Home › Vehicle Interior › DOOR LOCK › KEY REMINDER WARNING SYSTEM(w/o Entry and Start System)
RM2090E _58 Vehicle Interior _060696 DOOR LOCK _0297669 KEY REMINDER WARNING SYSTEM(w/o Entry and Start System) J

DOOR LOCK  KEY REMINDER WARNING SYSTEM(w/o Entry and Start System)  Key Reminder Buzzer does not Sound  


DESCRIPTION

The key reminder warning buzzer sounds when the driver side door is opened while the ignition switch is in the LOCK or ACC positions. The key reminder warning buzzer is activated when the main body ECU (network gateway ECU) sends a buzzer sound request signal to the combination meter assembly.

WIRING DIAGRAM

B312722E03
1.156,3.177 1.625,3.354 0.469,0.177 10 false MB 1.167,2.979 1.823,3.156 0.656,0.177 10 false 16 1.177,1.896 1.729,2.063 0.552,0.167 10 false 22 3.146,2.021 3.25,2.177 0.104,0.156 10 false 2 4.708,3.094 4.813,3.25 0.104,0.156 10 false 1 4.594,2 4.698,2.156 0.104,0.156 10 false 1 4.5,3.656 6.49,4.302 1.99,0.646 10 false Front Door Courtesy Light Switch Assembly LH*1/RH*2 4.5,3.5 5.958,3.667 1.458,0.167 10 false H21*1, G18*2 2.75,2.51 5.24,2.833 2.49,0.323 10 false Un-lock Warning Switch Assembly 2.75,2.333 3.365,2.5 0.615,0.167 10 false D53 0.073,4.677 1.802,5.302 1.729,0.625 10 false Main Body ECU (Network Gateway ECU) 1.177,2.115 1.677,2.302 0.5,0.188 10 false D5 0.729,5.458 2.833,5.75 2.104,0.292 10 false : CAN communication Line 2.063,1.333 4.115,1.813 2.052,0.479 10 false Combination Meter Assembly (Key Reminder Warning Buzzer) 3.344,3.083 3.531,3.229 0.188,0.146 10 false 28 1.125,3.75 2.073,3.938 0.948,0.188 10 false 3A 1.115,3.927 2.906,4.385 1.792,0.458 10 false Instrument Panel Junction Block Assembly 4.875,2.25 5.458,2.458 0.583,0.208 10 false HAZ 5.677,2.135 7.063,2.469 1.385,0.333 10 false from MAIN Fuse 0.646,3.167 1.781,3.375 1.135,0.208 10 false FDCY 0.698,2.104 1.323,2.281 0.625,0.177 10 false KSW 3.333,2.031 3.802,2.208 0.469,0.177 10 false UN- 4.26,2.031 4.854,2.188 0.594,0.156 10 false UN+ 3,5.448 5.104,5.74 2.104,0.292 10 false *1: for LHD 4.323,5.448 6.427,5.74 2.104,0.292 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Since the key reminder warning system has functions that use CAN communication, first confirm that there is no malfunction in the communication system by inspecting the CAN communication functions in accordance with How to Proceed with Troubleshooting. Then conduct the following troubleshooting procedure.


PROCEDURE

1.READ VALUE USING GTS (D DOOR COURTESY SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
D Door Courtesy SW Driver side door courtesy light switch signal / ON or OFF ON: Driver side door opened
OFF: Driver side door closed
-

OK:

ON or OFF appears on the screen according to the driver door condition.




OK

2.READ VALUE USING GTS (KEY UNLOCK WARNING SW)

NG

GO TO LIGHTING SYSTEM (DOOR COURTESY LIGHT SWITCH CIRCUIT)

2.READ VALUE USING GTS (KEY UNLOCK WARNING SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Key Unlock warning SW Unlock warning switch signal / OFF or ON OFF: Ignition key is not inserted
ON: Ignition key is inserted
-

OK:

When the un-lock warning switch assembly is operated, the display changes as shown in the table.




OK

3.CHECK COMBINATION METER ASSEMBLY (BUZZER OPERATION)

NG

4.INSPECT UN-LOCK WARNING SWITCH ASSEMBLY
3.CHECK COMBINATION METER ASSEMBLY (BUZZER OPERATION)
a.

Remove the key from the key cylinder, turn the light control switch on the headlight dimmer switch assembly to the tail position, and open the driver door.

OK:

The light reminder warning buzzer sounds.


HINT:

The key reminder warning system sounds the buzzer built in to the combination meter for key reminder warnings. This buzzer is also used for the light reminder warning system. Therefore, check the operation of the combination meter buzzer by checking if the buzzer sounds to inform that the lights are still on.




OK

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU)

NG

REPLACE COMBINATION METER ASSEMBLY

4.INSPECT UN-LOCK WARNING SWITCH ASSEMBLY
a.

Remove the un-lock warning switch assembly (See page Vehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>REMOVAL).


b.

Inspect the un-lock warning switch assembly (See page Vehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>INSPECTION).



OK

5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - UNLOCK WARNING SWITCH ASSEMBLY)

NG

REPLACE UN-LOCK WARNING SWITCH ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - UNLOCK WARNING SWITCH ASSEMBLY)
a.

Disconnect the D53 un-lock warning switch assembly connector.


b.

Disconnect the D5 main body ECU (network gateway ECU) connector.


c.
U146904E01
0.191,0.118 0.377,0.279 0.186,0.161 10 *a 1.574,0.28 1.870,0.436 0.295,0.156 10 D53 1.072,1.425 1.51,1.425 false 1.949,1.425 2.386,1.425 false 2.438,1.337 2.785,1.493 0.347,0.156 10 UN- 0.686,1.337 1.033,1.493 0.347,0.156 10 UN+

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D53-1 (UN+) - Body ground Always 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
D53-2 (UN-) - D5-22 (KSW) Always Below 1 Ω
D53-2 (UN-) - Body ground Always 10 kΩ or higher



Text in Illustration
*a Front view of wire harness connector
(to Un-lock Warning Switch Assembly)


OK

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR