Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) › 2011.11–2015.08
RM19Y0E _56 Audio / Visual / Telematics _003000 AUDIO / VIDEO _0015166 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  Illumination Circuit  


DESCRIPTION

Power is supplied to the stereo component tuner assembly illumination when the light control switch is in the tail or head position.

WIRING DIAGRAM

E232728E02
4.948,2.823 6.573,3.188 1.625,0.365 10 STEREO COMPONENT TUNER ASSEMBLY 5.063,0.344 5.51,0.51 0.448,0.167 10 ILM+ 4.729,0.354 5.177,0.521 0.448,0.167 10 E4 4.729,2.427 5.177,2.594 0.448,0.167 10 E5 4.208,1.396 4.521,1.563 0.313,0.167 10 E32 3.24,1.396 3.552,1.563 0.313,0.167 10 z3 3.24,2.427 3.552,2.594 0.313,0.167 10 z3 4.208,2.427 4.521,2.594 0.313,0.167 10 E32 4.729,0.156 4.917,0.323 0.188,0.167 10 10 3.802,0.479 3.99,0.646 0.188,0.167 10 * 4.563,2.406 4.75,2.573 0.188,0.167 10 * 0.26,0.365 2.281,1 2.021,0.635 10 from Headlight Dimmer Switch Assembly (Light Control Switch) 0.583,2.781 2.969,3.208 2.385,0.427 10 STEERING WHEEL SUB-ASSEMBLY (STEERING PAD SWITCH) 0.26,3.427 2.042,3.74 1.781,0.313 10 *: w/ Steering Pad Switch 3.344,2.781 4.5,3.198 1.156,0.417 10 SPIRAL CABLE SUB-ASSEMBLY 3.677,2.333 4.042,2.5 0.365,0.167 10 EAU 4.781,2.229 4.906,2.396 0.125,0.167 10 6 4.292,2.229 4.417,2.396 0.125,0.167 10 5 3.271,2.229 3.396,2.396 0.125,0.167 10 5 3.677,1.302 4.042,1.469 0.365,0.167 10 IL+2 4.292,1.208 4.417,1.375 0.125,0.167 10 2 3.271,1.208 3.396,1.375 0.125,0.167 10 2 5.052,2.427 5.438,2.583 0.385,0.156 10 EAU

PROCEDURE

1.CHECK ILLUMINATION
a.

Check if the illumination for the stereo component tuner assembly, heater control switch or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the head or tail position.

Result:
Result Proceed to
Illumination comes on for all components except stereo component tuner assembly. A
Illumination comes on for all components except steering wheel sub-assembly (steering pad switch). B
No illumination comes on (stereo component tuner assembly, hazard switch, etc.). C




A

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE - STEREO COMPONENT TUNER)

B

3.INSPECT STEERING WHEEL SUB-ASSEMBLY (STEERING PAD SWITCH)

C

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE - STEREO COMPONENT TUNER)
a.
E230878C03
1.427,0.99 1.885,1.271 0.458,0.281 2.167,2.208 2.365,2.615 true 2.292,2.656 2.625,2.833 0.333,0.177 10 ILM+ 1.563,1.052 1.885,1.208 0.323,0.156 10 E4 0.406,0.323 0.635,0.479 0.229,0.156 10 *a
*a Front view of wire harness connector
(to Stereo Component Tuner Assembly)


Disconnect the E4 stereo component tuner assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E4-10 (ILM+) - Body ground Light control switch tail or head 11 to 14 V


Result:
Proceed to
OK
NG




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STEERING WHEEL SUB-ASSEMBLY (STEERING PAD SWITCH)
a.

Remove the steering wheel sub-assembly.

Click hereSteering>STEERING COLUMN>STEERING WHEEL>REMOVAL


b.

Inspect the steering wheel sub-assembly.

Click hereSteering>STEERING COLUMN>STEERING WHEEL>INSPECTION

Result:
Proceed to
OK
NG




OK

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING WHEEL SUB-ASSEMBLY

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly.

Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>DISASSEMBLY


b.

Inspect the spiral cable sub-assembly.

Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>INSPECTION

Result:
Proceed to
OK
NG




OK

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - STEREO COMPONENT TUNER)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - STEREO COMPONENT TUNER)
a.

Disconnect the E5 stereo component tuner assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition
E32-5 (EAU) - E5-6 (EAU) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Switch Condition Specified Condition
E32-5 (EAU) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE -POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR