Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM
RM2090E _59 Vehicle Exterior _060707 WINDOW / GLASS _0297766 POWER WINDOW CONTROL SYSTEM C

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  B2311  Driver Side Motor Malfunction  B2314  Passenger Side Motor Malfunction  


DESCRIPTION

The power window regulator motor is operated by the power window regulator master switch assembly and power window regulator assembly. The power window regulator motor assembly (for driver side and front passenger side) has motor, regulator and ECU functions.

These DTCs are output when the power window regulator motor assembly (for driver side and front passenger side) has a malfunction, or the power window regulator master switch assembly and power window regulator switch assembly has a malfunction.

DTC No. DTC Detection Condition Trouble Area
B2311
·

Power window regulator motor assembly malfunction (pulse sensor)

·

Power window regulator master switch assembly malfunction

·

Power window regulator assembly malfunction

·

Open or short between power window regulator motor assembly and power window regulator master switch assembly


·

Power window regulator motor assembly

·

Power window regulator master switch assembly

·

Power window regulator assembly

·

Wire harness or connector


B2314
·

Power window regulator motor assembly malfunction (pulse sensor)

·

Power window regulator switch assembly malfunction

·

Power window regulator assembly malfunction

·

Open or short between power window regulator motor assembly and power window regulator switch assembly


·

Power window regulator motor assembly

·

Power window regulator switch assembly

·

Power window regulator assembly

·

Wire harness or connector



WIRING DIAGRAM

B322617E03
5.625,1.979 5.792,2.208 0.167,0.229 10 false 4 5.625,2.354 5.792,2.583 0.167,0.229 10 false 6 5.625,2.698 5.729,2.854 0.104,0.156 10 false 2 5.625,3.052 5.729,3.208 0.104,0.156 10 false 5 4.885,1.99 5.104,2.188 0.219,0.198 10 false 14 4.885,2.354 5.042,2.552 0.156,0.198 10 false 8 4.885,2.708 5.042,2.906 0.156,0.198 10 false 1 4.885,3.063 5.042,3.281 0.156,0.219 10 false 3 4.51,2.083 4.865,2.292 0.354,0.208 10 false SGD 4.51,3.177 4.865,3.385 0.354,0.208 10 false VCC 4.531,2.802 4.875,3.01 0.344,0.208 10 false SN2 4.531,2.438 4.865,2.646 0.333,0.208 10 false SN1 5.781,2.073 6.135,2.281 0.354,0.208 10 false SGD 5.781,3.167 6.135,3.375 0.354,0.208 10 false VCC 5.781,2.802 6.125,3.01 0.344,0.208 10 false SN2 5.781,2.438 6.115,2.646 0.333,0.208 10 false SN1 5.427,3.563 5.646,3.75 0.219,0.188 10 false E5 3.625,4.427 3.875,4.646 0.25,0.219 10 false E8 3.156,1.448 3.26,1.604 0.104,0.156 10 false 2 3.167,3.344 3.271,3.5 0.104,0.156 10 false 5 3.865,1.448 3.969,1.604 0.104,0.156 10 false 2 3.865,3.344 3.969,3.5 0.104,0.156 10 false 5 2.688,1.552 3.125,1.76 0.438,0.208 10 false UART 2.771,3.448 3.135,3.656 0.365,0.208 10 false GND 4.031,1.563 4.469,1.771 0.438,0.208 10 false UART 4.031,3.448 4.396,3.656 0.365,0.208 10 false GND 0.188,0.25 0.896,0.698 0.708,0.448 12 false for LHD: 2.115,1.865 2.281,2.094 0.167,0.229 10 false 1 2.115,2.198 2.271,2.417 0.156,0.219 10 false 3 2.115,2.667 2.302,2.885 0.188,0.219 10 false 8 2.052,3.031 2.292,3.26 0.24,0.229 10 false 14 1.875,4.771 2.146,4.99 0.271,0.219 10 false F6 2.292,3.125 2.646,3.333 0.354,0.208 10 false SGD 2.292,2.333 2.646,2.542 0.354,0.208 10 false VCC 2.292,1.969 2.635,2.177 0.344,0.208 10 false SN2 2.292,2.771 2.625,2.979 0.333,0.208 10 false SN1 1.323,1.875 1.469,2.073 0.146,0.198 10 false 2 1.323,2.24 1.469,2.438 0.146,0.198 10 false 5 1.323,2.667 1.469,2.865 0.146,0.198 10 false 6 1.323,3.031 1.479,3.229 0.156,0.198 10 false 4 0.135,3.594 0.385,3.802 0.25,0.208 10 false F1 0.906,3.146 1.26,3.354 0.354,0.208 10 false SGD 0.917,2.333 1.271,2.542 0.354,0.208 10 false VCC 0.927,1.969 1.271,2.177 0.344,0.208 10 false SN2 0.927,2.771 1.26,2.979 0.333,0.208 10 false SN1 0.115,3.802 1.823,4.552 1.708,0.75 10 false Power Window Regulator Motor Assembly RH 3.625,4.615 5.354,5.271 1.729,0.656 10 false Power Window Regulator Master Switch Assembly 1.875,4.958 3.552,5.698 1.677,0.74 10 false Power Window Regulator Switch Assembly 5.458,3.76 7.156,4.104 1.698,0.344 10 false Power Window Regulator Motor Assembly LH

B322617E04
5.635,1.979 5.802,2.208 0.167,0.229 10 false 4 5.625,2.333 5.792,2.563 0.167,0.229 10 false 6 5.625,2.698 5.729,2.854 0.104,0.156 10 false 2 5.625,3.063 5.729,3.219 0.104,0.156 10 false 5 4.885,1.979 5.104,2.177 0.219,0.198 10 false 14 4.896,2.344 5.052,2.542 0.156,0.198 10 false 8 4.896,2.708 5.052,2.906 0.156,0.198 10 false 1 4.896,3.063 5.052,3.281 0.156,0.219 10 false 3 4.51,2.083 4.865,2.292 0.354,0.208 10 false SGD 4.51,3.177 4.865,3.385 0.354,0.208 10 false VCC 4.531,2.813 4.875,3.021 0.344,0.208 10 false SN2 4.531,2.438 4.865,2.646 0.333,0.208 10 false SN1 5.781,2.073 6.135,2.281 0.354,0.208 10 false SGD 5.781,3.156 6.135,3.365 0.354,0.208 10 false VCC 5.781,2.802 6.125,3.01 0.344,0.208 10 false SN2 5.781,2.427 6.115,2.635 0.333,0.208 10 false SN1 5.396,3.531 5.615,3.719 0.219,0.188 10 false F1 3.625,4.406 3.875,4.625 0.25,0.219 10 false F6 3.167,1.448 3.271,1.604 0.104,0.156 10 false 2 3.167,3.333 3.271,3.49 0.104,0.156 10 false 5 3.865,1.438 3.969,1.594 0.104,0.156 10 false 2 3.865,3.333 3.969,3.49 0.104,0.156 10 false 5 2.677,1.573 3.115,1.781 0.438,0.208 10 false UART 2.76,3.458 3.125,3.667 0.365,0.208 10 false GND 4.031,1.563 4.469,1.771 0.438,0.208 10 false UART 4.031,3.458 4.396,3.667 0.365,0.208 10 false GND 0.177,0.177 0.885,0.625 0.708,0.448 12 false for RHD: 2.104,1.854 2.271,2.083 0.167,0.229 10 false 1 2.104,2.219 2.26,2.438 0.156,0.219 10 false 3 2.104,2.667 2.292,2.885 0.188,0.219 10 false 8 2.042,3.021 2.281,3.25 0.24,0.229 10 false 14 1.875,4.74 2.146,4.958 0.271,0.219 10 false E8 2.281,3.125 2.635,3.333 0.354,0.208 10 false SGD 2.281,2.333 2.635,2.542 0.354,0.208 10 false VCC 2.281,1.969 2.625,2.177 0.344,0.208 10 false SN2 2.281,2.771 2.615,2.979 0.333,0.208 10 false SN1 1.323,1.865 1.469,2.063 0.146,0.198 10 false 2 1.323,2.229 1.469,2.427 0.146,0.198 10 false 5 1.323,2.656 1.469,2.854 0.146,0.198 10 false 6 1.323,3.021 1.479,3.219 0.156,0.198 10 false 4 0.135,3.573 0.385,3.781 0.25,0.208 10 false E5 0.906,3.146 1.26,3.354 0.354,0.208 10 false SGD 0.906,2.344 1.26,2.552 0.354,0.208 10 false VCC 0.927,1.969 1.271,2.177 0.344,0.208 10 false SN2 0.927,2.781 1.26,2.99 0.333,0.208 10 false SN1 5.396,3.708 7.104,4.458 1.708,0.75 10 false Power Window Regulator Motor Assembly RH 3.625,4.594 5.354,5.25 1.729,0.656 10 false Power Window Regulator Master Switch Assembly 1.875,4.927 3.552,5.667 1.677,0.74 10 false Power Window Regulator Switch Assembly 0.146,3.74 1.844,4.49 1.698,0.75 10 false Power Window Regulator Motor Assembly LH

CAUTION / NOTICE / HINT

NOTICE:
·

When the power window regulator master switch assembly, power window regulator switch assembly and power window regulator motor assembly is reinstalled or replaced, the power window control system must be initialized (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK DTC OUTPUT


Result
Result Proceed to
DTC B2311 is output A
DTC B2314 is output B


A

2.READ VALUE USING GTS

B

6.READ VALUE USING GTS
2.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Master Switch / Data List.


e.

According to the display on the GTS read the Data List.

Master Switch
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Current D Sensor Fail Mode1 Driver side sensor fail mode1(power of sensor malfunction) /Detected or Not Detected Not Detected -
Current D Sensor Fail Mode2 Driver side sensor fail mode2(Pulse sensor1 malfunction) /Detected or Not Detected Not Detected -
Current D Sensor Fail Mode3 Driver side sensor fail mode3(Pulse sensor2 malfunction) /Detected or Not Detected Not Detected -
Current D Sensor Fail Mode4 Driver side sensor fail mode4(Pulse direction error) /Detected or Not Detected Not Detected -
Current D Sensor Fail Mode5 Driver side sensor fail mode5(Pulse stop) /Detected or Not Detected Not Detected -
Current D Sensor Fail Mode6 Driver side sensor fail mode6(Dead zone opening direction error) /Detected or Not Detected Not Detected -

OK:

On the GTS screen, Not Detected is displayed.



Result
Result Proceed to
NG A
OK B


A

3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH - POWER WINDOW REGULATOR MOTOR)

B

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH - POWER WINDOW REGULATOR MOTOR)
a.

Disconnect the E8*1 or F6*2 power window regulator master switch assembly connector.


b.

Disconnect the E5*1 or F1*2 power window regulator motor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Current D Sensor Fail Mode 1
Tester connection Condition Specified condition
E8-3 (VCC) - E5-5 (VCC)*1 Always Below 1 Ω
E8-14 (SGD) - E5-4 (SGD)*1 Always Below 1 Ω
F6-3 (VCC) - F1-5 (VCC)*2 Always Below 1 Ω
F6-14 (SGD) - F1-4 (SGD)*2 Always Below 1 Ω

Current D Sensor Fail Mode 2
Tester connection Condition Specified condition
E8-8 (SN1) - E5-6 (SN1)*1 Always Below 1 Ω
F6-8 (SN1) - F1-6 (SN1)*2 Always Below 1 Ω

Current D Sensor Fail Mode 3
Tester connection Condition Specified condition
E8-1 (SN2) - E5-2 (SN2)*1 Always Below 1 Ω
F6-1 (SN2) - F1-2 (SN2)*2 Always Below 1 Ω

Current D Sensor Fail Mode 4
Tester connection Condition Specified condition
E8-1 (SN2) - E5-2 (SN2)*1 Always Below 1 Ω
E8-8 (SN1) - E5-6 (SN1)*1 Always Below 1 Ω
F6-1 (SN2) - F1-2 (SN2)*2 Always Below 1 Ω
F6-8 (SN1) - F1-6 (SN1)*2 Always Below 1 Ω

Current D Sensor Fail Mode 5
Tester connection Condition Specified condition
E8-1 (SN2) - E5-2 (SN2)*1 Always Below 1 Ω
E8-3 (VCC) - E5-5 (VCC)*1 Always Below 1 Ω
E8-8 (SN1) - E5-6 (SN1)*1 Always Below 1 Ω
E8-14 (SGD) - E5-4 (SGD)*1 Always Below 1 Ω
F6-1 (SN2) - F1-2 (SN2)*2 Always Below 1 Ω
F6-3 (VCC) - F1-5 (VCC)*2 Always Below 1 Ω
F6-8 (SN1) - F1-6 (SN1)*2 Always Below 1 Ω
F6-14 (SGD) - F1-4 (SGD)*2 Always Below 1 Ω

Current D Sensor Fail Mode 6
Tester connection Condition Specified condition
E8-1 (SN2) - E5-2 (SN2)*1 Always Below 1 Ω
E8-3 (VCC) - E5-5 (VCC)*1 Always Below 1 Ω
E8-8 (SN1) - E5-6 (SN1)*1 Always Below 1 Ω
E8-14 (SGD) - E5-4 (SGD)*1 Always Below 1 Ω
F6-1 (SN2) - F1-2 (SN2)*2 Always Below 1 Ω
F6-3 (VCC) - F1-5 (VCC)*2 Always Below 1 Ω
F6-8 (SN1) - F1-6 (SN1)*2 Always Below 1 Ω
F6-14 (SGD) - F1-4 (SGD)*2 Always Below 1 Ω


Standard Resistance (Check for Short):
Current D Sensor Fail Mode 1
Tester connection Condition Specified condition
E8-3 (VCC)*1 Body ground Always 10 kΩ or higher
E8-14 (SGD)*1 Body ground Always 10 kΩ or higher
F6-3 (VCC)*2 Body ground Always 10 kΩ or higher
F6-14 (SGD)*2 Body ground Always 10 kΩ or higher

Current D Sensor Fail Mode 2
Tester connection Condition Specified condition
E8-8 (SN1)*1 -Body ground Always 10 kΩ or higher
F6-8 (SN1)*2 -Body ground Always 10 kΩ or higher

Current D Sensor Fail Mode 3
Tester connection Condition Specified condition
E8-1 (SN2)*1 - Body ground Always 10 kΩ or higher
F6-1 (SN2)*2 - Body ground Always 10 kΩ or higher

Current D Sensor Fail Mode 4
Tester connection Condition Specified condition
E8-1 (SN2)*1- Body ground Always 10 kΩ or higher
E8-8 (SN1)*1 - Body ground Always 10 kΩ or higher
F6-1 (SN2)*2- Body ground Always 10 kΩ or higher
F6-8 (SN1)*2 - Body ground Always 10 kΩ or higher

Current D Sensor Fail Mode 5
Tester connection Condition Specified condition
E8-1 (SN2)*1- Body ground Always 10 kΩ or higher
E8-3 (VCC)*1 - Body ground Always 10 kΩ or higher
E8-8 (SN1)*1 - Body ground Always 10 kΩ or higher
E8-14 (SGD)*1 - Body ground Always 10 kΩ or higher
F6-1 (SN2)*2- Body ground Always 10 kΩ or higher
F6-3 (VCC)*2 - Body ground Always 10 kΩ or higher
F6-8 (SN1)*2 - Body ground Always 10 kΩ or higher
F6-14 (SGD)*2 - Body ground Always 10 kΩ or higher

Current D Sensor Fail Mode 6
Tester connection Condition Specified condition
E8-3 (VCC)*1 - Body ground Always 10 kΩ or higher
E8-8 (SN1)*1 - Body ground Always 10 kΩ or higher
E8-14 (SGD)*1 - Body ground Always 10 kΩ or higher
E8-14 (SGD)*1 - Body ground Always 10 kΩ or higher
F6-3 (VCC)*2 - Body ground Always 10 kΩ or higher
F6-8 (SN1)*2 - Body ground Always 10 kΩ or higher
F6-14 (SGD)*2 - Body ground Always 10 kΩ or higher
F6-14 (SGD)*2 - Body ground Always 10 kΩ or higher


*1: for LHD

*2: for RHD




OK

4.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY
a.

Remove the power window regulator motor assembly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR>REMOVAL ).


b.

Inspect the power window regulator motor assembly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR>INSPECTION).



OK

5.REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

NG

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY

5.REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
a.

Temporarily replace the power window regulator master switch assembly with a new or normally functioning one (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL).


b.

Check the power window regulator master switch assembly operates (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>OPERATION CHECK).

OK:

Driver side door power window operates normally.



Result
Result Proceed to
Does not operate A
Operate B


A

REPLACE POWER WINDOW REGULATOR ASSEMBLY

B

END

6.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Master Switch / Data List.


e.

According to the display on the GTS read the Data List.

Master Switch
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Current P Sensor Fail Mode1 Front passenger side sensor fail mode1(power of sensor malfunction) /Detected or Not Detected Not Detected -
Current P Sensor Fail Mode2 Front passenger side sensor fail mode2(Pulse sensor1 malfunction) /Detected or Not Detected Not Detected -
Current P Sensor Fail Mode3 Front passenger side sensor fail mode3(Pulse sensor2 malfunction) /Detected or Not Detected Not Detected -
Current P Sensor Fail Mode4 Front passenger side sensor fail mode4(Pulse direction error) /Detected or Not Detected Not Detected -
Current P Sensor Fail Mode5 Front passenger side sensor fail mode5(Pulse stop) /Detected or Not Detected Not Detected -
Current P Sensor Fail Mode6 Front passenger side sensor fail mode6(Dead zone opening direction error) /Detected or Not Detected Not Detected -

OK:

On the GTS screen, Not Detected is displayed.



Result
Result Proceed to
NG A
OK B


A

7.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH - POWER WINDOW REGULATOR MOTOR)

B

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH - POWER WINDOW REGULATOR MOTOR)
a.

Disconnect the F6*1 or E8*2 power window regulator master switch assembly connector.


b.

Disconnect the F1*1 or E5*2 power window regulator motor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Current P Sensor Fail Mode 1
Tester connection Condition Specified condition
F6-3 (VCC) - F1-5 (VCC)*1 Always Below 1 Ω
F6-14 (SGD) - F1-4 (SGD)*1 Always Below 1 Ω
E8-3 (VCC) - E5-5 (VCC)*2 Always Below 1 Ω
E8-14 (SGD) - E5-4 (SGD)*2 Always Below 1 Ω

Current P Sensor Fail Mode 2
Tester connection Condition Specified condition
F6-8 (SN1) - F1-6 (SN1)*1 Always Below 1 Ω
E8-8 (SN1) - E5-6 (SN1)*2 Always Below 1 Ω

Current P Sensor Fail Mode 3
Tester connection Condition Specified condition
F6-1 (SN2) - F1-2 (SN2)*1 Always Below 1 Ω
E8-1 (SN2) - E5-2 (SN2)*2 Always Below 1 Ω

Current P Sensor Fail Mode 4
Tester connection Condition Specified condition
F6-1 (SN2) - F1-2 (SN2)*1 Always Below 1 Ω
F6-8 (SN1) - F1-6 (SN1)*1 Always Below 1 Ω
E8-1 (SN2) - E5-2 (SN2)*2 Always Below 1 Ω
E8-8 (SN1) - E5-6 (SN1)*2 Always Below 1 Ω

Current P Sensor Fail Mode 5
Tester connection Condition Specified condition
F6-1 (SN2) - F1-2 (SN2)*1 Always Below 1 Ω
F6-3 (VCC) - F1-5 (VCC)*1 Always Below 1 Ω
F6-8 (SN1) - F1-6 (SN1)*1 Always Below 1 Ω
F6-14 (SGD) - F1-4 (SGD)*1 Always Below 1 Ω
E8-1 (SN2) - E5-2 (SN2)*2 Always Below 1 Ω
E8-3 (VCC) - E5-5 (VCC)*2 Always Below 1 Ω
E8-8 (SN1) - E5-6 (SN1)*2 Always Below 1 Ω
E8-14 (SGD) - E5-4 (SGD)*2 Always Below 1 Ω

Current P Sensor Fail Mode 6
Tester connection Condition Specified condition
F6-1 (SN2) - F1-2 (SN2)*1 Always Below 1 Ω
F6-3 (VCC) - F1-5 (VCC)*1 Always Below 1 Ω
F6-8 (SN1) - F1-6 (SN1)*1 Always Below 1 Ω
F6-14 (SGD) - F1-4 (SGD)*1 Always Below 1 Ω
E8-1 (SN2) - E5-2 (SN2)*2 Always Below 1 Ω
E8-3 (VCC) - E5-5 (VCC)*2 Always Below 1 Ω
E8-8 (SN1) - E5-6 (SN1)*2 Always Below 1 Ω
E8-14 (SGD) - E5-4 (SGD)*2 Always Below 1 Ω


Standard Resistance (Check for Short):
Current P Sensor Fail Mode 1
Tester connection Condition Specified condition
F6-3 (VCC)*1 - Body ground Always 10 kΩ or higher
F6-14 (SGD)*1 - Body ground Always 10 kΩ or higher
E8-3 (VCC)*2 - Body ground Always 10 kΩ or higher
E8-14 (SGD)*2 - Body ground Always 10 kΩ or higher

Current P Sensor Fail Mode 2
Tester connection Condition Specified condition
F6-8 (SN1)*1 - Body ground Always 10 kΩ or higher
E8-8 (SN1)*2 - Body ground Always 10 kΩ or higher

Current P Sensor Fail Mode 3
Tester connection Condition Specified condition
F6-1 (SN2)*1 - Body ground Always 10 kΩ or higher
E8-1 (SN2)*2 - Body ground Always 10 kΩ or higher

Current P Sensor Fail Mode 4
Tester connection Condition Specified condition
F6-1 (SN2)*1 - Body ground Always 10 kΩ or higher
F6-8 (SN1)*1 - Body ground Always 10 kΩ or higher
E8-1 (SN2)*2 - Body ground Always 10 kΩ or higher
E8-8 (SN1)*2 - Body ground Always 10 kΩ or higher

Current P Sensor Fail Mode 5
Tester connection Condition Specified condition
F6-1 (SN2)*1 - Body ground Always 10 kΩ or higher
F6-3 (VCC)*1 - Body ground Always 10 kΩ or higher
F6-8 (SN1)*1 - Body ground Always 10 kΩ or higher
F6-14 (SGD)*1 - Body ground Always 10 kΩ or higher
E8-1 (SN2)*2 - Body ground Always 10 kΩ or higher
E8-3 (VCC)*2 - Body ground Always 10 kΩ or higher
E8-8 (SN1)*2 - Body ground Always 10 kΩ or higher
E8-14 (SGD)*2 - Body ground Always 10 kΩ or higher

Current P Sensor Fail Mode 6
Tester connection Condition Specified condition
F6-1 (SN2)*1 - Body ground Always 10 kΩ or higher
F6-3 (VCC)*1 - Body ground Always 10 kΩ or higher
F6-8 (SN1)*1 - Body ground Always 10 kΩ or higher
F6-14 (SGD)*1 - Body ground Always 10 kΩ or higher
E8-1 (SN2)*2 - Body ground Always 10 kΩ or higher
E8-3 (VCC)*2 - Body ground Always 10 kΩ or higher
E8-8 (SN1)*2 - Body ground Always 10 kΩ or higher
E8-14 (SGD)*2 - Body ground Always 10 kΩ or higher


*1: for LHD

*2: for RHD




OK

8.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY
a.

Remove the power window regulator motor assembly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR>REMOVAL ).


b.

Inspect the power window regulator motor assembly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR>INSPECTION).



OK

9.REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY

NG

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY

9.REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY
a.

Temporarily replace the power window regulator switch assembly with a new or normally functioning one (See page Vehicle Exterior>WINDOW / GLASS>FRONT PASSENGER SIDE POWER WINDOW SWITCH>REMOVAL).


b.

Check the power window regulator switch assembly operates (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>OPERATION CHECK).

OK:

Front passenger side door power window operates normally.



Result
Result Proceed to
Does not operate A
Operate B


A

10.REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

B

END

10.REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
a.

Temporarily replace the power window regulator master switch assembly with a new or normally functioning one (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL).


b.

Check the power window regulator master switch assembly operates (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>INSPECTION).

OK:

Driver side door power window operates normally.



Result
Result Proceed to
Does not operate A
Operate B


A

REPLACE POWER WINDOW REGULATOR ASSEMBLY

B

END