Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM
RM2090E _59 Vehicle Exterior _060711 LIGHTING (EXT) _0297816 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Rear Fog Light Circuit  


DESCRIPTION

The main body ECU (network gateway ECU) receives headlight dimmer switch assembly information signals, and illuminates the rear fog light.

WIRING DIAGRAM

E252208E02
5.406,4.135 5.573,4.323 0.167,0.188 10 false 3 5.323,4.344 5.656,4.552 0.333,0.208 10 false A73 3.698,2.167 3.792,2.323 0.094,0.156 10 false 1 2.438,0.802 2.552,0.958 0.115,0.156 10 false 1 2.438,1.115 2.552,1.271 0.115,0.156 10 false 3 3.063,1.115 3.177,1.271 0.115,0.156 10 false 5 3.063,0.792 3.177,0.948 0.115,0.156 10 false 2 5.417,2.469 5.531,2.625 0.115,0.156 10 false 7 3.677,0.688 3.865,0.844 0.188,0.156 10 false 26 2.5,2.063 3.167,2.292 0.667,0.229 10 false RR FOG 2.531,1.51 3.177,1.75 0.646,0.24 10 false RR FOG 3.667,2.365 3.854,2.51 0.188,0.146 10 false 3E 5.656,2.677 6.104,2.979 0.448,0.302 10 false TRLY 5.344,2.688 5.573,2.833 0.229,0.146 10 false MB 3.677,0.885 3.875,1.031 0.198,0.146 10 false 3C 4.646,1.042 4.958,1.188 0.313,0.146 10 false TAIL 4.646,2.958 4.958,3.104 0.313,0.146 10 false TAIL 3.958,3.365 5.615,4 1.656,0.635 10 false Instrument Panel Junction Block Assembly 5.271,4.896 6.958,5.563 1.688,0.667 10 false Main Body ECU (Network Gateway ECU) 0.865,1.865 1.667,2.188 0.802,0.323 10 false from Battery 2.385,2.99 2.5,3.146 0.115,0.156 10 false 3 1.281,3.01 1.396,3.167 0.115,0.156 10 false 2 1.125,3.365 1.354,3.51 0.229,0.146 10 false H2 1.115,3.531 2.688,4.198 1.573,0.667 10 false Rear Light Assembly (Rear Fog Light)

CAUTION / NOTICE / HINT

HINT:

Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK OPERATION (TAILLIGHT)
a.

Check the operation of the taillight.

OK:

The taillight operates normally.




OK

2.PERFORM ACTIVE TEST USING GTS

NG

2.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Check that the relay operates.


Main Body
Tester Display Test Part Control Range Diagnostic Note
Rear Fog Light Relay Rear fog light relay ON/OFF Light control switch is in TAIL position

OK:

Rear fog light relay operates (Rear fog lights come on).



OK

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU)

NG

3.INSPECT RR FOG RELAY
3.INSPECT RR FOG RELAY
a.

Remove the RR FOG relay from the engine room relay block.


b.


OK

4.INSPECT REAR FOG LIGHT BULB (REAR LIGHT ASSEMBLY)

NG

REPLACE RR FOG RELAY

4.INSPECT REAR FOG LIGHT BULB (REAR LIGHT ASSEMBLY)
a.

Remove the rear fog light bulb (See page Vehicle Exterior>LIGHTING (EXT)>REAR LIGHT ASSEMBLY>DISASSEMBLY).


b.

Inspect the rear fog light bulb (See page Vehicle Exterior>LIGHTING (EXT)>REAR LIGHT ASSEMBLY>INSPECTION).



OK

5.CHECK HARNESS AND CONNECTOR (BATTERY - RR FOG RELAY)

NG

5.CHECK HARNESS AND CONNECTOR (BATTERY - RR FOG RELAY)
a.

Measure the voltage according to the value(s) in the table below.


Standard Voltage:
Tester Connection Switch Condition Specified Condition
Relay terminal 2 - Body ground Light control switch off → tail Below 1 V → 11 to 14 V
Relay terminal 5 - Body ground Always 11 to 14 V



OK

6.CHECK HARNESS AND CONNECTOR (RR FOG RELAY - REAR LIGHT ASSEMBLY)

NG

8.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
6.CHECK HARNESS AND CONNECTOR (RR FOG RELAY - REAR LIGHT ASSEMBLY)
a.

Disconnect the H2 rear light assembly connector.


b.

Measure the resistance according to the value(s) in the table below.


Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
Relay terminal 3 - H2-2 Light control switch off → tail Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
Relay terminal 3 - Body ground Always 10 kΩ or higher



OK

7.CHECK HARNESS AND CONNECTOR (RR FOG RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (RR FOG RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the A73 instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.


Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
Relay terminal 1 - A73-3 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
Relay terminal 1 - Body ground Always 10 kΩ or higher



OK

8.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Remove the main body ECU (network gateway ECU) from the instrument panel junction block assembly.

U190423E02
2.563,2.052 2.563,2.281 true 0.198,0.073 0.385,0.229 0.188,0.156 10 false *a 1.76,0.208 2.052,0.365 0.292,0.156 10 false 3C 5.188,0.188 5.479,0.344 0.292,0.156 10 false 3E 3.469,1.51 3.76,1.667 0.292,0.156 10 false MB 2.406,2.354 2.896,2.594 0.49,0.24 10 false TRLY

Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


c.

Measure the voltage according to the value(s) in the table below.


Standard Voltage:
Tester Connection Condition Specified Condition
3C-26 - Battery negative (-) terminal Connect a positive (+) lead from the battery → 3E-1
Connect a negative (-) lead from the battery → MB-7 (TRLY)
11 to 14 V



OK

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY