The intake air flow meter assembly is a sensor that measures the amount of air flowing through the throttle valve. The ECM uses this information to determine the fuel injection duration and to provide an appropriate air fuel ratio.
Inside the intake air flow meter assembly, there is a heated platinum wire which is exposed to the flow of intake air. By applying a specific electrical current to the wire, the ECM heats it to a specific temperature. The flow of incoming air cools both the wire and an internal thermistor, affecting their resistance. To maintain a constant current value, the ECM varies the voltage applied to the wire and internal thermistor. The voltage level is proportional to the airflow through the sensor, and the ECM uses it to calculate the intake air volume.
The circuit is constructed so that the platinum hot wire and the temperature sensor create a bridge circuit, and the power transistor is controlled so that the potentials of A and B remain equal to maintain the predetermined temperature.
When any of these DTCs is stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is calculated by the ECM, according to the engine speed and throttle valve position. Fail-safe mode continues until a pass condition is detected.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0102 | Air Flow Sensor System Open/Low | The intake air flow meter assembly voltage is less than 0.2 V for 3 seconds (1 trip detection logic). | ·
Open or short in intake air flow meter assembly circuit ·
Intake air flow meter assembly ·
ECM |
Comes on | DTC stored |
| P0103 | Air Flow Sensor System Open/High | The intake air flow meter assembly voltage is higher than 4.9 V for 3 seconds (1 trip detection logic). | ·
Open or short in intake air flow meter assembly circuit ·
Intake air flow meter assembly ·
ECM |
Comes on | DTC stored |
When any of these DTCs are output, check the air flow rate using the GTS. Enter the following menus: Powertrain / EFI / Data List / Air flow rate.
| Air Flow Rate (g/s) | Malfunction |
|---|---|
| Approximately 0.0 | ·
Open in intake air flow meter assembly power source circuit ·
Open or short in VG circuit |
| 271.0 or more | ·
Open in E2G circuit |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the GTS on.
Wait for 5 seconds or more.
Enter the following menus: Powertrain / EFI / Trouble Codes.
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, the system is normal.
Inspect the fuses for circuits related to this system before performing the following procedure.
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / EFI / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P0102 is output | A |
| DTC P0103 is output | B |
A
B
| *a | Front view of wire harness connector
(to Intake Air Flow Meter Assembly) |
Disconnect the intake air flow meter assembly connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C41-3 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the intake air flow meter assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C41-5 (VG) - C50-76 (VG) | Always | Below 1 Ω |
| C41-4 (E2G) - C50-98 (E2G) | Always | Below 1 Ω |
| C41-5 (VG) or C50-76 (VG) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the intake air flow meter assembly, referring to the On-vehicle Inspection for Mass Air Flow Meter.
Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>MASS AIR FLOW METER>ON-VEHICLE INSPECTION
Inspect the intake air flow meter assembly, referring to the Inspection for Mass Air Flow Meter.
Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>MASS AIR FLOW METER>INSPECTION
Inspect the function of the intake air flow meter assembly.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / EFI / Data List / Air flow rate.
Start the engine.
Check that the Air flow rate value changes when the engine is raced.
The reading changes.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the intake air flow meter assembly connector.
Disconnect the No. 1 integration relay connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C41-3 (+B) - 1J-3 | Always | Below 1 Ω |
| C41-3 (+B) or 1J-3 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the No. 1 integration relay.
Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>INTEGRATION RELAY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the intake air flow meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C41-4 (E2G) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the intake air flow meter assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C41-4 (E2G) - C50-98 (E2G) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG