Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY › from 2016.06
RM2090E _55 Steering _060690 STEERING COLUMN _0297646 STEERING COLUMN ASSEMBLY A

STEERING COLUMN  STEERING COLUMN ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing the steering column. (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION)


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 2.TURN FRONT WHEELS TO FACE STRAIGHT AHEAD

Hide 5.REMOVE STEERING WHEEL ASSEMBLY

Hide 55318C 6.REMOVE INSTRUMENT SIDE PANEL (w/o Knee Airbag)

a.
B322065E02
1.229,1.813 0.75,1.927 false 0.563,1.865 0.906,2.063 0.344,0.198 10 false *1

Using a moulding remover, disengage the claw and 4 clips and remove the instrument side panel.

Text in Illustration
*1 Moulding Remover


Hide 55606 7.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/o Knee Airbag)

Hide 73900 8.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Knee Airbag)

Hide 55461A 9.REMOVE INSTRUMENT PANEL ORNAMENT (w/ Large Ornament Panel)

Hide 55405B 10.REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/o Large Ornament Panel)

Hide 55422 12.REMOVE UPPER INSTRUMENT PANEL METER ORNAMENT

Hide 45289A 13.REMOVE STEERING COLUMN COVER SUPPORT (w/ Entry and Start System)

a.
C260477

Disengage the 4 claws and remove the steering column cover support.


Hide 14.REMOVE LOWER STEERING COLUMN COVER

a.

w/ Knee Airbag

i.
C260510

Remove the 2 screws.


ii.

Disengage the 4 claws and remove the lower steering column cover.



b.

w/o Knee Airbag

i.
C260467

Remove the 2 screws.


ii.

Disengage the 6 claws and remove the lower steering column cover.



Hide 45286 15.REMOVE UPPER STEERING COLUMN COVER

a.
C260468

Disengage the 2 claws to remove the upper steering column cover.


Hide 16.REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

a.

Disconnect the each connector from the turn signal switch assembly with spiral cable sub-assembly.


b.

Using pliers, loosen the clamp.


c.
C260469E01
2.164,0.995 2.376,1.156 0.213,0.161 10 *1 2.136,0.706 2.349,0.866 0.213,0.161 10 *2 1.85,0.771 2.125,0.789 false 1.835,0.896 2.136,1.067 false

With the clamp loosened, use a screwdriver to disengage the claw, and remove the turn signal switch assembly with spiral cable sub-assembly from the steering column assembly.

Text in Illustration
*1 Clamp
*2 Claw

NOTICE:
·

Do not replace the spiral cable with the battery connected and the ignition switch ON.

·

Do not rotate the spiral cable with the battery connected and the ignition switch ON.

·

Ensure that the steering wheel is installed and aligned straight when inspecting the steering sensor.




Hide 45260 17.REMOVE STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C263656E03
1.563,0.583 2.052,0.813 2.052,0.813 1.563,0.677 true 2.104,0.792 2.292,0.948 0.188,0.156 10 false *1

Put matchmarks on the steering intermediate shaft assembly and the steering column assembly.

Text in Illustration
*1 Matchmark


b.

Remove the bolt and separate the steering intermediate shaft assembly from the steering column assembly.


c.
C260472E01
1.511,0.7 1.964,0.524 1.964,0.524 1.488,0.623 false 1.982,0.428 2.168,0.590 0.186,0.161 10 *1

Put matchmarks on the steering intermediate shaft assembly and the rack and pinion power steering gear assembly.

Text in Illustration
*1 Matchmark


d.

Remove the bolt and separate the steering intermediate shaft assembly from the rack and pinion power steering gear assembly.


e.
C260470

Disengage the 4 claws remove the steering intermediate shaft assembly from the exterior of the vehicle cabin.


Hide 45250 18.REMOVE STEERING COLUMN ASSEMBLY

a.
C260473E02
0.167,0.135 0.375,0.375 0.208,0.24 10 false *a 1.375,0.135 1.583,0.375 0.208,0.24 10 false *b

Disconnect the 2 connectors from the power steering ECU assembly.

i.

As shown illustration, pull out the lock of the lock lever and turn the lock lever to disconnect the connector.

Text in Illustration
*a Pull out the lock
*b Turn the lock lever



b.

Disengage the clamp.


c.

Disconnect the each connector and disengage the wire harness clamps from the steering column assembly.


d.
C260474

Remove the bolt and 2 nuts to remove the steering column assembly.

HINT:

When pulling the bolts out, lifting the motor section of the steering column assembly and tilting the steering column assembly will make it easier to remove the bolts.