1.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
3.DRAIN ENGINE COOLANT
for 1NR-VE (Click hereEngine / Hybrid System>1NR-VE COOLING>COOLANT>REPLACEMENT)
for 2NR-VE (Click hereEngine / Hybrid System>2NR-VE COOLING>COOLANT>REPLACEMENT)
87245X
4.REMOVE NO. 1 HEATER WATER HOSE (w/ Heater)
Slide the clip and disconnect the No. 1 heater water hose from the air conditioning unit assembly.
Use the same procedure for the RHD and LHD vehicles.
87246X
5.REMOVE NO. 2 HEATER WATER HOSE (w/ Heater)
Slide the clip and disconnect the No. 2 heater water hose from the air conditioning unit assembly.
Use the same procedure for the RHD and LHD vehicles.
88899P
6.REMOVE COVER PLATE (w/o Air Conditioning System)
Remove the bolt and the cover plate.
88712D
7.DISCONNECT SUCTION HOSE (for RHD)
Remove the bolt.
Turn the hook connector clockwise and disconnect the suction hose.
Remove the O-ring from the suction hose.
Seal the openings of the disconnected parts using vinyl tape to prevent the entry of moisture and foreign matter.
88712D
8.DISCONNECT SUCTION HOSE (for LHD)
Remove the bolt.
Turn the hook connector counterclockwise and disconnect the suction hose.
Remove the O-ring from the suction hose.
Seal the openings of the disconnected parts using vinyl tape to prevent the entry of moisture and foreign matter.
88716A
9.DISCONNECT COOLER REFRIGERANT LIQUID PIPE A (for RHD)
Disconnect the cooler refrigerant liquid pipe A.
Remove the O-ring from the cooler refrigerant liquid pipe A.
Seal the opening of the disconnected parts using vinyl tape to prevent the entry of moisture and foreign matter.
88716A
10.DISCONNECT COOLER REFRIGERANT LIQUID PIPE A (for LHD)
Disconnect the cooler refrigerant liquid pipe A.
Remove the O-ring from the cooler refrigerant liquid pipe A.
Seal the opening of the disconnected parts using vinyl tape to prevent the entry of moisture and foreign matter.
55301
11.REMOVE INSTRUMENT PANEL SUB-ASSEMBLY
55312
12.REMOVE LOWER INSTRUMENT PANEL
45250
13.REMOVE STEERING COLUMN ASSEMBLY
55317
14.REMOVE INSTRUMENT PANEL PATCH
Remove the 2 bolts and the instrument panel patch.
55453D
15.REMOVE NO. 1 INSTRUMENT PANEL SAFETY PAD
Disengage the 2 clamps to remove the No. 1 instrument panel safety pad.
Use the same procedure for the RHD and LHD vehicles.
55454B
16.REMOVE NO. 2 INSTRUMENT PANEL SAFETY PAD
Use the same procedure as for the No. 1 instrument panel safety pad.
82673B
17.REMOVE JUNCTION BLOCK BRACKET (for LHD)
Remove the 2 bolts and junction block bracket.
82600
18.REMOVE FUSE BLOCK ASSEMBLY
Disconnect each connector.
Remove the bolt and slide the fuse block assembly as shown indicated by the arrow in the illustration to remove it.
82141
19.SEPARATE INSTRUMENT PANEL WIRE (for RHD)
Disconnect the 2 connectors and disengage the 2 clamps.
Disconnect the connector and disengage the 4 clamps.
Disconnect the connector and disengage the clamp.
Remove the bolt and disconnect the ground wire from the instrument panel reinforcement.
Disengage the 3 clamps.
Remove the bolt and disconnect the ground wire from the instrument panel reinforcement.
Disengage the 2 clamps and separate the instrument panel wire from the instrument panel reinforcement.
Disengage the 2 claws and disconnect the DLC3 connector.
82141
20.SEPARATE INSTRUMENT PANEL WIRE (for LHD)
Disconnect the 2 connectors and disengage the clamp.
Remove the bolt and disconnect the ground wire from the instrument panel reinforcement.
Disengage the 3 clamps.
Disconnect the connector and disengage the clamp.
Disengage the 3 clamps.
Remove the bolt and disconnect the ground wire from the instrument panel reinforcement.
Disengage the 2 clamps.
Remove the 2 bolts and disconnect the ground wire from the instrument panel reinforcement.
Disengage the 4 camps and separate the instrument panel wire from the instrument panel reinforcement.
87220
21.REMOVE AIR DUCT ASSEMBLY
Remove the 2 bolts and the air duct assembly.
Use the same procedure for the RHD and LHD vehicles.
88539J
22.REMOVE DRAIN COOLER HOSE
Use the same procedure for the RHD and LHD vehicles.
Separate the drain cooler hose from the air conditioning unit assembly.
Remove the grommet.
55352A
23.REMOVE NO. 2 INSTRUMENT PANEL TO FLOOR BRACE
Remove the bolt and No. 2 instrument panel to floor brace.
Use the same procedure for the RHD and LHD vehicles.
55331
24.REMOVE INSTRUMENT PANEL REINFORCEMENT (for RHD)
Remove the bolt from the engine compartment.
Remove the 2 bolts from the front pillar.
Use the same procedure for the LH side and RH side.
Remove the 5 bolts and the instrument panel reinforcement with the air conditioning unit assembly.
55331
25.REMOVE INSTRUMENT PANEL REINFORCEMENT (for LHD)
Remove the bolt from the engine compartment.
Remove the 2 bolts from the front pillar.
Use the same procedure for the LH side and RH side.
Remove the 4 bolts and the instrument panel reinforcement with the air conditioning unit assembly.
87010
26.REMOVE AIR CONDITIONING UNIT ASSEMBLY (for RHD)
w/o Heater:
Remove the 2 bolts, nut and air conditioning unit assembly from the instrument panel reinforcement.
w/ Heater:
Remove the 2 bolts, nut and air conditioning unit assembly from the instrument panel reinforcement.
87010
27.REMOVE AIR CONDITIONING UNIT ASSEMBLY (for LHD)
Remove the 2 bolts, nut and air conditioning unit assembly from the instrument panel reinforcement.