Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › 2012.03–2016.06
RM2090E _51 Engine / Hybrid System _060673 CRUISE CONTROL _0297540 CRUISE CONTROL SYSTEM J

CRUISE CONTROL  CRUISE CONTROL SYSTEM  Cruise Control Switch Circuit  


DESCRIPTION

The cruise control main switch is used to turn the cruise control system on and off, as well as operate 7 functions: SET, - (COAST), TAP-DOWN, RES (RESUME), + (ACCEL), TAP-UP and CANCEL. The SET, TAP-DOWN and - (COAST) functions, and the RES (RESUME), TAP-UP and + (ACCEL) functions are operated with the same switch. The cruise control main switch is an automatic return type switch which turns on only while operating it in the direction of each arrow and turns off after releasing it. The internal contact points of the cruise control main switch turn on with switch operation. Then the ECM reads the voltage value that has been changed by the switch operation to control SET, - (COAST), RES (RESUME), + (ACCEL), and CANCEL.

WIRING DIAGRAM

A280663E04
6.333,0.823 6.823,0.979 0.49,0.156 10 false CCS 6.344,1.51 6.896,1.667 0.552,0.156 10 false EC 5,3.063 5.188,3.219 0.188,0.156 10 false 11 5,3.948 5.219,4.104 0.219,0.156 10 false 10 3.99,3.073 4.094,3.229 0.104,0.156 10 false 4 3.99,3.969 4.104,4.125 0.115,0.156 10 false 3 4.969,3.281 5.24,3.438 0.271,0.156 10 false D51 4.969,4.177 5.24,4.333 0.271,0.156 10 false D51 3.969,3.292 4.146,3.448 0.177,0.156 10 false z5 6.583,5.24 6.958,5.396 0.375,0.156 10 false ECM 3.958,4.188 4.135,4.344 0.177,0.156 10 false z5 0.385,4.708 3.063,5.042 2.677,0.333 10 false Cruise Control Main Switch Assembly 3.177,4.844 4.344,5.167 1.167,0.323 10 false Cruise Control Main Switch Wire 3.521,3.177 3.677,3.333 0.156,0.156 10 false 3 3.521,4.094 3.656,4.25 0.135,0.156 10 false 1 2.875,3.75 3.438,3.906 0.563,0.156 10 false ON-OFF 2.115,3.75 2.583,3.906 0.469,0.156 10 false +/RES 1.344,3.75 1.74,3.906 0.396,0.156 10 false -/SET 0.521,3.75 1.104,3.906 0.583,0.156 10 false CANCEL 4.417,4.698 5.781,5.063 1.365,0.365 10 false Spiral Cable with Sensor Sub-assembly 6.063,0.719 6.25,0.875 0.188,0.156 10 false 30 6.104,1.438 6.25,1.594 0.146,0.156 10 false 4 6.156,5.24 6.469,5.396 0.313,0.156 10 false A33 4.531,3.188 4.896,3.344 0.365,0.156 10 false CCS 4.542,4.094 4.885,4.25 0.344,0.156 10 false ECC 3.281,3.177 3.469,3.333 0.188,0.156 10 false R 3.292,4.094 3.479,4.25 0.188,0.156 10 false B

PROCEDURE

1.READ VALUE ON GTS
E107091E34
2.146,0.083 2.417,0.271 0.271,0.188 10 false *c 2.76,1.177 3,1.375 0.24,0.198 10 false *a 1.979,1.625 2.365,1.823 0.385,0.198 10 false *b 1.031,1.24 1.271,1.438 0.24,0.198 10 false *d

a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Select the following menu items: Powertrain / Cruise Control / Data List.


e.

Check the Data List to confirm proper functioning of the cruise control main switch.

Text in Illustration
*a ON-OFF
*b -/SET
*c +/RES
*d CANCEL

Cruise Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Main SW M-CPU Cruise control main switch signal (Main CPU) / ON or OFF ON: cruise control main switch (ON-OFF button) pushed
OFF: cruise control main switch (ON-OFF button) released
-
Cancel Switch CANCEL switch signal / ON or OFF ON: CANCEL switch on
OFF: CANCEL switch off
-
SET/COAST Switch -/SET switch signal / ON or OFF ON: -/SET switch on
OFF: -/SET switch off
-
RES/ACC Switch +/RES switch signal / ON or OFF ON: +/RES switch on
OFF: +/RES switch off
-

OK:

When the cruise control main switch is operated, the display changes as shown above.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT CRUISE CONTROL MAIN SWITCH ASSEMBLY
2.INSPECT CRUISE CONTROL MAIN SWITCH ASSEMBLY
a.

Inspect the cruise control main switch assembly (See page Engine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL MAIN SWITCH>INSPECTION).



OK

3.CHECK CRUISE CONTROL MAIN SWITCH WIRE

NG

REPLACE CRUISE CONTROL MAIN SWITCH ASSEMBLY

3.CHECK CRUISE CONTROL MAIN SWITCH WIRE
a.

Disconnect the cruise control main switch assembly connector.


b.

Disconnect the spiral cable with sensor sub-assembly connector.


U146781E03
1.313,3.927 0.927,4.198 true 1.771,3.927 2.063,4.125 true 0.573,1.521 0.823,1.688 0.25,0.167 10 false z5 0.323,0.875 0.573,1.042 0.25,0.167 10 false *a 0.813,2.885 1.063,3.052 0.25,0.167 10 false *b 0.802,4.188 0.958,4.354 0.156,0.167 10 false B 2.104,4.115 2.26,4.281 0.156,0.167 10 false R

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Specified Condition
Cruise control main switch side connector terminal 3 (R) - z5-4 Below 1 Ω
Cruise control main switch side connector terminal 1 (B) - z5-3 Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Spiral Cable with Sensor Sub-assembly)
*b Front view of wire harness connector
(to Cruise Control Main Switch Assembly)



OK

4.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

NG

REPAIR OR REPLACE CRUISE CONTROL MAIN SWITCH WIRE

4.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
a.

Inspect the spiral cable with sensor sub-assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION).



OK

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - ECM AND BODY GROUND)

NG

REPLACE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - ECM AND BODY GROUND)
a.

Disconnect the ECM connector.


b.

Disconnect the spiral cable with sensor sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
A33-30 (CCS) - D51-11 (CCS) Always Below 1 Ω
A33-4 (EC) - D51-10 (ECC) Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
A33-30 (CCS) or D51-11 (CCS) - Body ground Always 10 kΩ or higher
A33-4 (EC) or D51-10 (ECC) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - ECM)