Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT
RM2090E _58 Vehicle Interior _060704 HEATING / AIR CONDITIONING _0297739 AIR CONDITIONING UNIT A

HEATING / AIR CONDITIONING  AIR CONDITIONING UNIT  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

CAUTION:

Be sure to read Precaution thoroughly before servicing (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 2. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 4.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:
·

The power window system utilizes a mechanism that the door glass moves down slightly when the door is opened, and that the glass moves up when closing the door in order to prevent the door molding from being damaged. When the battery negative (-) terminal needs to be disconnected for servicing, fully open the driver and passenger door glasses in advance.



Hide 87245A 5.DISCONNECT INLET HEATER WATER HOSE A

a.
E250341

Using pliers, grip the claws of the clip and slide the clip to disconnect the inlet heater water hose A.

NOTICE:
·

Do not apply excessive force to the inlet heater water hose A.

·

Prepare a drain pan or cloth in case the coolant leaks.

·

Since the inlet heater water hose A must be installed in a predefined position, apply matching marks before removing it.




Hide 87246A 6.DISCONNECT OUTLET HEATER WATER HOSE A

a.
E250342

Using pliers, grip the claws of the clip and slide the clip to disconnect the outlet heater water hose A.

NOTICE:
·

Do not apply excessive force to the outlet heater water hose A.

·

Prepare a drain pan or cloth in case the coolant leaks.

·

Since the outlet heater water hose A must be installed in a predefined position, apply matching marks before removing it.




Hide 88704 7.DISCONNECT SUCTION HOSE SUB-ASSEMBLY

a.
E246449

Remove the bolt and slide the hook connector.


b.

Disconnect the suction hose sub-assembly.


c.

Remove the O-ring from the suction hose sub-assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



Hide 88790E 8.DISCONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY

a.

Disconnect the air conditioner tube and accessory assembly.


b.

Remove the O-ring from the air conditioner tube and accessory assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



Hide 55302C 9.REMOVE INSTRUMENT PANEL SUB-ASSEMBLY

Hide 73900 10.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIR BAG ASSEMBLY (w/ Knee Airbag)

Hide 45250 11.REMOVE STEERING COLUMN ASSEMBLY

Hide 67914 12.REMOVE FRONT DOOR SCUFF PLATE LH

Hide 67913 13.REMOVE FRONT DOOR SCUFF PLATE RH

Hide 62112 14.REMOVE COWL SIDE TRIM BOARD LH

Hide 62111C 15.REMOVE COWL SIDE TRIM BOARD RH

Hide 55330B 16.REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY

a.

for Driver Side

i.

Using a T20 "TORX" socket wrench, remove the 2 bolts.

E255871E01
0.817,2.129 1.007,2.291 0.190,0.162 10 *1 1.512,2.014 0.976,2.201 0.976,2.201 1.516,2.335 false

Text in Illustration
*1 "TORX" Bolt - -


ii.

Remove the bolt.


iii.

Disconnect each connector and disengage the clamp and 2 claws.



b.

for Center Side

i.

Remove the each bolts and disengage the clip.

E255872E01
4.588,1.224 4.774,1.397 0.186,0.173 10 *a 4.944,1.08 4.751,1.279 false 1.853,4.297 2.052,4.460 0.199,0.164 10 *A

Text in Illustration
*A for Automatic Air Conditioning System - -
*a Disengage the lock plate and disconnect connector. - -


ii.

Disconnect each connector and disengage the each clamp.



c.

for Front Passenger Side

i.

Using a T20 "TORX" socket wrench, remove the 2 bolts.

E256300E01
0.991,0.23 1.209,0.394 0.218,0.164 10 *A 6.072,0.956 6.255,1.139 0.184,0.184 10 *1 5.551,0.795 6.058,1.036 6.058,1.036 5.512,1.124 false

Text in Illustration
*A for RHD - -
*1 "TORX" Bolt - -


ii.

Remove the each bolts.


iii.

Disconnect each connector and disengage the 2 clamps and 2 claws.



d.

Remove the instrument panel reinforcement assembly.


Hide 87010 17.REMOVE AIR CONDITIONING UNIT ASSEMBLY (for Automatic Air Conditioning System)

a.

Disconnect each connector and disengage each clamp.

E246437


b.
E246443

Disengage the drain cooler hose.


c.

Remove the 3 bolts, 3 nuts and air conditioning unit assembly.

E252236E01
3.077,2.284 3.250,2.464 0.174,0.180 10 *1 1.385,0.551 1.559,0.731 0.174,0.180 10 *2 5.429,2.283 5.602,2.462 0.174,0.180 10 *1 5.766,0.452 5.939,0.632 0.174,0.180 10 *2 3.98,2.479 4.153,2.659 0.174,0.180 10 *1 3.959,0.063 4.132,0.243 0.174,0.180 10 *2 1.744,0.416 1.55,0.61 false 3.773,0.351 3.959,0.18 false 5.506,0.668 5.77,0.566 false 3.157,2.057 3.148,2.273 false 4.394,2.401 4.127,2.537 false 5.11,2.297 5.404,2.341 false

Text in Illustration
*1 Bolt *2 Nut


Hide 87010 18.REMOVE AIR CONDITIONING UNIT ASSEMBLY (for Manual Air Conditioning System)

a.

Disconnect each connector and disengage each clamp.

E246438


b.
E246443

Disengage the drain cooler hose.


c.

Remove the 3 bolts, 3 nuts and air conditioning unit assembly.

E252237E02
1.688,0.448 1.5,0.646 true 3.74,0.375 3.948,0.188 true 5.542,0.667 5.813,0.563 true 2.281,2.146 2.271,2.354 false 4.406,2.469 4.125,2.625 true 5.146,2.344 5.448,2.385 true 2.208,2.375 2.385,2.552 0.177,0.177 10 false *1 1.323,0.635 1.5,0.813 0.177,0.177 10 false *2 5.51,2.333 5.688,2.49 0.177,0.156 10 false *1 5.833,0.469 6,0.635 0.167,0.167 10 false *2 3.938,2.552 4.115,2.729 0.177,0.177 10 false *1 3.99,0.083 4.146,0.24 0.156,0.156 10 false *2

Text in Illustration
*1 Bolt *2 Nut


Hide 87010 19.REMOVE AIR CONDITIONING UNIT ASSEMBLY (w/o Air Conditioning System)

a.

Disconnect each connector and disengage each clamp.

E246439


b.
E246443

Disengage the drain cooler hose.


c.

Remove the 3 bolts, 3 nuts and air conditioning unit assembly.

E252237E02
1.688,0.448 1.5,0.646 true 3.74,0.375 3.948,0.188 true 5.542,0.667 5.813,0.563 true 2.281,2.146 2.271,2.354 false 4.406,2.469 4.125,2.625 true 5.146,2.344 5.448,2.385 true 2.208,2.375 2.385,2.552 0.177,0.177 10 false *1 1.323,0.635 1.5,0.813 0.177,0.177 10 false *2 5.51,2.333 5.688,2.49 0.177,0.156 10 false *1 5.833,0.469 6,0.635 0.167,0.167 10 false *2 3.938,2.552 4.115,2.729 0.177,0.177 10 false *1 3.99,0.083 4.146,0.24 0.156,0.156 10 false *2

Text in Illustration
*1 Bolt *2 Nut