Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2015.08
RM19Y0E _57 Power Source / Network _003004 NETWORKING _0015181 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Open in CAN Main Bus Line  


DESCRIPTION

There may be an open circuit in one of the V bus main lines and/or a DLC3 branch line when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 70 Ω or higher.

Symptom Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 is 70 Ω or higher.
·

DLC3 branch line or connector

·

CAN main bus line or connector

·

ECM

·

Combination meter assembly

·

Main body ECU (fuse block assembly)

·

No. 1 CAN junction connector



This malfunction is not related to the lines of a CAN main bus branch or to ECUs or sensors connected to a CAN main bus branch.

WIRING DIAGRAM

C329973E02
4.813,1.042 5.344,1.396 0.531,0.354 10 false ECM 4.813,0.854 5.333,1.104 0.521,0.25 10 false A24 0.729,5.729 1.26,6.083 0.531,0.354 10 false DLC3 0.979,7.573 3.094,7.896 2.115,0.323 10 false : CAN Main Bus Line (CANH) 0.99,7.938 3.073,8.281 2.083,0.344 10 false : CAN Main Bus Line (CANL) 4.25,7.938 6.365,8.26 2.115,0.323 10 false : CAN Branch Line (CANL) 4.25,7.583 6.365,7.906 2.115,0.323 10 false : CAN Branch Line (CANH) 4.021,1.896 4.406,2.156 0.385,0.26 10 false 3C 3.271,1.896 3.656,2.156 0.385,0.26 10 false 3C 3.26,3.604 3.646,3.865 0.385,0.26 10 false 3G 4.031,3.594 4.417,3.854 0.385,0.26 10 false 3G 4.51,3.615 6.146,4.083 1.635,0.469 10 false Fuse Block Assembly 4.458,4.719 6.427,5.156 1.969,0.438 10 false No. 1 CAN Junction Connector 4.771,6.552 6.677,6.979 1.906,0.427 10 false Combination Meter Assembly 4.771,6.375 5.302,6.625 0.531,0.25 10 false E34 3.5,0.594 4.052,0.927 0.552,0.333 10 false 120 Ω 3.531,6.792 4.083,7.125 0.552,0.333 10 false 120 Ω 1.365,4.875 1.917,5.208 0.552,0.333 10 false CANH 1.26,5.219 1.813,5.552 0.552,0.333 10 false CANL 0.729,5.552 1.25,5.802 0.521,0.25 10 false E12 1,7.167 2.198,7.51 1.198,0.344 10 false : Suspected Area 0.104,0.115 0.854,0.49 0.75,0.375 12 false V Bus: 1.885,4.792 2.198,5.073 0.313,0.281 10 false 6 1.688,5.333 2,5.615 0.313,0.281 10 false 14 4.167,6.125 4.479,6.406 0.313,0.281 10 false 9 3.188,6.125 3.5,6.406 0.313,0.281 10 false 8 4.177,1.021 4.729,1.354 0.552,0.333 10 false HCAN 2.917,6.375 3.469,6.708 0.552,0.333 10 false CANL 4.198,5.906 4.542,6.156 0.344,0.25 10 false W 3.146,5.906 3.49,6.156 0.344,0.25 10 false P 4.167,5.688 4.479,5.969 0.313,0.281 10 false 9 3.146,5.688 3.458,5.969 0.313,0.281 10 false 20 3.094,1.49 3.438,1.74 0.344,0.25 10 false W 4.198,1.479 4.542,1.729 0.344,0.25 10 false GR 2.938,1.031 3.49,1.365 0.552,0.333 10 false LCAN 4.167,1.26 4.479,1.542 0.313,0.281 10 false 25 3.146,1.26 3.458,1.542 0.313,0.281 10 false 26 2.292,5.417 2.802,5.729 0.51,0.313 10 false L-W 2.271,4.708 2.677,4.958 0.406,0.25 10 false G-W 3.125,3.823 3.438,4.104 0.313,0.281 10 false 16 4.167,3.833 4.479,4.115 0.313,0.281 10 false 17 4.208,4.073 4.552,4.323 0.344,0.25 10 false BE 3.083,4.042 3.427,4.292 0.344,0.25 10 false W 4.167,1.688 4.479,1.969 0.313,0.281 10 false 21 3.135,1.688 3.448,1.969 0.313,0.281 10 false 30 4.156,4.344 4.469,4.625 0.313,0.281 10 false 8 3.146,4.344 3.458,4.625 0.313,0.281 10 false 19 2.938,4.771 3.25,5.052 0.313,0.281 10 false 4 2.865,5.333 3.177,5.615 0.313,0.281 10 false 15 4.177,6.375 4.729,6.708 0.552,0.333 10 false CANH 4.458,4.542 4.844,4.802 0.385,0.26 10 false E87 4.688,2.448 5.792,2.917 1.104,0.469 10 false Main Body ECU 4.177,3.177 4.729,3.51 0.552,0.333 10 false CANH 4.167,2.333 4.719,2.667 0.552,0.333 10 false CANH 2.927,2.333 3.479,2.667 0.552,0.333 10 false CANL 2.927,3.177 3.479,3.51 0.552,0.333 10 false CANL

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON, wait at least 60 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (DLC3 BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
E231257C41
1.458,0.26 1.865,0.51 0.406,0.25 2.5,0.417 2.333,0.417 2.333,0.417 2,0.917 true 1.583,1.833 1.75,1.833 1.75,1.833 1.917,1.469 true 0.104,0.094 0.5,0.417 0.396,0.323 10 false *1 2.583,0.344 3.167,0.667 0.583,0.323 10 false CANH 1.156,1.76 1.573,2.01 0.417,0.25 10 false CANL 1.542,0.302 2.042,0.635 0.5,0.333 10 false E12
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E12-6 (CANH) - E12-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


NOTICE:

When the measured value is 133 Ω or higher and a CAN communication system DTC is output, there may be a fault besides disconnection of the DLC3 branch line. For that reason, troubleshooting should be performed again from How to Proceed with Troubleshooting after repairing the trouble area.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



Result:
Proceed to
OK
NG



OK

2.CHECK FOR OPEN IN CAN BUS LINES (ECM - MAIN BODY ECU (FUSE BLOCK ASSEMBLY))

NG

REPAIR OR REPLACE CAN BRANCH LINE CONNECTED TO DLC3

2.CHECK FOR OPEN IN CAN BUS LINES (ECM - MAIN BODY ECU (FUSE BLOCK ASSEMBLY))
a.
A348485C07
1.5,0.25 1.917,0.5 0.417,0.25 0.969,0.958 0.969,0.125 0.969,0.125 1.135,0.125 true 0.844,0.948 0.844,0.365 0.844,0.365 0.677,0.365 true 0.094,0.104 0.385,0.385 0.292,0.281 10 false *a 1.583,0.292 2.01,0.563 0.427,0.271 10 false A24 0.281,0.292 0.781,0.542 0.5,0.25 10 false LCAN 1.198,0.052 1.698,0.302 0.5,0.25 10 false HCAN
*a Front view of wire harness connector
(to ECM)


Disconnect the A24 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-25 (HCAN) - A24-26 (LCAN) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result Proceed to
OK (for 1NR-VE) A
OK (for 2NR-VE) B
NG C



A

B

C

3.CHECK FOR OPEN IN CAN BUS LINES (COMBINATION METER ASSEMBLY - NO. 1 CAN JUNCTION CONNECTOR)
3.CHECK FOR OPEN IN CAN BUS LINES (COMBINATION METER ASSEMBLY - NO. 1 CAN JUNCTION CONNECTOR)
a.

Reconnect the A24 ECM connector.


b.
E208723C04
1.49,0.271 1.906,0.521 0.417,0.25 1.375,1.125 1.083,0.417 1.083,0.417 0.917,0.417 true 1.552,1.104 2.25,0.417 2.25,0.417 2.417,0.417 true 0.115,0.104 0.448,0.396 0.333,0.292 10 false *a 1.573,0.313 1.906,0.604 0.333,0.292 10 false E34 2.5,0.333 3,0.625 0.5,0.292 10 false CANH 0.5,0.344 1,0.635 0.5,0.292 10 false CANL
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the E34 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E34-9 (CANH) - E34-8 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

4.CHECK FOR OPEN IN CAN BUS LINES (MAIN BODY ECU (FUSE BLOCK ASSEMBLY))
4.CHECK FOR OPEN IN CAN BUS LINES (MAIN BODY ECU (FUSE BLOCK ASSEMBLY))
a.

Reconnect the E34 combination meter assembly connector.


b.
C329970C03
1.521,2.667 1.938,2.917 0.417,0.25 1.469,0.448 1.885,0.698 0.417,0.25 2.052,1.271 2.406,0.531 2.406,0.531 2.573,0.531 true 2.042,1.51 2.323,2.052 2.323,2.052 2.49,2.052 true 1.865,3.823 2.094,4.396 2.094,4.396 2.26,4.396 true 1.719,3.823 1.469,4.375 1.469,4.375 1.302,4.375 true 0.125,0.135 0.458,0.406 0.333,0.271 10 false *a 1.583,0.49 2,0.771 0.417,0.281 10 false 3C 1.635,2.708 2.052,2.99 0.417,0.281 10 false 3G 2.313,4.313 3.042,4.594 0.729,0.281 10 false CANH*c 2.635,0.458 3.271,0.802 0.635,0.344 10 false CANH*b 2.542,1.979 3.146,2.302 0.604,0.323 10 false CANL*b 0.76,4.281 1.417,4.594 0.656,0.313 10 false CANL*c
*a Front view of wire harness connector
(to Main Body ECU (Fuse Block Assembly))
*b to ECM
*c to No. 1 CAN Junction Connector


Disconnect the 3C and 3G main body ECU (fuse block assembly) connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
3C-21 (CANH) - 3C-30 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω ECM
3G-17 (CANH) - 3G-16 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 1 CAN junction connector



Result:
Result Proceed to
OK (for RHD) A
OK (for LHD) B
NG (ECM main line) C
NG (No. 1 CAN junction connector main line) D



A

REPLACE MAIN BODY ECU (FUSE BLOCK ASSEMBLY)

B

REPLACE MAIN BODY ECU (FUSE BLOCK ASSEMBLY)

C

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (MAIN BODY ECU (FUSE BLOCK ASSEMBLY) - ECM)

D

5.CHECK FOR OPEN IN CAN BUS LINES (NO. 1 CAN JUNCTION CONNECTOR)
5.CHECK FOR OPEN IN CAN BUS LINES (NO. 1 CAN JUNCTION CONNECTOR)
a.

Reconnect the 3C and 3G main body ECU (fuse block assembly) connectors.


b.
C248060C21
0.083,1.417 0.5,1.667 0.417,0.25 2.052,1.906 1.781,2.667 1.781,2.667 1.615,2.667 true 2.26,1.906 2.438,2.667 2.438,2.667 2.604,2.667 true 2.042,1.521 1.771,0.5 1.771,0.5 1.604,0.5 true 2.25,1.51 2.5,0.5 2.5,0.5 2.667,0.5 true 0.115,0.104 0.417,0.375 0.302,0.271 10 false *a 2.719,0.427 3.146,0.792 0.427,0.365 10 false *c 2.667,2.604 3.073,2.938 0.406,0.333 10 false *c 1.396,0.406 1.792,0.729 0.396,0.323 10 false *b 1.417,2.583 1.771,2.875 0.354,0.292 10 false *b 0.167,1.458 0.656,1.792 0.49,0.333 10 false E87
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to Main Body ECU (Fuse Block Assembly)
*c to Combination Meter Assembly


Disconnect the E87 No. 1 CAN junction connector connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
E87-8 (CANH) - E87-19 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Main body ECU (fuse block assembly)
E87-9 (CANH) - E87-20 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Combination meter assembly



Result:
Result Proceed to
OK A
NG (Main body ECU (fuse block assembly) main line) B
NG (Combination meter assembly main line) C



A

REPLACE NO. 1 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - MAIN BODY ECU (FUSE BLOCK ASSEMBLY))

C

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)