Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2016.06
RM2090E _54 Brake _060684 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0297617 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  Hill Start Assist Indicator Circuit  


DESCRIPTION

The skid control ECU (brake actuator assembly) controls display of the hill start assist indicator in the combination meter assembly via CAN communication.

Turning the hill-start assist control on and off, the hill start assist indicator in the combination meter assembly turns on and off. If the hill-start assist control is not functioning properly when the system is turned on, the hill start assist indicator goes off and the buzzer sounds.

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform VSC sensor neutral memorization (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.PRE-CHECK
a.

Check the status of the hill start assist indicator when the hill-start assist control is not functioning.

OK:

The hill start assist indicator is on.


HINT:

When the hill start assist indicator is off or the buzzer sounds, the ECM enters fail-safe mode, and the hill-start assist control does not function.



b.

Check that the hill-start assist control was not deactivated by operation of the VSC OFF switch.

Result:

The hill-start assist control was deactivated.




A

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED

B

HILL-START ASSIST FUNCTION ON

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED
a.

Move the connector and wire harness of the skid control ECU (brake actuator assembly) lightly up and down and to right and left to check the status of the hill start assist indicator in the combination meter assembly.

OK:

The status of the hill start assist indicator does not change.




OK

3.CHECK CAN COMMUNICATION SYSTEM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CAN COMMUNICATION SYSTEM
a.

Check if a CAN communication system DTC is output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

OK:

No DTC is output.




OK

4.READ VALUE USING GTS (HILL START ASSIST INDICATOR AND HA-CTRL BUZZER)

NG

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

4.READ VALUE USING GTS (HILL START ASSIST INDICATOR AND HA-CTRL BUZZER)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Select the Active Test using the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
Hill Start Assist Indicator Hill Start Assist Indicator Indicator light ON/OFF Observe combination meter assembly
HA-CTRL Buzzer HA-CTRL buzzer Buzzer ON/OFF Buzzer can be heard
HINT:

If the hill-start assist function is set to OFF, the buzzer will not sound even when HA-CTRL buzzer ON/OFF operation is performed.




d.

Perform Active Test for the hill start assist indicator and the HA-CTRL buzzer.

OK:

The hill start assist indicator and the HA-CTRL buzzer are turned on and off when Active Test ON/OFF is performed.




OK

5.INSPECT VSC OFF SWITCH

NG

GO TO METER / GAUGE / DISPLAY (HOW TO PROCEED WITH TROUBLESHOOTING)

5.INSPECT VSC OFF SWITCH

OK

6.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - VSC OFF SWITCH)

NG

6.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - VSC OFF SWITCH)
a.

Turn the ignition switch off.


b.

Disconnect the VSC OFF switch connector.


c.

Disconnect the skid control ECU (brake actuator assembly) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D35-5 - A5-12 (CSW1) Always Below 1 Ω
A5-12 (CSW1) - Body ground Always 10 kΩ or higher
D35-8 - Body ground Always Below 1 Ω




OK

7.CHECK HARNESS AND CONNECTOR (+BS, IG1, GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (+BS, IG1, GND1 TERMINAL)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

No malfunction is detected.



b.

Turn the ignition switch off.


c.

Disconnect the skid control ECU (brake actuator assembly) connector.


d.

Check that there is no deformation or corrosion on the case or the terminals of the connector.

OK:

No deformation or corrosion is present.



e.
U190371E01
0.073,0.083 0.239,0.233 0.166,0.151 10 *a 0.655,0.47 0.655,0.867 false 1.202,0.478 1.202,0.923 false 2.742,0.487 2.742,0.862 false 0.503,0.289 0.844,0.440 0.341,0.151 10 +BS 1.061,0.301 1.382,0.451 0.321,0.151 10 IG1 2.604,0.314 3.082,0.465 0.479,0.151 10 GND1 1.598,0.198 1.854,0.348 0.256,0.151 10 A5

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A5-25 (+BS) - Body ground Always 11 to 14 V
A5-25 (+BS) - A5-38 (GND1) Always 11 to 14 V
A5-28 (IG1) - Body ground Ignition Switch ON 11 to 14 V
A5-28 (IG1) - A5-38 (GND1) Ignition Switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR