Home › Engine / Hybrid System › FA20 (ENGINE CONTROL) › SFI SYSTEM › from 2016.06
RM2090E _51 Engine / Hybrid System _060665 FA20 ENGINE CONTROL _0297470 SFI SYSTEM C

FA20 ENGINE CONTROL  SFI SYSTEM  P062D  No. 1 Fuel Injector Driver Circuit Performance  P1261  DI Injector Circuit / Open - (Cylinder 1)  P1262  DI Injector Circuit / Open - (Cylinder 2)  P1263  DI Injector Circuit / Open - (Cylinder 3)  P1264  DI Injector Circuit / Open - (Cylinder 4)  


DESCRIPTION

The D-4S system has two fuel injection methods. One is the in-cylinder direct injection method that directly injects pressurized fuel into the combustion chamber. The other is the intake port injection method. The ECM determines which fuel injection method to use in accordance with the engine conditions. For the in-cylinder direction injection method, the injector driver (EDU) in the engine room operates the fuel injectors (for direction injection) at high speeds. The EDU receives fuel injection request signals from the ECM and converts the signals to high voltage / high current injector operation signals to operate the fuel injectors (for direction injection).

The fuel injection sequence occurs in numerical order from No. 1 to No. 4.

The ECM monitors the EDU at all times. If drivers or fuel injectors are malfunctioning, the EDU sends fuel injector operation condition signals (fail signals IJF1 to IJF2) to the ECM. When the ECM receives the signals, the ECM stops the fuel injection control of the appropriate cylinders, cuts voltage to the appropriate injector relay, and illuminates the MIL.

DTC No. DTC Detection Condition Trouble Area
P062D When injection is finished in all cylinders, the diagnostic signal from the EDU does not change (open or short in the injector or EDU circuit).
(1 trip detection logic)
·

Open or short in injector driver (EDU) circuit

·

Injector driver (EDU)

·

ECM


P1261 When the injection of No. 1 cylinder is finished, the diagnostic signal from injector driver (EDU) does not change (open or short in No. 1 cylinder injector circuit ).
(1 trip detection logic)
·

Open or short in fuel injector (for direct injection) circuit (No. 1 cylinder)

·

Injector driver (EDU)

·

Fuel injector assembly (for direct injection) (No. 1 cylinder)

·

ECM


P1262 When the injection of No. 2 cylinder is finished, the diagnostic signal from injector driver (EDU) does not change (open or short in No. 2 cylinder injector circuit ).
(1 trip detection logic)
·

Open or short in fuel injector (for direct injection) circuit (No. 2 cylinder)

·

Injector driver (EDU)

·

Fuel injector assembly (for direct injection) (No. 2 cylinder)

·

ECM


P1263 When the injection of No. 3 cylinder is finished, the diagnostic signal from injector driver (EDU) does not change (open or short in No. 3 cylinder injector circuit ).
(1 trip detection logic)
·

Open or short in fuel injector (for direct injection) circuit (No. 3 cylinder)

·

Injector driver (EDU)

·

Fuel injector assembly (for direct injection) (No. 3 cylinder)

·

ECM


P1264 When the injection of No. 4 cylinder is finished, the diagnostic signal from injector driver (EDU) does not change (open or short in No. 4 cylinder injector circuit ).
(1 trip detection logic)
·

Open or short in fuel injector (for direct injection) circuit (No. 4 cylinder)

·

Injector driver (EDU)

·

Fuel injector assembly (for direct injection) (No. 4 cylinder)

·

ECM



CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Record the Freeze Frame Data.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure) (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON and turn the GTS on.

7.

Based on engine speed, engine load and other freeze frame data stored in the ECM, reproduce the conditions present when the DTC was stored.

8.

Enter the following menus: Powertrain / Engine / Trouble Codes.

9.

Read the DTC.

HINT:
·

If a DTC is output, the system is malfunctioning.

·

If a DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

11.

Input the DTC: P062D, P1261, P1262, P1263 or P1264.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit



HINT:
·

If the judgment result shown ABNORMAL, the system has a malfunction.

·

If the judgment result shows NORMAL, the system is normal.



13.

If the test result is INCOMPLETE or N/A and no DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

A384645E01
1.771,1.115 2.573,1.427 0.802,0.313 10 false EFI MAIN1 3.833,1.49 4.25,1.771 0.417,0.281 10 false INJ 2.781,1.74 3.198,2.021 0.417,0.281 10 false INJ 0.792,1.99 1.344,2.271 0.552,0.281 10 false MAIN 0.917,2.573 1.604,2.844 0.688,0.271 10 false Battery 0.75,1.177 1.5,1.448 0.75,0.271 10 false EFI(CTRL) 3.563,0.688 3.854,0.958 0.292,0.271 10 false 1 4.25,0.677 4.542,0.948 0.292,0.271 10 false 2 3.552,1.063 3.844,1.333 0.292,0.271 10 false 3 4.229,1.073 4.521,1.344 0.292,0.271 10 false 5 5.656,0.375 6.073,0.656 0.417,0.281 10 false A35 5.656,0.813 6.073,1.094 0.417,0.281 10 false A35 5.646,1.802 6.063,2.083 0.417,0.281 10 false A33 5.646,4.74 6.063,5.021 0.417,0.281 10 false A34 5.646,5.167 6.063,5.448 0.417,0.281 10 false A34 5.656,5.615 6.073,5.896 0.417,0.281 10 false A36 5.656,6.052 6.073,6.333 0.417,0.281 10 false A36 5.656,6.49 6.073,6.771 0.417,0.281 10 false A36 5.646,6.927 6.063,7.208 0.417,0.281 10 false A36 4.292,6.927 4.708,7.208 0.417,0.281 10 false C1 4.292,6.5 4.708,6.781 0.417,0.281 10 false C1 4.292,6.052 4.708,6.333 0.417,0.281 10 false C1 4.292,5.615 4.708,5.896 0.417,0.281 10 false C1 4.292,5.177 4.708,5.458 0.417,0.281 10 false C1 4.292,4.74 4.708,5.021 0.417,0.281 10 false C1 4.292,4.052 4.708,4.333 0.417,0.281 10 false C2 4.292,3.531 4.708,3.813 0.417,0.281 10 false C2 4.333,3.333 4.677,3.573 0.344,0.24 10 false 1 4.333,3.854 4.677,4.094 0.344,0.24 10 false 2 4.344,4.531 4.688,4.771 0.344,0.24 10 false 6 4.344,4.969 4.688,5.208 0.344,0.24 10 false 5 4.354,5.427 4.698,5.667 0.344,0.24 10 false 3 4.344,6.729 4.688,6.969 0.344,0.24 10 false 2 4.302,5.865 4.646,6.104 0.344,0.24 10 false 12 4.302,6.292 4.646,6.531 0.344,0.24 10 false 11 5.698,6.281 6.042,6.521 0.344,0.24 10 false 24 5.688,5.865 6.031,6.104 0.344,0.24 10 false 25 5.688,6.74 6.031,6.979 0.344,0.24 10 false 23 5.688,5.417 6.031,5.656 0.344,0.24 10 false 14 5.688,4.969 6.031,5.208 0.344,0.24 10 false 31 5.677,4.531 6.021,4.771 0.344,0.24 10 false 11 6,4.75 6.49,4.979 0.49,0.229 10 false IJF1 5.99,5.167 6.479,5.396 0.49,0.229 10 false IJF2 6,5.625 6.375,5.854 0.375,0.229 10 false #1 6,6.042 6.375,6.271 0.375,0.229 10 false #2 6,6.49 6.375,6.719 0.375,0.229 10 false #3 6,6.938 6.375,7.167 0.375,0.229 10 false #4 3.875,4.75 4.365,4.979 0.49,0.229 10 false IJF1 3.875,5.177 4.365,5.406 0.49,0.229 10 false IJF2 3.885,5.604 4.375,5.833 0.49,0.229 10 false IJT1 3.875,6.052 4.365,6.281 0.49,0.229 10 false IJT2 3.885,6.49 4.375,6.719 0.49,0.229 10 false IJT3 3.885,6.917 4.375,7.146 0.49,0.229 10 false IJT4 3.104,3.469 3.594,3.698 0.49,0.229 10 false IJ1+ 3.104,3.833 3.594,4.063 0.49,0.229 10 false IJ1- 3.094,4.76 3.583,4.99 0.49,0.229 10 false IJ2+ 3.094,6.01 3.583,6.24 0.49,0.229 10 false IJ3+ 3.094,7.344 3.583,7.573 0.49,0.229 10 false IJ4+ 3.094,5.146 3.583,5.375 0.49,0.229 10 false IJ2- 3.094,6.427 3.583,6.656 0.49,0.229 10 false IJ3- 3.094,7.74 3.583,7.969 0.49,0.229 10 false IJ4- 3,8.292 4.406,8.688 1.406,0.396 10 false Injector Driver (EDU) 6.167,7.417 6.729,7.698 0.563,0.281 10 false ECM 5.771,8.24 6.698,8.552 0.927,0.313 10 false *: Shielded 0.208,7.865 0.615,8.135 0.406,0.271 10 false C48 0.198,8.042 2.021,8.646 1.823,0.604 10 false No. 4 Fuel Injector Assembly (for Direct Injection) 0.208,6.729 2.031,7.333 1.823,0.604 10 false No. 3 Fuel Injector Assembly (for Direct Injection) 0.219,5.292 0.625,5.563 0.406,0.271 10 false C49 0.229,5.469 2.052,6.073 1.823,0.604 10 false No. 2 Fuel Injector Assembly (for Direct Injection) 0.219,6.563 0.625,6.833 0.406,0.271 10 false C37 0.24,4.135 2.063,4.74 1.823,0.604 10 false No. 1 Fuel Injector Assembly (for Direct Injection) 0.24,3.958 0.646,4.229 0.406,0.271 10 false C11 2.771,3.458 3.188,3.74 0.417,0.281 10 false C3 2.76,3.844 3.177,4.125 0.417,0.281 10 false C3 2.771,6 3.188,6.281 0.417,0.281 10 false C3 2.781,6.427 3.198,6.708 0.417,0.281 10 false C3 2.771,4.76 3.188,5.042 0.417,0.281 10 false C4 2.76,5.167 3.177,5.448 0.417,0.281 10 false C4 2.771,7.354 3.188,7.635 0.417,0.281 10 false C4 2.771,7.75 3.188,8.031 0.417,0.281 10 false C4 2.813,7.146 3.156,7.385 0.344,0.24 10 false 6 2.823,7.552 3.167,7.792 0.344,0.24 10 false 3 2.188,8.01 2.49,8.229 0.302,0.219 10 false * 2.167,6.688 2.469,6.906 0.302,0.219 10 false * 2.198,5.427 2.5,5.646 0.302,0.219 10 false * 2.188,4.104 2.49,4.323 0.302,0.219 10 false * 5.51,2.281 5.813,2.5 0.302,0.219 10 false * 5.521,1.542 5.823,1.76 0.302,0.219 10 false * 0.688,7.604 1.031,7.844 0.344,0.24 10 false 1 0.688,6.292 1.031,6.531 0.344,0.24 10 false 1 0.688,5.021 1.031,5.26 0.344,0.24 10 false 1 0.677,3.708 1.021,3.948 0.344,0.24 10 false 1 1.333,3.698 1.677,3.938 0.344,0.24 10 false 2 1.323,5.01 1.667,5.25 0.344,0.24 10 false 2 1.333,6.281 1.677,6.521 0.344,0.24 10 false 2 1.344,7.594 1.688,7.833 0.344,0.24 10 false 2 5.688,0.167 6.031,0.406 0.344,0.24 10 false 13 5.729,0.604 6.073,0.844 0.344,0.24 10 false 5 5.99,0.385 6.615,0.615 0.625,0.229 10 false SSHUT 5.99,0.802 6.469,1.073 0.479,0.271 10 false IREL 2.813,4.563 3.156,4.802 0.344,0.24 10 false 4 2.802,4.958 3.146,5.198 0.344,0.24 10 false 1 2.813,5.792 3.156,6.031 0.344,0.24 10 false 4 2.802,6.229 3.146,6.469 0.344,0.24 10 false 1 2.823,3.25 3.167,3.49 0.344,0.24 10 false 5 2.813,3.646 3.156,3.885 0.344,0.24 10 false 2 5.99,1.813 6.396,2.052 0.406,0.24 10 false EC 5.719,1.594 6.063,1.833 0.344,0.24 10 false 4 1.698,0.26 1.99,0.531 0.292,0.271 10 false 2 1.688,0.688 1.979,0.958 0.292,0.271 10 false 5 2.365,0.688 2.656,0.958 0.292,0.271 10 false 3 2.365,0.26 2.656,0.531 0.292,0.271 10 false 1 3.958,3.531 4.292,3.792 0.333,0.26 10 false +B 3.875,4.052 4.302,4.323 0.427,0.271 10 false +B2

CAUTION / NOTICE / HINT

HINT:
·

If DTC P1261 is output, check the No. 1 fuel injector (for direct injection) (No. 1 cylinder) circuit.

·

If DTC P1262 is output, check the No. 2 fuel injector (for direct injection) (No. 2 cylinder) circuit.

·

If DTC P1263 is output, check the No. 3 fuel injector (for direct injection) (No. 3 cylinder) circuit.

·

If DTC P1264 is output, check the No. 4 fuel injector (for direct injection) (No. 4 cylinder) circuit.

·

If the current from the INJ relay is cut because DTC P062D is stored, DTC P1235 will be stored even if the fuel pump assembly (for high pressure) is normal.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Result:
Result Proceed to
P1261, P1262, P1263 and/or P1264 are output A
DTC P062D is output B




A

2.CHECK HARNESS AND CONNECTOR

B

6.CHECK HARNESS OR CONNECTOR (ECM - INJECTOR DRIVER (EDU))
2.CHECK HARNESS AND CONNECTOR
a.

Disconnect the injector driver (EDU) connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
C3-2 (IJ1-) - C3-5 (IJ1+) 20°C (68°F) 1.74 to 2.04 Ω
C4-1 (IJ2-) - C4-4 (IJ2+) 20°C (68°F) 1.74 to 2.04 Ω
C3-1 (IJ3-) - C3-4 (IJ3+) 20°C (68°F) 1.74 to 2.04 Ω
C4-3 (IJ4-) - C4-6 (IJ4+) 20°C (68°F) 1.74 to 2.04 Ω


HINT:

The standard values shown are fuel injector assembly resistance values.


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
C3-2 (IJ1-) or C3-5 (IJ1+) - Body ground 20°C (68°F) 1 MΩ or higher
C4-1 (IJ2-) or C4-4 (IJ2+) - Body ground 20°C (68°F) 1 MΩ or higher
C3-1 (IJ3-) or C3-4 (IJ3+) - Body ground 20°C (68°F) 1 MΩ or higher
C4-3 (IJ4-) or C4-6 (IJ4+) - Body ground 20°C (68°F) 1 MΩ or higher




OK

3.CHECK HARNESS AND CONNECTOR (ECM - INJECTOR DRIVER (EDU))

NG

8.INSPECT FUEL INJECTOR ASSEMBLY (FOR DIRECT INJECTION)
3.CHECK HARNESS AND CONNECTOR (ECM - INJECTOR DRIVER (EDU))
a.

Disconnect the ECM connectors.


b.

Disconnect the injector driver (EDU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
A36-14 (#1) - C1-3 (IJT1) Always Below 1 Ω
A36-25 (#2) - C1-12 (IJT2) Always Below 1 Ω
A36-24 (#3) - C1-11 (IJT3) Always Below 1 Ω
A36-23 (#4) - C1-2 (IJT4) Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
A36-14 (#1) or C1-3 (IJT1) - Body ground Always 10 kΩ or higher
A36-25 (#2) or C1-12 (IJT2) - Body ground Always 10 kΩ or higher
A36-24 (#3) or C1-11 (IJT3) - Body ground Always 10 kΩ or higher
A36-23 (#4) or C1-2 (IJT4) - Body ground Always 10 kΩ or higher




OK

4.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

5.CHECK ECM (ECM OUTPUT VOLTAGE)
5.CHECK ECM (ECM OUTPUT VOLTAGE)
a.

Disconnect the injector driver (EDU) connector.


b.
U190111E02
0.646,1.125 1.354,0.583 true 0.594,1.198 0.344,1.844 true 0.635,1.198 1.125,2.052 true 0.688,1.188 1.729,1.885 true 1.406,0.458 1.938,0.646 0.531,0.188 10 false 14 (#1) 0.615,0.385 0.906,0.573 0.292,0.188 10 false A36 0.104,0.104 0.354,0.292 0.25,0.188 10 false *a 0.146,1.875 0.708,2.063 0.563,0.188 10 false 25 (#2) 1.167,2.073 1.656,2.26 0.49,0.188 10 false 24 (#3) 1.76,1.823 2.281,2.01 0.521,0.188 10 false 23 (#4) 0.146,3.135 0.5,3.323 0.354,0.188 10 false CH1 2.99,3.146 3.365,3.333 0.375,0.188 10 false GND

Inspect the ECM using an oscilloscope.

i.

While cranking the engine, check waveform the terminals of the ECM connector.

Standard:

Signal waveform appears as shown in the illustration.


ECM Terminal Name A36-14 (#1) or A36-23 (#4) - Body ground
A36-25 (#2) or A36-24 (#3) - Body ground
Tester Range 2 V/DIV., 4 ms./DIV.
Condition Cranking

Text in Illustration
*a Component with harness connected
(ECM)




OK

REPLACE INJECTOR DRIVER (EDU)

NG

6.CHECK HARNESS OR CONNECTOR (ECM - INJECTOR DRIVER (EDU))
a.

Disconnect the ECM connector.


b.

Disconnect the injector driver (EDU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
A34-11 (IJF1) - C1-6 (IJF1) Always Below 1 Ω
A34-31 (IJF2) - C1-5 (IJF2) Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
A34-11 (IJF1) or C1-6 (IJF1) - Body ground Always 10 kΩ or higher
A34-31 (IJF2) or C1-5 (IJF2) - Body ground Always 10 kΩ or higher




OK

7.CHECK TERMINAL VOLTAGE (ECM OUTPUT VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK TERMINAL VOLTAGE (ECM OUTPUT VOLTAGE)
a.

Disconnect the injector driver (EDU) connector.


b.
U190112E02
2.073,1.125 2.573,0.427 true 2.031,1.25 2.427,1.896 true 2.594,0.292 3.208,0.479 0.615,0.188 10 false 11 (IJF1) 1.948,0.396 2.24,0.583 0.292,0.188 10 false A34 0.146,0.104 0.396,0.292 0.25,0.188 10 false *a 0.115,3.385 0.479,3.573 0.365,0.188 10 false CH1 2.969,3.354 3.344,3.542 0.375,0.188 10 false GND 2.469,1.906 3.094,2.094 0.625,0.188 10 false 31 (IJF2)

Inspect the ECM using an oscilloscope.

i.

While start the engine, check waveform the terminals of the ECM connector.

Standard:

Signal waveform appears as shown in the illustration.


ECM Terminal Name A34-11 (IJF1) - Body ground
A34-31 (IJF2) - Body ground
Tester Range 2 V/DIV., 4 ms./DIV.
Condition Idling

Text in Illustration
*a Component with harness connected
(ECM)




OK

REPLACE INJECTOR DRIVER (EDU)

NG

8.INSPECT FUEL INJECTOR ASSEMBLY (FOR DIRECT INJECTION)
a.

Inspect the resistance of the fuel injector (for direct injection) (See page Engine / Hybrid System>FA20 FUEL>FUEL INJECTOR(for Direct Injection)>INSPECTION).



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

REPLACE FUEL INJECTOR ASSEMBLY (FOR DIRECT INJECTION)