Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2019.03
RM2090E _54 Brake _060684 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0297617 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1241  Low or High Power Supply Voltage  


DESCRIPTION

If a malfunction is detected in the power supply circuit, the skid control ECU (brake actuator assembly) stores this DTC and the fail-safe function prohibits ABS operation.

This DTC is stored when the +BS terminal voltage meets one of the DTC detection conditions due to a malfunction in the power supply or charging circuit such as the battery or alternator circuit, etc.

The DTC is canceled when the +BS terminal voltage returns to normal.

DTC No. DTC Detection Condition Trouble Area
C1241 Any of the following is detected:
1.

The vehicle speed is 6 km/h (4 mph) or more and the +BS terminal voltage (soft low voltage) is 9.6 V or less for 1 second or more.

2.

The vehicle speed is 6 km/h (4 mph) or more and the +BS terminal voltage (hard low voltage) is 6.9 V or less for 1 second or more.

3.

The vehicle speed is 15 km/h (9 mph) or more, the +BS terminal voltage is 9.6 V or more, the skid control ECU (brake actuator assembly) turns on more than one valve at the same time within a short period of time and the valve relay supply voltage drop exceeds the threshold.*


·

ABS NO. 2 fuse

·

ECU IG1 fuse

·

Battery

·

Charging system

·

Power source circuit

·

Ground circuit

·

Internal power supply circuit of the skid control ECU



*: The skid control ECU (brake actuator assembly) monitors the resistance of the power source line at the +BS terminal. A malfunction is detected when an abnormality occurs in the +BS terminal wire harness or its connection and the skid control ECU (brake actuator assembly) determines that the wiring resistance at the +BS terminal exceeds the standard resistance.

WIRING DIAGRAM

C261860E03
0.427,0.5 1.917,0.844 1.49,0.344 10 false from Battery 0.333,1.01 1.688,1.323 1.354,0.313 10 false from IG1 Circuit 2.438,0.667 3.344,0.833 0.906,0.167 10 false ABS NO.2 2.469,1.167 3.51,1.344 1.042,0.177 10 false ECU IG1 4.375,0.51 5.167,0.667 0.792,0.156 10 false +BS 4.375,1.021 5.167,1.177 0.792,0.156 10 false IG1 4.375,1.563 5.198,1.729 0.823,0.167 10 false GND1 4.365,2.115 5.073,2.281 0.708,0.167 10 false GND2 4.125,0.427 4.813,0.604 0.688,0.177 10 false 25 4.125,0.927 4.781,1.094 0.656,0.167 10 false 28 4.125,1.469 5,1.635 0.875,0.167 10 false 38 4.125,2.021 4.813,2.188 0.688,0.167 10 false 13 4.198,2.875 4.833,3.083 0.635,0.208 10 false A5 4.198,3.052 6.125,3.625 1.927,0.573 10 false Skid Control ECU (Brake Actuator Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform VSC sensor neutral memorization.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK BATTERY
a.

Check the battery voltage.

Standard Voltage:

11 to 14 V




OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

NG

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.
U147145E01
0.073,0.083 0.239,0.233 0.166,0.151 10 *a 0.655,0.47 0.655,0.867 false 1.202,0.478 1.202,0.923 false 2.742,0.487 2.742,0.862 false 0.503,0.289 0.844,0.440 0.341,0.151 10 +BS 1.061,0.301 1.382,0.451 0.321,0.151 10 IG1 2.604,0.314 3.082,0.465 0.479,0.151 10 GND1 1.598,0.198 1.854,0.348 0.256,0.151 10 A5

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A5-25 (+BS) - Body ground Always 11 to 14 V
A5-25 (+BS) - A5-38 (GND1) Always 11 to 14 V
A5-28 (IG1) - Body ground Ignition switch ON 11 to 14 V
A5-28 (IG1) - A5-38 (GND1) Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))

Result:
Result Proceed to
OK A
NG (for +BS circuit) B
NG (for IG1 circuit) C




A

3.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

B

REPAIR OR REPLACE HARNESS OR CONNECTOR (+BS CIRCUIT)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)

3.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.
U147144E01
0.073,0.083 0.239,0.233 0.166,0.151 10 *a 2.742,0.487 2.742,0.862 false 2.518,0.314 2.984,0.465 0.467,0.151 10 GND1 1.598,0.198 1.854,0.348 0.256,0.151 10 A5

Turn the ignition switch off.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A5-38 (GND1) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))



OK

4.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

4.RECONFIRM DTC
a.

Reconnect the skid control ECU (brake actuator assembly) connector.



c.

Turn the ignition switch off.


d.

Start the engine.


e.

Perform a road test.


f.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Result:
Result Proceed to
DTC C1241 is not output. A
DTC C1241 is output. B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE




A

B