Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2012.03–2019.03
RM2090E _54 Brake _060684 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0297617 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  Brake Warning Light Remains ON  


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.

If any of the following is detected, the brake warning light remains on:

·

The skid control ECU (brake actuator assembly) connector is disconnected from the skid control ECU (brake actuator assembly).

·

The brake fluid level is insufficient.

·

The parking brake is applied.

·

EBD operation is not possible.


WIRING DIAGRAM

C264063E03
4.344,2.021 4.865,2.219 0.521,0.198 10 false CANH 4.344,2.438 4.875,2.729 0.531,0.292 10 false CANL 4.344,0.344 4.833,0.563 0.49,0.219 10 false CANL 4.344,0.74 4.844,0.938 0.5,0.198 10 false CANH 5.979,2.438 6.458,2.677 0.479,0.24 10 false CANL 5.979,2.01 6.51,2.25 0.531,0.24 10 false CANH 4.906,2.01 5.292,2.25 0.385,0.24 10 false D5 4.906,2.458 5.24,2.677 0.333,0.219 10 false D5 2.229,0.438 2.49,0.667 0.26,0.229 10 false 17 5.708,1.875 5.99,2.094 0.281,0.219 10 false 26 5.708,2.281 5.979,2.531 0.271,0.25 10 false 14 5.979,4.313 6.354,4.542 0.375,0.229 10 false IG1 5.719,4.219 5.979,4.406 0.26,0.188 10 false 28 5.979,5.135 6.521,5.385 0.542,0.25 10 false GND1 5.542,5.698 5.844,5.948 0.302,0.25 10 false A5 2.469,0.542 2.781,0.729 0.313,0.188 10 false LBL 2.677,1.042 3.031,1.281 0.354,0.24 10 false D7 2.677,1.208 4.625,1.479 1.948,0.271 10 false Combination Meter Assembly 2.104,4.323 3.167,4.646 1.063,0.323 10 false from IG1 Circuit 4.344,4.49 5.25,4.771 0.906,0.281 10 false ECU IG1 5.542,5.865 7.156,6.531 1.615,0.667 10 false Skid Control ECU (Brake Actuator Assembly) 3.135,2.01 3.344,2.229 0.208,0.219 10 false 14 3.51,2.75 5.01,3.49 1.5,0.74 10 false Main Body ECU (Network Gateway ECU) 2.292,2.74 3.396,3.552 1.104,0.813 10 false Instrument Panel Junction Block Assembly 2.125,2.229 2.5,2.479 0.375,0.25 10 false 3B 2.135,2 2.375,2.219 0.24,0.219 10 false 24 1.75,0.438 1.948,0.719 0.198,0.281 10 false 1 1.729,2.125 1.938,2.302 0.208,0.177 10 false 1 0.781,0.438 1.104,0.74 0.323,0.302 10 false 2 0.573,0.813 0.938,1.01 0.365,0.198 10 false A59 0.573,0.979 2.24,2.01 1.667,1.031 10 false Brake Fluid Level Warning Switch (Brake Master Cylinder Sub-assembly) 0.583,2.5 0.896,2.708 0.313,0.208 10 false D31 0.583,2.688 1.99,3.031 1.406,0.344 10 false Parking Brake Switch Assembly 5.719,5.031 5.979,5.229 0.26,0.198 10 false 38 4.833,0.563 5.083,0.802 0.25,0.24 10 false 6 4.813,0.177 5.021,0.406 0.208,0.229 10 false 7 4.906,2.24 5.167,2.5 0.26,0.26 10 false 13 4.896,1.802 5.135,1.979 0.24,0.177 10 false 14 5.969,3.542 6.365,3.76 0.396,0.219 10 false +BS 5.719,3.448 6.021,3.667 0.302,0.219 10 false 25 2.302,3.542 3.135,3.917 0.833,0.375 10 false from Battery 4.271,3.698 5.073,3.979 0.802,0.281 10 false ABS NO. 2 0.823,6.188 2.521,6.542 1.698,0.354 10 false :CAN Communication Line 3.479,2.229 3.792,2.417 0.313,0.188 10 false PKB 3.115,2.219 3.427,2.406 0.313,0.188 10 false MB

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform VSC sensor neutral memorization (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if a CAN communication system DTC is output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result:
Result Proceed to
DTC is not output. A
DTC is output. B




A

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED

B

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake actuator assembly) connector is securely connected.

OK:

The connector is securely connected.




OK

3.CHECK BATTERY

NG

CONNECT CONNECTOR TO ECU CORRECTLY

3.CHECK BATTERY
a.

Check the battery voltage.

Standard Voltage:

11 to 14 V




OK

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

NG

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.
U147145E01
0.073,0.083 0.239,0.233 0.166,0.151 10 *a 0.655,0.47 0.655,0.867 false 1.202,0.478 1.202,0.923 false 2.742,0.487 2.742,0.862 false 0.503,0.289 0.844,0.440 0.341,0.151 10 +BS 1.061,0.301 1.382,0.451 0.321,0.151 10 IG1 2.604,0.314 3.082,0.465 0.479,0.151 10 GND1 1.598,0.198 1.854,0.348 0.256,0.151 10 A5

Disconnect the skid control ECU (brake actuator assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A5-25 (+BS) - Body ground Always 11 to 14 V
A5-25 (+BS) - A5-38 (GND1) Always 11 to 14 V
A5-28 (IG1) - Body ground Ignition switch ON 11 to 14 V
A5-28 (IG1) - A5-38 (GND1) Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))



OK

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.
U147144E01
0.073,0.083 0.239,0.233 0.166,0.151 10 *a 2.742,0.487 2.742,0.862 false 2.518,0.314 2.984,0.465 0.467,0.151 10 GND1 1.598,0.198 1.854,0.348 0.256,0.151 10 A5

Turn the ignition switch off.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A5-38 (GND1) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))



OK

6.READ VALUE USING GTS (PARKING BRAKE SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

6.READ VALUE USING GTS (PARKING BRAKE SWITCH)
a.

Reconnect the skid control ECU (brake actuator assembly) connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Select the Data List using the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Parking Brake SW Parking brake switch / ON or OFF ON: Parking brake applied
OFF: Parking brake released
-


e.

Using the GTS, check the switch operation signal received when the parking brake is operated.

OK:

When the parking brake is operated, the display changes as shown above.




OK

7.INSPECT BRAKE FLUID LEVEL WARNING SWITCH

NG

10.INSPECT PARKING BRAKE SWITCH ASSEMBLY
7.INSPECT BRAKE FLUID LEVEL WARNING SWITCH
a.
C261878E01
0.073,0.065 0.239,0.215 0.166,0.151 10 *a

Turn the ignition switch off.


b.

Remove the reservoir filler cap and the strainer.


c.

Disconnect the brake fluid level warning switch connector.


d.

Measure the resistance according to the value(s) in the table below.

HINT:

A float is located inside the reservoir. Its position changes according to the brake fluid level.


Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Switch OFF (Float up) 1.9 to 2.1 kΩ
1 - 2 Switch ON (Float down) Below 1 Ω


Text in Illustration
*a Component without harness connected
(Brake Fluid Level Warning Switch (Brake Master Cylinder Sub-assembly))

HINT:

If there is no problem after finishing the above check, adjust the brake fluid level to the MAX level.


Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C




A

8.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE FLUID LEVEL WARNING SWITCH)

B

REPLACE BRAKE MASTER CYLINDER SUB-ASSEMBLY

C

REPLACE BRAKE MASTER CYLINDER SUB-ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE FLUID LEVEL WARNING SWITCH)
a.

Disconnect the combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D7-17 (LBL) - A59-1 Always Below 1 Ω
D7-17 (LBL) - Body ground Always 10 kΩ or higher
A59-2 - Body ground Always Below 1 Ω




OK

9.INSPECT COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT COMBINATION METER ASSEMBLY
a.

Reconnect the combination meter assembly connector and the brake fluid level warning switch connector.


b.

Perform an Active Test of the combination meter assembly (meter CPU) using the GTS (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).


c.

Check the combination meter assembly.

OK:

The brake warning light turns on or off in accordance with the Active Test operation.


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE).




OK

NG

REPLACE COMBINATION METER ASSEMBLY

10.INSPECT PARKING BRAKE SWITCH ASSEMBLY
a.
C211519E14
0.198,0.167 0.51,0.365 0.313,0.198 10 false *a

Turn the ignition switch off.


b.

Disconnect the parking brake switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - Body ground Parking brake switch ON
(Switch pin free)
Below 1 Ω
1 - Body ground Parking brake switch OFF
(Switch pin pushed in)
10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Parking Brake Switch Assembly)



OK

11.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - PARKING BRAKE SWITCH ASSEMBLY)

NG

REPLACE PARKING BRAKE SWITCH ASSEMBLY

11.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - PARKING BRAKE SWITCH ASSEMBLY)
a.

Disconnect the instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3B-24 - D31-1 Always Below 1 Ω
3B-24 - Body ground Always 10 kΩ or higher




OK

12.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Remove the main body ECU (network gateway ECU) from the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


c.

Measure the resistance according to the value(s) in the table below.

U147276E01
0.116,0.085 0.302,0.246 0.186,0.161 10 *a 2.061,0.48 2.288,0.636 0.228,0.156 10 MB 5.618,0.276 5.806,0.432 0.189,0.156 10 3B 1.756,1.324 2.078,1.488 0.322,0.164 10 PKB 1.896,1.063 1.896,1.3 false

Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -

Standard Resistance:
Tester Connection Condition Specified Condition
MB-14 (PKB) - 3B-24 Always Below 1 Ω
MB-14 (PKB) - Body ground Always 10 kΩ or higher


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE).




OK

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY