The camshaft position sensor for the exhaust camshaft (EV1 signal) consists of a magnet and MRE (Magneto Resistance Element).
The exhaust camshaft has a timing rotor for the camshaft position sensor. When the camshaft rotates, changes occur in the air gaps between the timing rotor and MRE, which affects the magnetic field. As a result, the resistance of the MRE material fluctuates. The camshaft position sensor converts the camshaft rotation data to pulse signals, uses the pulse signals to determine the camshaft angle, and sends it to the ECM. Then the ECM uses this data to control fuel injection duration, injection timing and the Variable Valve Timing (VVT) system.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0365 | EX. Cam Angle Sensor Signal Malfunction | No exhaust camshaft position sensor signal for 5 seconds at an engine speed of 600 rpm or higher (1 trip detection logic). | ·
Open or short in camshaft position sensor circuit (for exhaust camshaft) ·
Camshaft position sensor (for exhaust camshaft) ·
Exhaust camshaft ·
Valve timing ·
ECM |
Comes on | DTC stored |
| P0367 | EX. Cam Angle Sensor Signal Low | The output voltage of the exhaust camshaft position sensor is less than 0.3 V for 5 seconds or more (1 trip detection logic). | ·
Open or short in camshaft position sensor circuit (for exhaust camshaft) ·
Camshaft position sensor (for exhaust camshaft) ·
ECM |
Comes on | DTC stored |
| P0368 | EX. Cam Angle Sensor Signal High | The output voltage of the exhaust camshaft position sensor is higher than 4.7 V for 5 seconds or more (1 trip detection logic). | ·
Open or short in camshaft position sensor circuit (for exhaust camshaft) ·
Camshaft position sensor (for exhaust camshaft) ·
ECM |
Comes on | DTC stored |
Reference: Inspection using an oscilloscope.
Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>SFI SYSTEM(w/o Air Fuel Ratio Sensor)>P0340
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the GTS on.
Start the engine.
Idle the engine for 10 seconds or more.
Enter the following menus: Powertrain / EFI / Trouble Codes.
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, the system is normal.
Refer to DTC P0335.
Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>SFI SYSTEM(w/o Air Fuel Ratio Sensor)>P0335
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
If no problem is found through this diagnostic troubleshooting procedure, there may be a mechanical problem with the engine.
| *a | Front view of wire harness connector
(to Camshaft Position Sensor (for Exhaust Camshaft)) |
Disconnect the camshaft position sensor (for exhaust camshaft) connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C49-3 (VC) - Body ground | Ignition switch ON | 4.5 to 5.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the camshaft position sensor (for exhaust camshaft) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C49-1 (GEX) - C50-81 (GEX) | Always | Below 1 Ω |
| C49-2 (EGEX) - C50-103 (EGEX) | Always | Below 1 Ω |
| C49-1 (GEX) or C50-81 (GEX) - Body ground | Always | 10 kΩ or higher |
| C49-2 (EGEX) or C50-103 (EGEX) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | OK |
| *b | NG |
| *c | Clearance |
Check the camshaft position sensor (for exhaust camshaft) installation condition.
Camshaft position sensor is installed correctly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the timing rotor of the exhaust camshaft.
Camshaft timing rotor does not have any cracks or deformation.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>SFI SYSTEM(w/o Air Fuel Ratio Sensor)>P0011
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the camshaft position sensor (for exhaust camshaft).
Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>CRANKSHAFT POSITION SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
Start the engine.
Turn the GTS on.
Drive the vehicle in accordance with the driving pattern.
Enter the following menus: Powertrain / EFI / Trouble Codes.
Read the DTCs.
If the engine does not start, replace the ECM.
| Result | Proceed to |
|---|---|
| DTC P0365, P0367 or P0368 is output | A |
| DTC is not output | B |
A
B
Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
Start the engine.
Turn the GTS on.
Drive the vehicle in accordance with the driving pattern.
Enter the following menus: Powertrain / EFI / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTC P0365, P0367 or P0368 is output | B |
A
B
Disconnect the camshaft position sensor (for exhaust camshaft) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C49-3 (VC) - C50-59 (VCG) | Always | Below 1 Ω |
| C49-3 (VC) or C50-59 (VCG) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG