Home › Engine / Hybrid System › 2NR-VE ENGINE CONTROL › SFI SYSTEM(w/o Air Fuel Ratio Sensor) › 2015.08–2016.09
RM19Y0E _51 Engine / Hybrid System _042272 2NR-VE ENGINE CONTROL _0196163 SFI SYSTEM(w/o Air Fuel Ratio Sensor) C

2NR-VE ENGINE CONTROL  SFI SYSTEM(w/o Air Fuel Ratio Sensor)  P0300  Misfire (Random)  P0301  Misfire (Cylinder #1)  P0302  Misfire (Cylinder #2)  P0303  Misfire (Cylinder #3)  P0304  Misfire (Cylinder #4)  


DESCRIPTION

When the engine misfires, high concentrations of hydrocarbons (HC) enter the exhaust gas. Extremely high hydrocarbon concentration levels can cause an increase in exhaust emission levels. Extremely high concentrations of hydrocarbons can also cause increases in the three-way catalytic converter temperature, which may cause damage to the three-way catalytic converter. To prevent this increase in emissions and to limit the possibility of thermal damage, the ECM monitors the misfire count. When the temperature of the three-way catalytic converter reaches the point of thermal degradation, the ECM blinks the MIL. To monitor misfires, the ECM uses both the camshaft position sensor and the crankshaft position sensor. The camshaft position sensor is used to identify any misfiring cylinders and the crankshaft position sensor is used to measure variations in the crankshaft rotation speed. Misfires are counted when the crankshaft rotation speed variations exceed predetermined thresholds. If the misfire count exceeds the threshold levels, and could cause emission control system performance deterioration, the ECM illuminates the MIL and sets a DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0300 Misfire (Random) Simultaneous misfiring of several cylinders detected
(2 trip detection logic)
·

Open or short in engine wire harness

·

Connector connection

·

PCV valve and ventilation hose

·

Ventilation hose connections

·

Ignition system

·

Fuel injector assembly

·

Fuel pressure

·

Intake air flow meter assembly

·

Engine Coolant Temperature (ECT) sensor

·

Compression pressure

·

Valve clearance

·

Valve timing

·

ECM


Comes on/Blinks*
*: The MIL flashes when a catalystdamaging misfire is detected.
DTC stored
P0301 Misfire (Cylinder #1) Misfiring of specific cylinder detected
(2 trip detection logic)
·

Open or short in engine wire harness

·

Connector connection

·

PCV valve and ventilation hose

·

Ventilation hose connections

·

Ignition system

·

Fuel injector assembly

·

Fuel pressure

·

Intake air flow meter assembly

·

Engine Coolant Temperature (ECT) sensor

·

Compression pressure

·

Valve clearance

·

Valve timing

·

ECM


Comes on/Blinks*
*: The MIL flashes when a catalystdamaging misfire is detected.
DTC stored
P0302 Misfire (Cylinder #2) Misfiring of specific cylinder detected
(2 trip detection logic)
·

Open or short in engine wire harness

·

Connector connection

·

PCV valve and ventilation hose

·

Ventilation hose connections

·

Ignition system

·

Fuel injector assembly

·

Fuel pressure

·

Intake air flow meter assembly

·

Engine Coolant Temperature (ECT) sensor

·

Compression pressure

·

Valve clearance

·

Valve timing

·

ECM


Comes on/Blinks*
*: The MIL flashes when a catalystdamaging misfire is detected.
DTC stored
P0303 Misfire (Cylinder #3) Misfiring of specific cylinder detected
(2 trip detection logic)
·

Open or short in engine wire harness

·

Connector connection

·

PCV valve and ventilation hose

·

Ventilation hose connections

·

Ignition system

·

Fuel injector assembly

·

Fuel pressure

·

Intake air flow meter assembly

·

Engine Coolant Temperature (ECT) sensor

·

Compression pressure

·

Valve clearance

·

Valve timing

·

ECM


Comes on/Blinks*
*: The MIL flashes when a catalystdamaging misfire is detected.
DTC stored
P0304 Misfire (Cylinder #4) Misfiring of specific cylinder detected
(2 trip detection logic)
·

Open or short in engine wire harness

·

Connector connection

·

PCV valve and ventilation hose

·

Ventilation hose connections

·

Ignition system

·

Fuel injector assembly

·

Fuel pressure

·

Intake air flow meter assembly

·

Engine Coolant Temperature (ECT) sensor

·

Compression pressure

·

Valve clearance

·

Valve timing

·

ECM


Comes on/Blinks*
*: The MIL flashes when a catalystdamaging misfire is detected.
DTC stored

When DTCs for misfiring cylinders are randomly set, but DTC P0300 is not set, it indicates that misfires have been detected in different cylinders at different times. DTC P0300 is only set when several misfiring cylinders are detected at the same time.

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Record the DTC(s) and freeze frame data.

4.

Drive the vehicle several times with the conditions when malfunctions are detected.

HINT:

In order to store misfire DTCs, it is necessary to drive the vehicle for the period of time shown in the table below.

Engine RPM Duration
1000 4.5 minutes or more
2000 2.5 minutes or more
3000 1.5 minute or more


5.

Check whether misfires have occurred by checking DTCs and freeze frame data.

HINT:

Do not turn the ignition switch off until the stored DTC(s) and freeze frame data have been recorded. The stored DTC(s), freeze frame data and other data will be erased.


6.

Record the DTC(s), freeze frame data.

7.

Turn the ignition switch off and wait for at least 30 seconds.


WIRING DIAGRAM

Wiring diagram of the ignition system.

A357522E02
0.646,6.573 1.323,6.917 0.677,0.344 10 false Battery 0.5,5.792 1.177,6.031 0.677,0.24 10 false FL MAIN 0.719,0.51 1.188,0.813 0.469,0.302 10 false AM1 2.656,2.375 3.073,2.604 0.417,0.229 10 false IG2 2.094,2.813 3.802,3.219 1.708,0.406 10 false No. 1 Integration Relay 2.865,3.813 4.75,4.229 1.885,0.417 10 false No. 1 Ignition Coil Assembly 2.875,4.927 4.76,5.344 1.885,0.417 10 false No. 2 Ignition Coil Assembly 2.885,6 4.771,6.417 1.885,0.417 10 false No. 3 Ignition Coil Assembly 2.896,7.115 4.781,7.531 1.885,0.417 10 false No. 4 Ignition Coil Assembly 2.865,3.646 3.271,3.885 0.406,0.24 10 false C28 2.875,4.76 3.281,5.01 0.406,0.25 10 false C29 2.885,5.833 3.292,6.073 0.406,0.24 10 false C30 2.896,6.948 3.302,7.188 0.406,0.24 10 false C31 5.969,7.792 6.375,8.031 0.406,0.24 10 false C50 3.875,1.406 4.125,1.646 0.25,0.24 10 false 5 2.063,0.24 2.313,0.479 0.25,0.24 10 false 1 1.542,1.615 1.948,1.854 0.406,0.24 10 false 1E 1.583,1.406 1.833,1.646 0.25,0.24 10 false 5 4.448,1.75 4.917,2.052 0.469,0.302 10 false E/G 0.604,1.76 1.25,2.083 0.646,0.323 10 false IG MAIN 1.531,2.094 1.938,2.333 0.406,0.24 10 false 1D 1.573,1.885 1.823,2.125 0.25,0.24 10 false 1 3.833,1.615 4.24,1.854 0.406,0.24 10 false 1D 3.833,2.104 4.24,2.344 0.406,0.24 10 false 1F 3.823,1.896 4.073,2.135 0.25,0.24 10 false 18 1.719,0.771 4.052,1.146 2.333,0.375 10 false Ignition or Starter Switch Assembly 1.719,0.604 2.125,0.844 0.406,0.24 10 false E28 3.333,0.229 3.583,0.469 0.25,0.24 10 false 2 2.24,0.25 2.708,0.552 0.469,0.302 10 false AM 3.021,0.25 3.49,0.552 0.469,0.302 10 false IG1 5.427,3.458 5.677,3.698 0.25,0.24 10 false 40 5.427,4.573 5.677,4.813 0.25,0.24 10 false 41 5.427,5.635 5.677,5.875 0.25,0.24 10 false 42 5.427,6.74 5.677,6.979 0.25,0.24 10 false 43 6.313,7.792 6.802,8.094 0.49,0.302 10 false ECM 3.885,3.365 4.135,3.604 0.25,0.24 10 false + 3.5,3.448 3.75,3.688 0.25,0.24 10 false - 3.781,3.552 4.24,3.813 0.458,0.26 10 false IGT 3.885,4.479 4.135,4.719 0.25,0.24 10 false + 3.896,5.542 4.146,5.781 0.25,0.24 10 false + 3.896,6.635 4.146,6.875 0.25,0.24 10 false + 3.5,4.563 3.75,4.802 0.25,0.24 10 false - 3.5,5.635 3.75,5.875 0.25,0.24 10 false - 3.5,6.729 3.75,6.969 0.25,0.24 10 false - 3.781,4.667 4.24,4.927 0.458,0.26 10 false IGT 3.792,5.74 4.25,6 0.458,0.26 10 false IGT 3.792,6.844 4.25,7.104 0.458,0.26 10 false IGT 4.083,3.24 4.333,3.479 0.25,0.24 10 false 1 4.094,3.458 4.344,3.698 0.25,0.24 10 false 3 3.292,3.333 3.542,3.573 0.25,0.24 10 false 4 4.083,4.365 4.333,4.604 0.25,0.24 10 false 1 4.083,5.417 4.333,5.656 0.25,0.24 10 false 1 4.073,6.542 4.323,6.781 0.25,0.24 10 false 1 4.094,4.583 4.344,4.823 0.25,0.24 10 false 3 4.094,5.646 4.344,5.885 0.25,0.24 10 false 3 4.083,6.76 4.333,7 0.25,0.24 10 false 3 3.302,4.458 3.552,4.698 0.25,0.24 10 false 4 3.302,5.531 3.552,5.771 0.25,0.24 10 false 4 3.302,6.625 3.552,6.865 0.25,0.24 10 false 4 5.677,3.448 6.083,3.688 0.406,0.24 10 false IG1 5.677,4.563 6.083,4.802 0.406,0.24 10 false IG2 5.656,5.635 6.063,5.875 0.406,0.24 10 false IG3 5.677,6.74 6.083,6.979 0.406,0.24 10 false IG4

Wiring diagram of the injector circuit.

A357514E02
2.625,2.26 2.938,2.458 0.313,0.198 10 false 1J 5.354,0.219 5.667,0.417 0.313,0.198 10 false 28 2.615,0.417 2.927,0.615 0.313,0.198 10 false 1F 0.49,2.646 0.802,2.844 0.313,0.198 10 false 1F 0.656,3.625 1.115,3.958 0.458,0.333 10 false EFI 6.125,7.042 6.604,7.344 0.479,0.302 10 false ECM 3.417,2.594 5.365,3.01 1.948,0.417 10 false No. 1 Fuel Injector Assembly 3.417,3.719 5.333,4.094 1.917,0.375 10 false No. 2 Fuel Injector Assembly 3.417,4.792 5.375,5.135 1.958,0.344 10 false No. 3 Fuel Injector Assembly 3.417,5.906 5.385,6.292 1.969,0.385 10 false No. 4 Fuel Injector Assembly 5.677,2.156 6.125,2.458 0.448,0.302 10 false #10 5.677,6.427 6.063,6.708 0.385,0.281 10 false E01 5.677,3.26 6.063,3.563 0.385,0.302 10 false #20 5.677,4.333 6.042,4.615 0.365,0.281 10 false #30 5.677,5.448 6.052,5.74 0.375,0.292 10 false #40 5.302,6.531 5.677,6.771 0.375,0.24 10 false C50 5.302,5.552 5.708,5.865 0.406,0.313 10 false C50 5.302,4.448 5.719,4.781 0.417,0.333 10 false C50 5.302,3.375 5.688,3.708 0.385,0.333 10 false C50 5.313,2.26 5.708,2.583 0.396,0.323 10 false C50 5.302,0.417 5.719,0.677 0.417,0.26 10 false A24 5.313,1.563 5.74,1.896 0.427,0.333 10 false A24 5.396,1.365 5.708,1.563 0.313,0.198 10 false 1 5.354,2.052 5.667,2.25 0.313,0.198 10 false 18 5.344,3.167 5.656,3.365 0.313,0.198 10 false 19 5.354,4.24 5.667,4.438 0.313,0.198 10 false 20 5.354,5.344 5.667,5.542 0.313,0.198 10 false 21 5.396,6.354 5.708,6.552 0.313,0.198 10 false 4 0.99,2.26 1.781,2.573 0.792,0.313 10 false EFI-MAIN 2.615,1.573 2.927,1.771 0.313,0.198 10 false 1F 5.677,0.417 6.208,0.75 0.531,0.333 10 false MRO 5.677,1.563 6.104,1.854 0.427,0.292 10 false +B1 0.594,2.854 0.906,3.052 0.313,0.198 10 false 17 2.656,2.063 2.969,2.26 0.313,0.198 10 false 3 2.604,1.375 2.917,1.573 0.313,0.198 10 false 10 2.646,0.208 2.958,0.406 0.313,0.198 10 false 5 0.813,6.021 1.594,6.406 0.781,0.385 10 false Battery 0.979,2.667 2.854,3.146 1.875,0.479 10 false No. 1 Integration Relay 0.667,4.792 1.479,5.052 0.813,0.26 10 false FL MAIN 3.417,2.427 3.833,2.698 0.417,0.271 10 false C32 3.406,3.542 3.833,3.823 0.427,0.281 10 false C33 3.406,4.615 3.833,4.927 0.427,0.313 10 false C34 3.406,5.74 3.833,6.031 0.427,0.292 10 false C35 4.667,3.24 4.979,3.438 0.313,0.198 10 false 2 4.667,2.125 4.979,2.323 0.313,0.198 10 false 2 4.656,4.313 4.969,4.51 0.313,0.198 10 false 2 4.656,5.427 4.969,5.625 0.313,0.198 10 false 2 3.875,5.438 4.188,5.635 0.313,0.198 10 false 1 3.865,4.313 4.177,4.51 0.313,0.198 10 false 1 3.865,3.25 4.177,3.448 0.313,0.198 10 false 1 3.865,2.135 4.177,2.333 0.313,0.198 10 false 1

CAUTION / NOTICE / HINT

HINT:
·

If any DTCs other than misfire DTCs are output, troubleshoot those DTCs first.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

If the misfire does not recur when the vehicle is brought to the workshop, reproduce the conditions stored in the freeze frame data.

·

If the misfire still cannot be reproduced even though the conditions stored in the freeze frame data have been duplicated, one of the following factors is considered to be a possible cause of the problem:

1.

The fuel level is low.

2.

Improper fuel is used.

3.

The spark plugs are dirty.

4.

The problem is complex due to multiple factors.


·

After finishing repairs, check that no misfire occur in each cylinder (Cylinder #1, #2, #3 and #4).

·

Be sure to confirm that no misfiring cylinder DTCs are set again by conducting the confirmation driving pattern, after the repairs.

·

When either Short FT #1 or Long FT #1 in the freeze frame data is outside the range of +/-20%, the air-fuel ratio may be rich (-20% or less) or lean (+20% or more).

·

When the Engine coolant temperature in the freeze frame data is less than 75°C (167°F), the misfires occurred only while warming up the engine.

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO MISFIRE DTCS)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / EFI / Trouble Codes.


e.

Read DTCs.

HINT:

If any DTCs other than P0300, P0301, P0302, P0303 and P0304 are output, troubleshoot those DTCs first.



Result:
Result Proceed to
P0300, P0301, P0302, P0303 and/or P0304 are output A
P0300, P0301, P0302, P0303 and/or P0304 and other DTCs are output B



A

2.CHECK VENTILATION HOSE CONNECTIONS

B

2.CHECK VENTILATION HOSE CONNECTIONS
a.

Check the ventilation hose connections.

Click hereEngine / Hybrid System>2NR-VE EMISSION CONTROL>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION

OK:

Ventilation hose is connected correctly and is not damaged.



Result:
Proceed to
OK
NG



OK

3.CHECK SPARK PLUG

NG

REPAIR OR REPLACE PCV HOSE

3.CHECK SPARK PLUG
a.
A126880C30
0.719,1.135 1.25,1.458 0.531,0.323 10 false *a
*a Electrode Gap


Remove the ignition coil and the spark plug of the misfiring cylinder.


b.

Measure the spark plug electrode gap.

Standard:

1.0 to 1.1 mm (0.0394 to 0.0433 in.)



c.

Check the electrode for carbon deposits.

Recommended spark plug:
Manufactures Products
DENSO SC16HR11


NOTICE:

If the electrode gap is larger than standard, replace the spark plug. Do not adjust the electrode gap.



d.

Reinstall the ignition coil and the spark plug.


Result:
Proceed to
OK
NG



OK

4.CHECK FOR SPARKS AND IGNITION

NG

4.CHECK FOR SPARKS AND IGNITION
a.

Check the ignition system.

HINT:

Refer to Ignition System / On-Vehicle Inspection.

Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>IGNITION SYSTEM>ON-VEHICLE INSPECTION


OK:

Spark occurs.



Result:
Proceed to
OK
NG



OK

5.CHECK CYLINDER COMPRESSION PRESSURE OF MISFIRING CYLINDER

NG

CHANGE NORMAL SPARK PLUG AND CHECK SPARK OF MISFIRING CYLINDER

5.CHECK CYLINDER COMPRESSION PRESSURE OF MISFIRING CYLINDER
a.

Measure the cylinder compression pressure of the misfiring cylinder.


Result:
Proceed to
OK
NG



OK

6.CHANGE NORMAL SPARK PLUG AND CHECK SPARK OF MISFIRING CYLINDER

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

6.CHANGE NORMAL SPARK PLUG AND CHECK SPARK OF MISFIRING CYLINDER
a.

Change the installed spark plug to a spark plug that functions normally.


b.

Perform a spark test.

CAUTION:

Always disconnect all injector connectors.


NOTICE:

Do not crank the engine for more than 2 seconds.


i.

Install the spark plug to the ignition coil and connect the ignition coil connector.


ii.

Disconnect the injector connector.


iii.

Ground the spark plug.


iv.

Check if sparks occur while the engine is being cranked.

OK:

Sparks jump across electrode gap.




Result:
Proceed to
OK
NG



OK

7.INSPECT ECM TERMINAL VOLTAGE OF MISFIRING CYLINDER (#10, #20, #30 AND/OR #40 VOLTAGE)

NG

REPLACE IGNITION COIL ASSEMBLY THEN CONFIRM THAT THERE IS NO MISFIRE

7.INSPECT ECM TERMINAL VOLTAGE OF MISFIRING CYLINDER (#10, #20, #30 AND/OR #40 VOLTAGE)
a.
A287504C33
0.396,1.583 0.833,1.833 0.438,0.25 0.396,2.01 0.833,2.25 0.438,0.24 0.396,2.406 0.833,2.667 0.438,0.26 0.396,2.823 0.833,3.083 0.438,0.26 0.094,0.104 0.552,0.531 0.458,0.427 10 false *a 0.479,1.635 0.792,1.833 0.313,0.198 10 false C32 0.49,2.052 0.802,2.25 0.313,0.198 10 false C33 0.49,2.458 0.802,2.656 0.313,0.198 10 false C34 0.49,2.865 0.802,3.063 0.313,0.198 10 false C35
*a Front view of wire harness connector
(to Fuel Injector Assembly)


Disconnect the fuel injector assembly connectors.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C32-1 - Body ground Ignition switch ON 11 to 14 V
C33-1 - Body ground Ignition switch ON 11 to 14 V
C34-1 - Body ground Ignition switch ON 11 to 14 V
C35-1 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

8.CHECK FUEL INJECTOR OF MISFIRING CYLINDER

NG

8.CHECK FUEL INJECTOR OF MISFIRING CYLINDER
a.

Check the fuel injector assembly (whether fuel volume is high or low, and whether injection pattern is poor).

Click hereEngine / Hybrid System>2NR-VE FUEL>FUEL INJECTOR>INSPECTION


Result:
Proceed to
OK
NG



OK

9.CHECK VALVE TIMING

NG

REPLACE FUEL INJECTOR ASSEMBLY

9.CHECK VALVE TIMING

Result:
Proceed to
OK
NG



OK

10.CHECK FUEL PRESSURE

NG

13.CHECK ENGINE MECHANICAL SYSTEM
10.CHECK FUEL PRESSURE

Result:
Proceed to
OK
NG



OK

11.READ VALUE USING GTS (ENGINE COOLANT TEMPERATURE)

NG

CHECK AND REPLACE FUEL PUMP, PRESSURE REGULATOR, FUEL PIPE LINE AND FILTER

11.READ VALUE USING GTS (ENGINE COOLANT TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / EFI / Data List / Engine coolant temperature.


e.

Read the Coolant Temp twice, when the engine is both cold and warmed up.

Standard:

With cold engine: Same as ambient air temperature.

With warm engine: 75°C to 100°C (167°F to 212°F).



Result:
Proceed to
OK
NG



OK

12.READ VALUE USING GTS (AIR FLOW RATE)

NG

12.READ VALUE USING GTS (AIR FLOW RATE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / EFI / Data List / Engine coolant temperature and Air flow rate.


e.

Allow the engine to idle until the Coolant Temp reaches 80°C (176°F) or more.


f.

Read Air flow rate with the engine speed at 3000 rpm.

Standard:
GTS Display Condition Specified Condition
Air flow rate Shift lever position: Neutral
A/C: Off
Engine Speed: 3000 rpm
Between 3.0 and 8.0 g/s



Result:
Proceed to
OK
NG



OK

13.CHECK ENGINE MECHANICAL SYSTEM

NG

REPLACE INTAKE AIR FLOW METER ASSEMBLY

13.CHECK ENGINE MECHANICAL SYSTEM
a.

Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.


Result:
Proceed to
OK
NG



OK

14.CHECK WHETHER DTC OUTPUT RECURS (MISFIRE DTCS)

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

14.CHECK WHETHER DTC OUTPUT RECURS (MISFIRE DTCS)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.


e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Start the engine and warm it up.


i.

Drive the vehicle in accordance with the driving pattern.


j.

Enter the following menus: Powertrain / EFI / Trouble Codes.


k.

Read the pending DTCs.


Result:
Result Proceed to
DTC is not output A
DTC P0300, P0301, P0302, P0303 and/or P0304 are output B



A

B