1.CHECK FUEL PUMP OPERATION AND INSPECT FOR FUEL LEAK
Check fuel pump operation.
Disconnect the No. 1 integration relay.
Click hereEngine / Hybrid System>1NR-VE ENGINE CONTROL>INTEGRATION RELAY>REMOVAL
| *a | Component with harness connected
(No. 1 Integration Relay) |
Using a service wire, connect terminals 1D-11 and 1D-5 of the No. 1 integration relay.
Be sure not to connect the wrong terminals. It may cause a malfunction.
Turn the ignition switch to ON, and check that the fuel pump operates.
Do not start the engine.
Inspect for fuel leaks.
Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs. If there is a fuel leak, repair or replace parts as necessary.
Turn the ignition switch off.
Connect the No. 1 integration relay.
Click hereEngine / Hybrid System>1NR-VE ENGINE CONTROL>INTEGRATION RELAY>INSTALLATION
2.INSPECT FUEL PRESSURE
Take precautions to prevent gasoline spillage.
Click hereEngine / Hybrid System>1NR-VE FUEL>FUEL SYSTEM>PRECAUTION
Measure the battery voltage.
11 to 14 V
Disconnect the cable from the negative battery terminal.
Remove the air cleaner assembly.
Click hereEngine / Hybrid System>1NR-VE ENGINE CONTROL>THROTTLE BODY>REMOVAL
Remove the EFI fuel pipe clamp.
Click hereEngine / Hybrid System>1NR-VE FUEL>FUEL INJECTOR>REMOVAL
Disconnect the fuel tube sub-assembly from the fuel delivery pipe.
Click hereEngine / Hybrid System>1NR-VE FUEL>FUEL INJECTOR>REMOVAL
| *1 | Fuel Tube Sub-assembly |
| *a | SST (Hose Band) |
| *b | SST (T-joint) |
| *c | SST (Gauge) |
| *d | SST (Hose Joint) |
| *e | SST (Hose) |
| *f | SST (Fuel Tube Connector) |
| *g | Fuel Delivery Pipe |
Install SST (EFI fuel pressure gauge) as shown in the illustration.
Wipe off any spilt gasoline.
Connect the cable to the negative battery terminal.
Operate the fuel pump.
Click hereEngine / Hybrid System>1NR-VE FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION
Measure the fuel pressure.
319 to 329 kPa (3.3 to 3.4 kgf/cm2, 46 to 48 psi)
If the fuel pressure is greater than the standard, replace the fuel pressure regulator assembly.
If the fuel pressure is less than the standard, check the fuel hoses and connections, fuel pump,fuel filter and fuel pressure regulator assembly.
Turn the ignition switch off.
Connect the No. 1 integration relay.
Click hereEngine / Hybrid System>1NR-VE ENGINE CONTROL>INTEGRATION RELAY>INSTALLATION
Start the engine.
Measure the fuel pressure at idle.
319 to 329 kPa (3.3 to 3.4 kgf/cm2, 46 to 48 psi)
Standard idle speed
Click hereEngine / Hybrid System>1NR-VE ENGINE MECHANICAL>ENGINE>ON-VEHICLE INSPECTION
Stop the engine.
Check that the fuel pressure remains as specified for 5 minutes after the engine stops.
147 to 329 kPa (1.5 kgf/cm2, 21 psi) or more
If the fuel pressure is not as specified, check the fuel pump, fuel pressure regulator assembly and/or fuel injector assemblies.
After checking the fuel pressure, disconnect the cable from the negative (-) battery terminal and carefully remove SST to prevent fuel from spraying.
Connect the fuel tube sub-assembly to the fuel delivery pipe.
Click hereEngine / Hybrid System>1NR-VE FUEL>FUEL INJECTOR>INSTALLATION
Install the EFI fuel pipe clamp.
Click hereEngine / Hybrid System>1NR-VE FUEL>FUEL INJECTOR>INSTALLATION
Install the air cleaner assembly.
Click hereEngine / Hybrid System>1NR-VE ENGINE CONTROL>THROTTLE BODY>INSTALLATION
Inspect for fuel leaks.
Click hereEngine / Hybrid System>1NR-VE FUEL>FUEL SYSTEM>PRECAUTION