Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR AXLE HUB BOLT › from 2017.03
RM2090E _52 Drivetrain _060678 AXLE AND DIFFERENTIAL _0297587 REAR AXLE HUB BOLT A

AXLE AND DIFFERENTIAL  REAR AXLE HUB BOLT  REPLACEMENT  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.REMOVE REAR WHEEL

Hide 47810A 2.SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY

Hide 42312E 4.REMOVE REAR AXLE HUB BOLT LH

a.

Using SST, remove the rear axle hub bolt LH from rear axle hub and bearing assembly LH.

SST
09960-20010  (09961-02010, 09961-02060)

C265373E03
0.802,0.5 1.073,0.5 1.073,0.5 1.073,0.865 false 1.156,0.229 1.427,0.229 1.427,0.229 1.427,0.896 false 1.698,1.781 1.427,1.781 1.427,1.781 1.427,1.531 false 0.427,1.552 0.427,1.281 0.427,1.281 0.646,1.281 false 0.427,1.354 0.646,1.354 false 5.667,2.49 5.396,2.49 5.396,2.49 5.115,2.125 false 6.469,0.479 6.75,0.479 false 0.646,0.427 0.813,0.583 0.167,0.156 10 false *1 1.01,0.156 1.177,0.313 0.167,0.156 10 false *3 1.719,1.698 1.885,1.854 0.167,0.156 10 false *2 0.344,1.573 0.51,1.729 0.167,0.156 10 false *4 5.729,2.396 6.104,2.552 0.375,0.156 10 false SST 6.781,0.396 6.979,0.552 0.198,0.156 10 false *a

Text in illustration
*1 Nut *2 Body
*3 Claw *4 SST (Spacer B)
*a Place a Wrench Here - -
V100135

Molybdenum Grease
V100136

Turn

CAUTION:

Before working, apply molybdenum grease to the bolt threads and bolt tip of SST.


NOTICE:
·

Install SST so that claw and body are parallel

·

Make sure to tie the string of SST to the vehicle to prevent SST from dropping.

·

Do not damage the parking brake plate sub-assembly.

·

Do not damage the rear axle carrier.

·

Do not damage the rear axle hub and bearing.




Hide 42312E 5.INSTALL REAR AXLE HUB BOLT LH

a.
C123492E02
2.146,0.146 2.583,0.458 true 2.802,0.802 3.24,1.104 true 3.219,1.125 3.385,1.292 0.167,0.167 10 false *1 1.948,0.042 2.115,0.208 0.167,0.167 10 false *2 2.031,1.604 2.198,1.771 0.167,0.167 10 false *a 0.323,1.688 0.49,1.854 0.167,0.167 10 false *b

Set a new axle hub bolt onto the rear axle hub and bearing, and tighten the nut (M12 x P1.25mm (0.0492 in.)) through the washer plate to install the axle hub bolt.

Text in Illustration
*1 Nut
*2 Washer
*a Turn
*b Hold

NOTICE:

Install the nuts to prevent damage to the rear axle hub bolts.



Hide 47810A 7.INSTALL REAR DISC BRAKE CALIPER ASSEMBLY

Hide 8.INSTALL REAR WHEEL

Torque:
120 N*m (1224 kgf*cm, 89 ft.*lbf)