Home › Engine / Hybrid System › FA20 FUEL › FUEL TANK
RM2090E _51 Engine / Hybrid System _060667 FA20 FUEL _0297507 FUEL TANK A

FA20 FUEL  FUEL TANK  INSTALLATION  


PROCEDURE

Hide 77651A 1.INSTALL NO. 1 FUEL TANK CUSHION

a.

Install 10 new No. 1 fuel tank cushions to the fuel tank assembly.


Hide 77204C 2.INSTALL NO. 2 FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.

Install the fuel filter to the No. 2 fuel tank main tube sub-assembly.


b.

Install the No. 2 fuel tank main tube sub-assembly to the fuel tank assembly.


Hide 77213B 3.INSTALL FUEL TANK TO FILLER PIPE HOSE

a.

Install the fuel tank to filler pipe hose to the fuel tank assembly with the clamp.


b.

Tighten the hose clamp bolt.

Torque:
2.0 N*m (20 kgf*cm, 18 in.*lbf)


Hide 77100 4.INSTALL FUEL TANK ASSEMBLY

a.
A282901

Inspect the fuel tank cover.

HINT:

The fuel tank cover is used as a base when attaching the fuel tank assembly, so inspect for any deformation, cracking, or other damage. If any faults are found, replace with a new one.



b.

Hold the fuel tank assembly with an engine lifter.


c.

Temporarily install the fuel tank assembly to the body with the 2 No. 1 fuel tank bands and 4 bolts.


d.
A282902

Adjust the position of the fuel tank assembly to achieve the required separation between the front edge of the fuel tank cover and the holes used for fixing the parking brake cable bracket in place.

Standard:

42 to 44 mm (1.6535 to 1.7323 in.)



e.
A282903

Adjust the position of the fuel tank assembly to achieve the required difference in clearance between the left and right sides of the fuel tank assembly and the body.

Standard:

Below 2 mm (Below 0.0787 in.)



f.
A277995E01
0.757,0 0.928,0.161 0.171,0.161 10 1 2.284,0 2.455,0.161 0.171,0.161 10 2 0.826,1.958 0.997,2.119 0.171,0.161 10 3 2.198,1.958 2.369,2.119 0.171,0.161 10 4

Tighten the 4 bolts in the order shown in the illustration.

Torque:
33 N*m (337 kgf*cm, 24 ft.*lbf)


Hide 77226A 5.CONNECT NO. 6 FUEL TANK BREATHER TUBE (for Clamp Type)

a.

Connect the No. 6 fuel tank breather tube with the clamp.


Hide 77404 6.CONNECT FUEL TANK VENT HOSE SUB-ASSEMBLY (for Metal Type)

a.

Connect the fuel tank vent hose sub-assembly.


Hide 77213B 7.CONNECT FUEL TANK TO FILLER PIPE HOSE (for Clamp Type)

a.

Connect the fuel tank to filler pipe hose to the fuel tank filler pipe sub-assembly with the clamp.


b.

Tighten the hose clamp bolt.

Torque:
2.0 N*m (20 kgf*cm, 18 in.*lbf)


Hide 77740 8.INSTALL CHARCOAL CANISTER ASSEMBLY (for Metal Type)

a.
A282326E03
0.531,0.875 0.729,1.073 0.198,0.198 10 false 1 1.948,1.052 2.146,1.25 0.198,0.198 10 false 2

Connect the quick connector as indicated by the arrows in the order shown in the illustration.


Hide 77404 9.CONNECT FUEL TANK VENT HOSE SUB-ASSEMBLY (for Metal Type)

a.

Engage the clamp to install the tube.


b.

Connect the fuel tank vent hose sub-assembly with the clamp.


Hide 77213B 10.CONNECT FUEL TANK TO FILLER PIPE HOSE (for Metal Type)

a.

Connect the fuel tank to filler pipe hose to the fuel tank filler pipe sub-assembly with the clamp.


b.

Tighten the hose clamp bolt.

Torque:
2.0 N*m (20 kgf*cm, 18 in.*lbf)


Hide 46430 11.INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY

Hide 46420 12.INSTALL NO. 2 PARKING BRAKE CABLE ASSEMBLY

Hide 77642A 13.INSTALL NO. 2 FUEL TANK PROTECTOR (for Clamp Type)

a.

Install the No. 2 fuel tank protector with 2 new nuts and 2 clips.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 77641A 14.INSTALL NO. 1 FUEL TANK PROTECTOR (for Clamp Type)

a.

Install the No. 1 fuel tank protector with 2 new nuts and 2 clips.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 77643A 15.INSTALL NO. 3 FUEL TANK PROTECTOR (for Metal Type)

a.

Install the No. 3 fuel tank protector with a new nut and 2 clips.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 51206A 16.INSTALL REAR SUSPENSION MEMBER SUB-ASSEMBLY

Hide 77020A 18.INSTALL FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE

Hide 19.ADD FUEL

Hide 20.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 58311F 22.INSTALL NO. 2 REAR FLOOR SERVICE HOLE COVER

Hide 58311E 23.INSTALL REAR FLOOR SERVICE HOLE COVER

Hide 71470S 24.INSTALL SEPARATE TYPE REAR SEAT CUSHION ASSEMBLY LH

Hide 71460S 25.INSTALL SEPARATE TYPE REAR SEAT CUSHION ASSEMBLY RH