The D-4S system has two fuel injection methods. One is the in-cylinder direct injection method that directly injects pressurized fuel into the combustion chamber. The other is the intake port injection method. The ECM determines which fuel injection method to use in accordance with the engine conditions. For the in-cylinder direction injection method, the injector driver (EDU) in the engine room operates the fuel injectors (for direction injection) at high speeds. The EDU receives fuel injection request signals from the ECM and converts the signals to high voltage / high current injector operation signals to operate the fuel injectors (for direction injection).
The fuel injection sequence occurs in numerical order from No. 1 to No. 4.
The ECM monitors the EDU at all times. If drivers or fuel injectors are malfunctioning, the EDU sends fuel injector operation condition signals (fail signals IJF1 to IJF2) to the ECM. When the ECM receives the signals, the ECM stops the fuel injection control of the appropriate cylinders, cuts voltage to the appropriate injector relay, and illuminates the MIL.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P062D | When injection is finished in all cylinders, the diagnostic signal from the EDU does not change (open or short in the injector or EDU circuit).
(1 trip detection logic) |
·
Open or short in injector driver (EDU) circuit ·
Injector driver (EDU) ·
ECM |
| P1261 | When the injection of No. 1 cylinder is finished, the diagnostic signal from injector driver (EDU) does not change (open or short in No. 1 cylinder injector circuit ).
(1 trip detection logic) |
·
Open or short in fuel injector (for direct injection) circuit (No. 1 cylinder) ·
Injector driver (EDU) ·
Fuel injector assembly (for direct injection) (No. 1 cylinder) ·
ECM |
| P1262 | When the injection of No. 2 cylinder is finished, the diagnostic signal from injector driver (EDU) does not change (open or short in No. 2 cylinder injector circuit ).
(1 trip detection logic) |
·
Open or short in fuel injector (for direct injection) circuit (No. 2 cylinder) ·
Injector driver (EDU) ·
Fuel injector assembly (for direct injection) (No. 2 cylinder) ·
ECM |
| P1263 | When the injection of No. 3 cylinder is finished, the diagnostic signal from injector driver (EDU) does not change (open or short in No. 3 cylinder injector circuit ).
(1 trip detection logic) |
·
Open or short in fuel injector (for direct injection) circuit (No. 3 cylinder) ·
Injector driver (EDU) ·
Fuel injector assembly (for direct injection) (No. 3 cylinder) ·
ECM |
| P1264 | When the injection of No. 4 cylinder is finished, the diagnostic signal from injector driver (EDU) does not change (open or short in No. 4 cylinder injector circuit ).
(1 trip detection logic) |
·
Open or short in fuel injector (for direct injection) circuit (No. 4 cylinder) ·
Injector driver (EDU) ·
Fuel injector assembly (for direct injection) (No. 4 cylinder) ·
ECM |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Record the Freeze Frame Data.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure) (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the GTS on.
Based on engine speed, engine load and other freeze frame data stored in the ECM, reproduce the conditions present when the DTC was stored.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTC.
If a DTC is output, the system is malfunctioning.
If a DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P062D, P1261, P1262, P1263 or P1264.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit |
If the judgment result shown ABNORMAL, the system has a malfunction.
If the judgment result shows NORMAL, the system is normal.
If the test result is INCOMPLETE or N/A and no DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).
If a permanent DTC is output, the system is malfunctioning.
If no permanent DTC is output, the system is normal.
If DTC P1261 is output, check the No. 1 fuel injector (for direct injection) (No. 1 cylinder) circuit.
If DTC P1262 is output, check the No. 2 fuel injector (for direct injection) (No. 2 cylinder) circuit.
If DTC P1263 is output, check the No. 3 fuel injector (for direct injection) (No. 3 cylinder) circuit.
If DTC P1264 is output, check the No. 4 fuel injector (for direct injection) (No. 4 cylinder) circuit.
If the current from the INJ relay is cut because DTC P062D is stored, DTC P1235 will be stored even if the fuel pump assembly (for high pressure) is normal.
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| P1261, P1262, P1263 and/or P1264 are output | A |
| DTC P062D is output | B |
A
B
Disconnect the injector driver (EDU) connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C3-2 (IJ1-) - C3-5 (IJ1+) | 20°C (68°F) | 1.74 to 2.04 Ω |
| C4-1 (IJ2-) - C4-4 (IJ2+) | 20°C (68°F) | 1.74 to 2.04 Ω |
| C3-1 (IJ3-) - C3-4 (IJ3+) | 20°C (68°F) | 1.74 to 2.04 Ω |
| C4-3 (IJ4-) - C4-6 (IJ4+) | 20°C (68°F) | 1.74 to 2.04 Ω |
The standard values shown are fuel injector assembly resistance values.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C3-2 (IJ1-) or C3-5 (IJ1+) - Body ground | 20°C (68°F) | 1 MΩ or higher |
| C4-1 (IJ2-) or C4-4 (IJ2+) - Body ground | 20°C (68°F) | 1 MΩ or higher |
| C3-1 (IJ3-) or C3-4 (IJ3+) - Body ground | 20°C (68°F) | 1 MΩ or higher |
| C4-3 (IJ4-) or C4-6 (IJ4+) - Body ground | 20°C (68°F) | 1 MΩ or higher |
OK
NG
Disconnect the ECM connectors.
Disconnect the injector driver (EDU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A36-14 (#1) - C1-3 (IJT1) | Always | Below 1 Ω |
| A36-25 (#2) - C1-12 (IJT2) | Always | Below 1 Ω |
| A36-24 (#3) - C1-11 (IJT3) | Always | Below 1 Ω |
| A36-23 (#4) - C1-2 (IJT4) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A36-14 (#1) or C1-3 (IJT1) - Body ground | Always | 10 kΩ or higher |
| A36-25 (#2) or C1-12 (IJT2) - Body ground | Always | 10 kΩ or higher |
| A36-24 (#3) or C1-11 (IJT3) - Body ground | Always | 10 kΩ or higher |
| A36-23 (#4) or C1-2 (IJT4) - Body ground | Always | 10 kΩ or higher |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off and wait for at least 30 seconds.
NEXT
Disconnect the injector driver (EDU) connector.
Inspect the ECM using an oscilloscope.
While cranking the engine, check waveform the terminals of the ECM connector.
Signal waveform appears as shown in the illustration.
| ECM Terminal Name | A36-14 (#1) or A36-23 (#4) - Body ground
A36-25 (#2) or A36-24 (#3) - Body ground |
| Tester Range | 2 V/DIV., 4 ms./DIV. |
| Condition | Cranking |
| *a | Component with harness connected
(ECM) |
OK
NG
Disconnect the ECM connector.
Disconnect the injector driver (EDU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A34-11 (IJF1) - C1-6 (IJF1) | Always | Below 1 Ω |
| A34-31 (IJF2) - C1-5 (IJF2) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A34-11 (IJF1) or C1-6 (IJF1) - Body ground | Always | 10 kΩ or higher |
| A34-31 (IJF2) or C1-5 (IJF2) - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the injector driver (EDU) connector.
Inspect the ECM using an oscilloscope.
While start the engine, check waveform the terminals of the ECM connector.
Signal waveform appears as shown in the illustration.
| ECM Terminal Name | A34-11 (IJF1) - Body ground
A34-31 (IJF2) - Body ground |
| Tester Range | 2 V/DIV., 4 ms./DIV. |
| Condition | Idling |
| *a | Component with harness connected
(ECM) |
OK
NG
Inspect the resistance of the fuel injector (for direct injection) (See page Engine / Hybrid System>FA20 FUEL>FUEL INJECTOR(for Direct Injection)>INSPECTION).
OK
NG