Home › Brake › BRAKE SYSTEM (OTHER) › 2NR-VE BRAKE PEDAL(for LHD) › from 2015.08
RM19Y0E _54 Brake _002993 BRAKE SYSTEM (OTHER) _0193170 2NR-VE BRAKE PEDAL(for LHD) A

BRAKE SYSTEM (OTHER)  2NR-VE BRAKE PEDAL(for LHD)  INSTALLATION  


PROCEDURE

Hide 55106 1.INSTALL BRAKE PEDAL SUPPORT SUB-ASSEMBLY (for Automatic Transmission)

a.
C332240N01
1.885,1.323 2.042,1.521 0.156,0.198 10 false B 1.948,0.25 2.104,0.448 0.156,0.198 10 false A

Temporarily install the brake mounting bracket with the bolt A.


b.

Temporarily install bolt B.


c.
C334508

Hook and hold the brake pedal support sub-assembly onto the bolt B used for the temporary installation.


d.

Install the brake pedal support sub-assembly with the bolt B and 4 nuts.

Torque:
Bolt B : 21 N*m (214 kgf*cm, 15 ft.*lbf)
Nut : 12.8 N*m (131 kgf*cm, 9 ft.*lbf)


e.

Tighten the bolt A.

Torque:
31 N*m (316 kgf*cm, 23 ft.*lbf)


Hide 55106 2.INSTALL BRAKE PEDAL SUPPORT SUB-ASSEMBLY (for Manual Transmission)

a.
C337751N01
1.927,0.302 2.125,0.552 0.198,0.25 10 false A

Temporarily install the brake mounting bracket with the bolt A.


b.
C337748

Install the brake support sub-assembly as shown the illustration.


c.

Install the 3 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


d.

Connect the connector to the clutch start switch assembly.


e.

Tighten the bolt A.

Torque:
31 N*m (316 kgf*cm, 23 ft.*lbf)


Hide 47264D 3.CONNECT BRAKE MASTER CYLINDER PUSH ROD CLEVIS (for Automatic Transmission)

Hide 31481 4.CONNECT NO. 1 CLUTCH RELEASE TUBE (for Manual Transmission)

Hide 5.CONNECT NO. 1 CLUTCH RESERVOIR HOSE (for Manual Transmission)

Hide 84345 6.INSTALL STOP LIGHT SWITCH MOUNTING ADJUSTER

a.

Install the stop light switch mounting adjuster onto the pedal support sub-assembly.


Hide 84340 7.INSTALL STOP LIGHT SWITCH ASSEMBLY

a.
C133150C02
1.313,0.583 1.385,0.198 1.385,0.198 1.479,0.198 false 0.75,1.271 0.948,1.583 0.948,1.583 0.948,1.698 false 2.146,1.396 2.146,1.615 false 1.521,0.104 2.073,0.521 0.552,0.417 10 *1 2.052,1.635 2.49,2.063 0.438,0.427 10 *3 0.854,1.708 1.417,2.146 0.563,0.438 10 *2
*1 Adjuster
*2 Cushion
*3 Stop light switch assembly


Insert the stop light switch assembly into the adjuster until it just touches the stop light switch cushion.

NOTICE:

Do not depress the brake pedal.



b.
C338367C01
0.646,0.885 0.729,0.219 0.729,0.219 0.896,0.219 false 1.75,0.583 1.833,0.25 1.833,0.25 2,0.25 false 0.958,0.156 1.271,0.313 0.313,0.156 10 false *1 2.042,0.177 2.354,0.333 0.313,0.156 10 false *2 0.583,1.917 0.896,2.073 0.313,0.156 10 false *a
*1 Shaft
*2 Stop light switch assembly
*a 0.2 to 2.8 mm
(0.008 to 0.110 in.)


Turn the stop light switch assembly 90° clockwise to install it.

NOTICE:

Do not depress the brake pedal.



c.

Check the stop light switch assembly clearance.

Stop light switch clearance:

0.2 to 2.8 mm (0.008 to 0.110 in.)



d.

Connect the connector to the stop light switch assembly.


Hide 44610 8.INSTALL BRAKE BOOSTER ASSEMBLY (for Manual Transmission)

Hide 9.BLEED CLUTCH LINE (for Manual Transmission)

Hide 10.CHECK FLUID LEVEL IN RESERVOIR (for Manual Transmission)

Hide 11.CHECK FOR CLUTCH FLUID LEAK (for Manual Transmission)

Hide 31301 12.INSPECT AND ADJUST CLUTCH PEDAL SUB-ASSEMBLY (for Manual Transmission)

Hide 47101 13.INSPECT AND ADJUST BRAKE PEDAL SUB-ASSEMBLY

Hide 84520 14.INSTALL CLUTCH START SWITCH ASSEMBLY (for Manual Transmission)

Hide 55545 15.INSTALL FUSE BOX OPENING COVER (for Manual Transmission)

Hide 45250 16.INSTALL STEERING COLUMN ASSEMBLY (for Manual Transmission)

Hide 45287 17.INSTALL LOWER STEERING COLUMN COVER (for Automatic Transmission)

Hide 83100 18.INSTALL COMBINATION METER ASSEMBLY