Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2015.08
RM19Y0E _57 Power Source / Network _003004 NETWORKING _0015181 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Skid Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Skid Control ECU Communication Stop Mode Either condition is met:
·

"VSC/ABS" is not displayed on the CAN Bus Check screen of the GTS or Techstream

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Skid Control ECU Communication Stop Mode" in "DTC Combination Table" are output

Click here(Click here)


·

Skid control ECU (brake actuator assembly) branch line or connector

·

Power source circuit of skid control ECU (brake actuator assembly)

·

Skid control ECU (brake actuator assembly) ground circuit

·

Skid control ECU (brake actuator assembly)



WIRING DIAGRAM

C329962E02
5.083,0.938 4.604,0.281 4.604,0.281 4.438,0.281 false 4.75,2.448 5.177,3.354 5.177,3.354 5.344,3.354 false 1.823,4.396 4.698,4.792 2.875,0.396 10 false Skid Control ECU (Brake Actuator Assembly) 1.698,5.083 3.646,5.49 1.948,0.406 10 false : CAN Main Bus Line (CANH) 1.719,5.385 3.667,5.792 1.948,0.406 10 false : CAN Main Bus Line (CANL) 4.719,5.083 6.667,5.49 1.948,0.406 10 false : CAN Branch Line (CANH) 4.719,5.365 6.667,5.771 1.948,0.406 10 false : CAN Branch Line (CANL) 4.854,4.198 5.802,4.594 0.948,0.396 10 false Trouble Area 3.396,3.438 3.906,3.781 0.51,0.344 10 false GND1 3.385,3.854 3.896,4.198 0.51,0.344 10 false GND2 3.875,3.323 4.146,3.615 0.271,0.292 10 false 25 3.885,3.75 4.156,4.042 0.271,0.292 10 false 1 2.479,2.26 2.99,2.604 0.51,0.344 10 false CANH 3.125,2.969 3.635,3.313 0.51,0.344 10 false CANL 2.406,3.188 2.917,3.531 0.51,0.344 10 false +BM 2.417,3.573 2.927,3.917 0.51,0.344 10 false +BS 2.417,3.979 2.927,4.323 0.51,0.344 10 false +IG 1.469,3.323 1.979,3.625 0.51,0.302 10 false ABS 1.438,3.719 1.948,4.063 0.51,0.344 10 false ABS2 1.365,4.135 2.052,4.438 0.688,0.302 10 false ECU-IG1 1.5,4.396 2.01,4.719 0.51,0.323 10 false A13 5.24,0.24 5.75,0.563 0.51,0.323 10 false DLC3 0.219,2.521 0.729,2.844 0.51,0.323 10 false A24 5.844,2.5 7.104,3.198 1.26,0.698 10 false Combination Meter Assembly 5.406,3.271 6.802,4.021 1.396,0.75 10 false Main Body ECU (Fuse Block Assembly) 2.521,0.188 4.521,0.688 2,0.5 10 false No. 1 CAN Junction Connector 0.219,2.698 0.729,3.021 0.51,0.323 10 false ECM 2.156,3.063 2.427,3.354 0.271,0.292 10 false 13 2.156,3.865 2.427,4.156 0.271,0.292 10 false 12 2.156,3.458 2.5,3.75 0.344,0.292 10 false 38 3.292,2.729 3.563,3.021 0.271,0.292 10 false 10 2.677,2.729 2.948,3.021 0.271,0.292 10 false 22 2.667,2.958 3.177,3.302 0.51,0.344 10 false CANH 3.292,2.26 3.802,2.604 0.51,0.344 10 false CANL 3.302,2.469 3.573,2.76 0.271,0.292 10 false 40 2.688,2.469 2.958,2.76 0.271,0.292 10 false 39 0.583,1.896 1.094,2.24 0.51,0.344 10 false 120 Ω 6.427,1.917 6.938,2.26 0.51,0.344 10 false 120 Ω

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON, wait at least 5 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the A13 skid control ECU (brake actuator assembly) connector.


c.
C330019C16
1.51,0.25 1.927,0.5 0.417,0.25 2.292,0.323 2.125,0.323 2.125,0.323 2.021,0.99 true 2.417,1.917 2.25,1.917 2.25,1.917 2.01,1.219 true 0.115,0.094 0.427,0.344 0.313,0.25 10 false *a 1.594,0.292 1.99,0.583 0.396,0.292 10 false A13 2.479,1.833 2.99,2.135 0.51,0.302 10 false CANH 2.365,0.26 2.875,0.563 0.51,0.302 10 false CANL
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A13-22 (CANH) - A13-10 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - ECM)
2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C330019C17
1.51,0.25 1.927,0.5 0.417,0.25 0.51,0.427 0.677,0.427 0.677,0.427 0.844,1.01 true 0.51,1.865 0.677,1.865 0.677,1.865 0.844,1.365 true 0.115,0.094 0.427,0.344 0.313,0.25 10 false *a 1.594,0.292 1.99,0.583 0.396,0.292 10 false A13 0.083,0.344 0.594,0.646 0.51,0.302 10 false GND2 0.083,1.781 0.594,2.083 0.51,0.302 10 false GND1
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A13-25 (GND1) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
A13-1 (GND2) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.
C330019C18
1.51,0.25 1.927,0.5 0.417,0.25 2.781,0.396 2.615,0.396 2.615,0.396 2.469,0.99 true 2.875,1.938 2.708,1.938 2.708,1.938 2.51,1.354 true 2.542,0.135 2.375,0.135 2.375,0.135 2.24,1 true 0.115,0.094 0.427,0.344 0.313,0.25 10 false *a 1.583,0.292 1.979,0.583 0.396,0.292 10 false A13 2.917,1.854 3.375,2.135 0.458,0.281 10 false +BS 2.854,0.313 3.365,0.615 0.51,0.302 10 false +BM 2.604,0.052 3.115,0.354 0.51,0.302 10 false +IG
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A13-13 (+BM)- Body ground Always 11 to 14 V
A13-38 (+BS)- Body ground Always 11 to 14 V
A13-12 (+IG)- Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - ECM)
a.

Disconnect the A24 ECM connector.


b.
C333534C02
1.5,2.417 1.917,2.667 0.417,0.25 1.5,0.417 1.917,0.667 0.417,0.25 0.979,3.385 0.802,2.594 0.802,2.594 0.635,2.594 true 0.844,3.5 0.76,4.333 0.76,4.333 0.594,4.333 true 2.031,1.146 2.281,0.479 2.281,0.479 2.448,0.479 true 2.021,1.354 2.271,2.104 2.271,2.104 2.438,2.104 true 0.094,0.083 0.5,0.417 0.406,0.333 10 false *a 0.083,2.271 0.49,2.604 0.406,0.333 10 false *b 1.583,2.458 1.99,2.792 0.406,0.333 10 false A24 1.583,0.458 1.99,0.792 0.406,0.333 10 false A13 0.188,4.25 0.75,4.583 0.563,0.333 10 false CANL 0.177,2.521 0.74,2.854 0.563,0.333 10 false CANH 2.5,2.021 3.063,2.354 0.563,0.333 10 false CANH 2.5,0.406 3.063,0.74 0.563,0.333 10 false CANL
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))
*b Front view of wire harness connector
(to ECM)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A13-22 (CANH) - A24-39 (CANH) Cable disconnected from negative (-) battery terminal Below 1 Ω
A13-10 (CANL) - A24-40 (CANL) Cable disconnected from negative (-) battery terminal Below 1 Ω



Result:
Result Proceed to
OK (for 1NR-VE) A
OK (for 2NR-VE) B
NG C



A

B

C

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY))