC P000A, P000C, P0011 or P0021 may be stored when foreign objects in the engine oil are caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. These foreign objects may then be captured by the oil filter.




A

4.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)

B

4.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)

OK

5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT)

NG

5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT)
a.

Inspect the camshaft timing oil control valve assembly (for intake camshaft) (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>CAMSHAFT OIL CONTROL VALVE>INSPECTION).



OK

6.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT)

6.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY
a.

Inspect the camshaft timing gear assembly (See page Engine / Hybrid System>FA20 (ENGINE MECHANICAL)>ENGINE UNIT>INSPECTION).


HINT:

DTC P000A, P000C, P0011 or P0021 may be stored when foreign objects in the engine oil are caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. These foreign objects may then be captured by the oil filter.




OK

7.CLEAN LUBRICATION SYSTEM

NG

REPLACE CAMSHAFT TIMING GEAR ASSEMBLY (FOR INTAKE CAMSHAFT)

7.CLEAN LUBRICATION SYSTEM

b.

Warm up the engine for 5 minutes, and then stop the engine.


c.

Replace the engine oil and filter (See page Engine / Hybrid System>FA20 (LUBRICATION)>OIL AND OIL FILTER>REPLACEMENT).



NEXT

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P000A, P000C, P0011 OR P0021)
8.CHECK WHETHER DTC OUTPUT RECURS (DTC P000A, P000C, P0011 OR P0021)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Start the engine and warm it up.


i.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


j.

Enter the following menus: Powertrain / Engine / Trouble Codes / Pending.


k.

Read pending DTCs.

Result
Result Proceed to
DTC is not output A
DTC P000A, P000C, P0011 or P0021 is output B

HINT:

DTC P000A, P000C, P0011 or P0021 may be stored when foreign objects in the engine oil are caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. These foreign objects may then be captured by the oil filter.




A

END

B