Home › Engine / Hybrid System › 1NR-VE ENGINE MECHANICAL › ENGINE › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042273 1NR-VE ENGINE MECHANICAL _0196177 ENGINE G

1NR-VE ENGINE MECHANICAL  ENGINE  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 17801 4.INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

a.

Remove the air cleaner cap sub-assembly.

Click hereEngine / Hybrid System>1NR-VE ENGINE MECHANICAL>ENGINE ASSEMBLY>REMOVAL


b.

Remove the air cleaner filter element sub-assembly.


c.

Visually check that the air cleaner filter element sub-assembly is not excessively damaged or oily. If necessary, replace the air cleaner filter element sub-assembly.

HINT:
·

If there is any foreign matter or clogs in the air cleaner filter element sub-assembly, clean it with compressed air.

·

If any foreign matter or clogs remain even after cleaning the air cleaner filter element sub-assembly with compressed air, replace it.




d.

Install the air cleaner filter element sub-assembly.


e.

Install the air cleaner cap sub-assembly.

Click hereEngine / Hybrid System>1NR-VE ENGINE MECHANICAL>ENGINE ASSEMBLY>INSTALLATION


Hide 16361A 6.INSPECT FAN AND GENERATOR V BELT

Hide 16620 7.INSPECT V-RIBBED BELT TENSIONER ASSEMBLY

a.

Remove the fan and generator V belt.

Click hereEngine / Hybrid System>1NR-VE ENGINE MECHANICAL>DRIVE BELT>REMOVAL


b.

Check that nothing is caught in the V-ribbed belt tensioner assembly by turning it clockwise and counterclockwise. If a malfunction exists, replace the V-ribbed belt tensioner assembly.


c.

Install the fan and generator V belt.

Click hereEngine / Hybrid System>1NR-VE ENGINE MECHANICAL>DRIVE BELT>INSTALLATION


Hide 8.INSPECT VALVE LASH ADJUSTER NOISE

a.

Rev up the engine several times. Check that the engine does not emit unusual noises. If unusual noises occur, warm up the engine and idle it for 30 minutes or more, then perform the preceding inspections.

HINT:

If any defects or problems are found during the preceding inspections, perform valve lash adjuster inspection.

Click hereEngine / Hybrid System>1NR-VE ENGINE MECHANICAL>ENGINE UNIT>INSPECTION



Hide 9.INSPECT IGNITION TIMING

a.

Warm up and stop the engine.


b.

When using the GTS or Techstream:

i.

Connect the GTS or Techstream to the DLC3.


ii.

Start the engine and run it at idle.


iii.

Turn the GTS or Techstream on.


iv.

Enter the following menus: Powertrain / EFI / Data List / Ignition timing advance No.1.

Standard ignition timing:

-10 to 10 degrees BTDC


NOTICE:
·

Turn all electrical systems and the A/C off (w/ Air Conditioning System).

·

Turn all electrical systems off (w/o Air Conditioning System).

·

Check the ignition timing with the cooling fans off.

·

When checking the ignition timing, the transmission should be in neutral or park.




v.

Enter the following menus: Powertrain / EFI / Active Test / Terminal T / ON.


vi.

Monitor IGN Advance of the Data List.

Standard ignition timing:

8 to 12 degrees BTDC


NOTICE:

When checking the ignition timing, the transmission should be in neutral or park.



vii.

Enter the following menus: Powertrain / EFI / Active Test / Terminal T / OFF.


viii.

Check that the ignition timing advances immediately when the engine speed is increased.


ix.

Turn the ignition switch off.


x.

Disconnect the GTS or Techstream from the DLC3.



c.

When not using the GTS or Techstream:

i.
G100891C03
1.177,1.958 1.594,1.563 true 1.583,0.927 1.115,0.438 true 0.063,0.073 0.375,0.271 0.313,0.198 10 false *a 0.979,0.292 1.292,0.49 0.313,0.198 10 false E 0.833,1.938 1.146,2.135 0.313,0.198 10 false EFIT
*a DLC3


Using SST, connect terminals 12 (EFIT) and 4 (E) of the DLC3.

SST
09843-18040  

NOTICE:
·

Be sure to connect the terminals correctly. Failure to do so can damage the engine.

·

Turn all electrical systems and the A/C off (w/ Air Conditioning System).

·

Turn all electrical systems off (w/o Air Conditioning System).

·

Check the ignition timing with the cooling fans off.

·

When checking the ignition timing, the transmission should be in neutral or park.




ii.
A360062

Pull out the wire harness shown in the illustration.

NOTICE:

After checking, wrap the wire harness with tape.



iii.

Connect the clip of the timing light to the wire harness.

NOTICE:

Use a timing light that detects the primary signal.



iv.
A370763C01
0.021,0.073 0.333,0.229 0.313,0.156 10 false *A 0.063,2.323 0.375,2.479 0.313,0.156 10 false *B 2.552,0.396 2.865,0.552 0.313,0.156 10 false *a 2.094,0.594 2.406,0.75 0.313,0.156 10 false *b 2.667,2.594 2.979,2.75 0.313,0.156 10 false *a 2.219,2.802 2.531,2.958 0.313,0.156 10 false *b
*A w/o Air Conditioning System
*B w/ Air Conditioning System
*a TDC
*b 8 to 12 degrees BTDC


Inspect the ignition timing at idle.

Standard ignition timing:

8 to 12 degrees BTDC


NOTICE:

When checking the ignition timing, the transmission should be in neutral or park.


HINT:
·

If the cutout of the crankshaft pulley is positioned within the range *b of the timing chain cover sub-assembly, the ignition timing is within the specified range.

·

After running the engine at 1000 to 1300 rpm for 5 seconds, check that it returns to idle speed.




v.

Disconnect SST from terminals 12 (EFIT) and 4 (E) of the DLC3.


vi.

Inspect the ignition timing at idle.

Standard ignition timing:

-10 to 10 degrees BTDC



vii.

Check that the ignition timing advances immediately when the engine speed is increased.


viii.

Remove the timing light.



Hide 10.INSPECT ENGINE IDLE SPEED

a.

Warm up and stop the engine.


b.

When using the GTS or Techstream:

i.

Connect the GTS or Techstream to the DLC3.


ii.

Start the engine and run it at idle.


iii.

Enter the following menus: Powertrain / EFI / Data List / Engine revolution speed.


iv.

Inspect the engine idle speed.

Standard idle speed:
Manual Transmission:

550 to 650 rpm

Automatic Transmission:

650 to 750 rpm


NOTICE:
·

Turn all electrical systems and the A/C off (w/ Air Conditioning System).

·

Turn all electrical systems off (w/o Air Conditioning System).

·

Inspect the idle speed with the cooling fans off.

·

When checking the idle speed, the transmission should be in neutral or park.




v.

Turn the ignition switch off.


vi.

Disconnect the GTS or Techstream from the DLC3.



c.

When not using the GTS or Techstream:

i.
G100891C04
0.635,1.875 0.948,1.542 true 0.063,0.063 0.375,0.26 0.313,0.198 10 false *a 0.302,1.854 0.615,2.052 0.313,0.198 10 false REV
*a DLC3


Using SST, connect a tachometer probe to terminal 9 (REV) of the DLC3.

NOTICE:

Be sure to connect the tachometer to the correct terminal. Connecting the wrong terminals can cause damage.


SST
09843-18040  


ii.

Turn the ignition switch to ON.


iii.

Inspect the engine idle speed.

Standard idle speed:
Manual Transmission:

550 to 650 rpm

Automatic Transmission:

650 to 750 rpm


NOTICE:
·

Turn all electrical systems and the A/C off (w/ Air Conditioning System).

·

Turn all electrical systems off (w/o Air Conditioning System).

·

Inspect the idle speed with the cooling fans off.

·

When checking the idle speed, the transmission should be in neutral or park.




iv.

Turn the ignition switch off.


v.

Disconnect the tachometer probe from terminal 9 (REV) of the DLC3.



Hide 11.INSPECT COMPRESSION

NOTICE:

Keep the intake manifold and spark plug holes free of foreign matter when measuring the compression pressure.



b.

Warm up and stop the engine.



d.

Disconnect the 4 fuel injector connectors.

NOTICE:

Disable fuel injection in order to prevent catalyst damage due to unburned gasoline.



e.
A360064

Inspect the cylinder compression pressure.

i.

Insert a compression gauge into the spark plug hole.


ii.

Fully open the throttle.


iii.

While cranking the engine, measure the compression pressure.

Standard pressure:

1200 kPa (12.2 kgf/cm2,174 psi)


Minimum pressure:

900 kPa (9.2 kgf/cm2, 131psi)


Difference between each cylinder:

98 kPa (1.0 kgf/cm2, 14.2 psi) or less


NOTICE:
·

Use a fully-charged battery so that the engine speed can be increased to 250 rpm or more.

·

Inspect the other cylinders in the same way.

·

Measure the compression pressure in as short a time as possible.




iv.

If the cylinder compression pressure is low, pour a small amount of engine oil into the cylinder through the spark plug hole, then inspect it again.

HINT:
·

If adding engine oil increases the compression pressure, the piston rings and/or cylinder bore may be worn or damaged.

·

If the compression pressure stays low, a valve may be stuck or seated improperly, or there may be leakage from the cylinder head gasket.





f.

Connect the 4 fuel injector connectors.



h.

Clear the DTCs.

Click hereEngine / Hybrid System>1NR-VE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

NOTICE:

After the inspection, clear the DTCs, check for DTCs again and make sure the normal system code is output.



Hide 12.INSPECT CO/HC

HINT:

This check determines whether or not the idle CO/HC complies with local regulations.


a.

Start the engine.


b.

Keep the engine speed at 2500 rpm for approximately 180 seconds.


c.

Insert the CO/HC meter testing probe at least 40 cm (1.3 ft.) into the tailpipe during idle.


d.

Immediately check the CO/HC concentration during idle and when the engine is running at 2500 rpm.

HINT:

When performing the 2 mode (with the engine idling/running at 2500 rpm) test, the measurement procedures are determined by applicable local regulations.

If the CO/HC concentration does not comply with local regulations, perform troubleshooting in the order given below.



ii.

See the following table for possible causes, then inspect the applicable parts and repair them if necessary.

CO HC Problem Possible Cause
Normal High Rough idle
1.

Faulty ignition:

·

Incorrect timing

·

Fouled, shorted or improperly gapped plugs


2.

Incorrect valve clearance

3.

Leaks in intake or exhaust valves

4.

Leaks in cylinders


Low High Rough idle (Fluctuating HC reading)
1.

Vacuum leaks:

·

PCV hoses

·

Intake manifold

·

Throttle body with motor assembly

·

Brake booster line


2.

Lean mixture causing misfire


High High Rough idle (Black smoke from exhaust)
1.

Restricted air cleaner filter element

2.

Plugged PCV valve

3.

Faulty EFI system:

·

Pressure regulator

·

Engine coolant temperature sensor

·

Mass air flow meter

·

ECM

·

Injector assemblies

·

Throttle body with motor assembly