Home › Engine / Hybrid System › FA20 COOLING › COOLING FAN SYSTEM
RM2090E _51 Engine / Hybrid System _060670 FA20 COOLING _0297520 COOLING FAN SYSTEM J

FA20 COOLING  COOLING FAN SYSTEM  Cooling Fan Circuit  


DESCRIPTION

w/ Air Conditioning System

The ECM turns on or off the fan relays using signals calculated from the engine coolant temperature, air conditioning (ON/OFF), air conditioner refrigerant pressure, engine speed and vehicle speed signals.


The ECM switches the circuit of the cooling fan motors between series and parallel by turning on or off the fan relays in order to control the speed of the cooling fan motors in two steps.

w/o Air Conditioning System

The ECM turns on or off the fan relays using signals calculated from the engine coolant temperature, engine speed and vehicle speed signals.


WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (CONTROL THE ELECTRIC COOLING FAN)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Active Test / Control the Electric Cooling Fan.


e.

Check the operation of the cooling fans while operating them using the GTS.

OK:
Tester Operation Specified Condition
ON Cooling fans operate
OFF Cooling fans stop


Result:
Result Proceed to
OK A
NG (w/o Air Conditioning System) B
NG (w/ Air Conditioning System) C




A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

2.INSPECT ENGINE ROOM RELAY BLOCK (FAN NO. 1 RELAY VOLTAGE)

C

9.INSPECT ENGINE ROOM RELAY BLOCK (FAN NO. 1 RELAY VOLTAGE)
2.INSPECT ENGINE ROOM RELAY BLOCK (FAN NO. 1 RELAY VOLTAGE)
a.
A280291E03
1.146,0.073 1.396,0.292 0.25,0.219 10 false *1 2.563,2.01 2.813,2.229 0.25,0.219 10 false *2

Remove the FAN No. 1 relay from the engine room relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
5 (FAN No. 1 relay terminal) - Body ground Always 11 to 14 V


Text in Illustration
*1 Engine Room Relay Block
*2 FAN No. 1 Relay Terminals


c.

Reinstall the FAN No. 1 relay.



OK

3.CHECK HARNESS AND CONNECTOR (FAN NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - FAN NO. 1 RELAY)

3.CHECK HARNESS AND CONNECTOR (FAN NO. 1 RELAY)
a.
A280291E03
1.146,0.073 1.396,0.292 0.25,0.219 10 false *1 2.563,2.01 2.813,2.229 0.25,0.219 10 false *2

Remove the FAN No. 1 relay from the engine room relay block.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
2 (FAN No. 1 relay terminal) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*1 Engine Room Relay Block
*2 FAN No. 1 Relay Terminals


d.

Reinstall the FAN No. 1 relay.



OK

4.INSPECT FAN NO. 1 RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (FAN NO. 1 RELAY)

4.INSPECT FAN NO. 1 RELAY
a.

Inspect the FAN No. 1 relay (See page Engine / Hybrid System>FA20 COOLING>RELAY>ON-VEHICLE INSPECTION).



OK

5.INSPECT COOLING FAN MOTOR

NG

REPLACE FAN NO. 1 RELAY

5.INSPECT COOLING FAN MOTOR

OK

6.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - BODY GROUND)

NG

6.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - BODY GROUND)
a.

Disconnect the A45 cooling fan motor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A45-1 - Body ground Always Below 1 Ω



c.

Reconnect the A45 cooling fan motor connector.



OK

7.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - ENGINE ROOM RELAY BLOCK)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (COOLING FAN MOTOR - BODY GROUND)

7.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - ENGINE ROOM RELAY BLOCK)
a.

Disconnect the A45 cooling fan motor connector.


b.

Remove the FAN No. 1 relay from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A45-2 - 3 (FAN No. 1 relay terminal) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A45-2 or 3 (FAN No. 1 relay terminal) - Body ground Always 10 kΩ or higher



d.

Reconnect the A45 cooling fan motor connector.


e.

Reinstall the FAN No. 1 relay.



OK

8.CHECK HARNESS AND CONNECTOR (ECM - ENGINE ROOM RELAY BLOCK)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (COOLING FAN MOTOR - ENGINE ROOM RELAY BLOCK)

8.CHECK HARNESS AND CONNECTOR (ECM - ENGINE ROOM RELAY BLOCK)
a.

Disconnect the A35 ECM connector.


b.

Remove the FAN No. 1 relay from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A35-11 (FAN1) - 1 (FAN No. 1 relay terminal) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A35-11 (FAN1) or 1 (FAN No. 1 relay terminal) - Body ground Always 10 kΩ or higher



d.

Reconnect the A35 ECM connector.


e.

Reinstall the FAN No. 1relay.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - ENGINE ROOM RELAY BLOCK)

9.INSPECT ENGINE ROOM RELAY BLOCK (FAN NO. 1 RELAY VOLTAGE)
a.
A280291E03
1.146,0.073 1.396,0.292 0.25,0.219 10 false *1 2.563,2.01 2.813,2.229 0.25,0.219 10 false *2

Remove the FAN No. 1 relay from the engine room relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
5 (FAN No. 1 relay terminal) - Body ground Always 11 to 14 V


Text in Illustration
*1 Engine Room Relay Block
*2 FAN No. 1 Relay Terminals


c.

Reinstall the FAN No. 1 relay.



OK

10.INSPECT ENGINE ROOM RELAY BLOCK (FAN NO. 3 RELAY VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - FAN NO. 1 RELAY)

10.INSPECT ENGINE ROOM RELAY BLOCK (FAN NO. 3 RELAY VOLTAGE)
a.
A280292E03
2.458,0.073 2.708,0.281 0.25,0.208 10 false *1 0.75,1.792 1,2 0.25,0.208 10 false *2

Remove the FAN No. 3 relay from the engine room relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
5 (FAN No. 3 relay terminal) - Body ground Always 11 to 14 V


Text in Illustration
*1 Engine Room Relay Block
*2 FAN No. 3 Relay Terminals


c.

Reinstall the FAN No. 3 relay.



OK

11.CHECK HARNESS AND CONNECTOR (FAN NO. 1, NO. 2 OR NO. 3 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - FAN NO. 3 RELAY)

11.CHECK HARNESS AND CONNECTOR (FAN NO. 1, NO. 2 OR NO. 3 RELAY)
a.
A280293E03
1.656,1.51 1.865,1.74 0.208,0.229 10 false *1 0.563,3.188 0.771,3.417 0.208,0.229 10 false *2 2.135,0.281 2.344,0.51 0.208,0.229 10 false *3 0.24,0.281 0.448,0.51 0.208,0.229 10 false *4

Remove the FAN No. 1, FAN No. 2 and FAN No. 3 relays from the engine room relay block.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
2 (FAN No. 1 relay terminal) - Body ground Ignition switch ON 11 to 14 V
1 (FAN No. 2 relay terminal) - Body ground Ignition switch ON 11 to 14 V
2 (FAN No. 3 relay terminal) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*1 Engine Room Relay Block
*2 FAN No. 1 Relay Terminals
*3 FAN No. 2 Relay Terminals
*4 FAN No. 3 Relay Terminals


d.

Reinstall the FAN No. 1, FAN No. 2 and FAN No. 3 relay.



OK

12.INSPECT FAN NO. 1 RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (FAN NO. 1, NO. 2 OR NO. 3 RELAY)

12.INSPECT FAN NO. 1 RELAY
a.

Inspect the FAN No. 1 relay (See page Engine / Hybrid System>FA20 COOLING>RELAY>ON-VEHICLE INSPECTION).



OK

13.INSPECT FAN NO. 2 RELAY

NG

REPLACE FAN NO. 1 RELAY

13.INSPECT FAN NO. 2 RELAY
a.

Inspect the FAN No. 2 relay (See page Engine / Hybrid System>FA20 COOLING>RELAY>ON-VEHICLE INSPECTION).



OK

14.INSPECT FAN NO. 3 RELAY

NG

REPLACE FAN NO. 2 RELAY

14.INSPECT FAN NO. 3 RELAY
a.

Inspect the FAN No. 3 relay (See page Engine / Hybrid System>FA20 COOLING>RELAY>ON-VEHICLE INSPECTION).



OK

15.CHECK HARNESS AND CONNECTOR (FAN NO. 2 RELAY - BODY GROUND)

NG

REPLACE FAN NO. 3 RELAY

15.CHECK HARNESS AND CONNECTOR (FAN NO. 2 RELAY - BODY GROUND)
a.

Remove the FAN No. 2 relay from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
5 (FAN No. 2 relay terminal) - Body ground Always Below 1 Ω



c.

Reinstall the FAN No. 2 relay.



OK

16.INSPECT COOLING FAN MOTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (FAN NO. 2 RELAY - BODY GROUND)

16.INSPECT COOLING FAN MOTOR

OK

17.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - BODY GROUND)

NG

17.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - BODY GROUND)
a.

Disconnect the A45 cooling fan motor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A45-1 - Body ground Always Below 1 Ω



c.

Reconnect the A45 cooling fan motor connector.



OK

18.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - ENGINE ROOM RELAY BLOCK)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (COOLING FAN MOTOR - BODY GROUND)

18.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - ENGINE ROOM RELAY BLOCK)
a.

Disconnect the A45 cooling fan motor connector.


b.

Remove the FAN No. 1 and FAN No. 2 relays from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A45-2 - 3 (FAN No. 1 relay terminal) Always Below 1 Ω
A45-2 - 4 (FAN No. 2 relay terminal) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A45-2 or 3 (FAN No. 1 relay terminal) or 4 (FAN No. 2 relay terminal) - Body ground Always 10 kΩ or higher



d.

Reconnect the A45 cooling fan motor connector.


e.

Reinstall the FAN No. 1 and FAN No. 2 relays.



OK

19.INSPECT NO. 2 COOLING FAN MOTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (COOLING FAN MOTOR - ENGINE ROOM RELAY BLOCK)

19.INSPECT NO. 2 COOLING FAN MOTOR
a.

Inspect the No. 2 cooling fan motor (See page Engine / Hybrid System>FA20 COOLING>COOLING FAN MOTOR>ON-VEHICLE INSPECTION).



OK

20.CHECK HARNESS AND CONNECTOR (NO. 2 COOLING FAN MOTOR - ENGINE ROOM RELAY BLOCK)

NG

REPLACE NO. 2 COOLING FAN MOTOR

20.CHECK HARNESS AND CONNECTOR (NO. 2 COOLING FAN MOTOR - ENGINE ROOM RELAY BLOCK)
a.

Disconnect the A46 No. 2 cooling fan motor connector.


b.

Remove the FAN No. 2 and FAN No. 3 relays from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A46-1 - 3 (FAN No. 2 relay terminal) Always Below 1 Ω
A46-2 - 3 (FAN No. 3 relay terminal) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A46-1 or 3 (FAN No. 2 relay terminal) - Body ground Always 10 kΩ or higher
A46-2 or 3 (FAN No. 3 relay terminal) - Body ground Always 10 kΩ or higher



d.

Reconnect the A46 No. 2 cooling fan motor connector.


e.

Reinstall the FAN No. 2 and FAN No. 3 relays.



OK

21.INSPECT ENGINE ROOM RELAY BLOCK (FAN NO. 1 RELAY - FAN NO. 2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 2 COOLING FAN MOTOR - ENGINE ROOM RELAY BLOCK)

21.INSPECT ENGINE ROOM RELAY BLOCK (FAN NO. 1 RELAY - FAN NO. 2 RELAY)
a.
A280297E03
1.094,0.385 1.344,0.583 0.25,0.198 10 false *1 2.25,1.906 2.5,2.104 0.25,0.198 10 false *2 2.25,0.469 2.5,0.667 0.25,0.198 10 false *3

Remove the FAN No. 1 and FAN No. 2 relays from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
1 (FAN No. 1 relay terminal) - 2 (FAN No. 2 relay terminal) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
1 (FAN No. 1 relay terminal) or 2 (FAN No. 2 relay terminal) - Body ground Always 10 kΩ or higher


Text in Illustration
*1 Engine Room Relay Block
*2 FAN No. 1 Relay Terminals
*3 FAN No. 2 Relay Terminals


c.

Reinstall the FAN No. 1 and FAN No. 2 relays.



OK

22.CHECK HARNESS AND CONNECTOR (ECM - ENGINE ROOM RELAY BLOCK)

NG

REPLACE ENGINE ROOM RELAY BLOCK

22.CHECK HARNESS AND CONNECTOR (ECM - ENGINE ROOM RELAY BLOCK)
a.

Disconnect the A35 ECM connector.


b.

Remove the FAN No. 2 and FAN No. 3 relays from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A35-11 (FAN1) - 1 (FAN No. 1 relay terminal) Always Below 1 Ω
A35-11 (FAN1) - 2 (FAN No. 2 relay terminal) Always Below 1 Ω
A35-12 (FAN2) - 1 (FAN No. 3 relay terminal) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A35-11 (FAN1) or 1 (FAN No. 1 relay terminal) or 2 (FAN No. 2 relay terminal) - Body ground Always 10 kΩ or higher
A35-12 (FAN2) or 1 (FAN No. 3 relay terminal) - Body ground Always 10 kΩ or higher



d.

Reconnect the A35 ECM connector.


e.

Reinstall the FAN No. 2 and FAN No. 3 relays.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - ENGINE ROOM RELAY BLOCK)