Home › Engine / Hybrid System › 2NR-VE INTAKE / EXHAUST › EXHAUST MANIFOLD › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042280 2NR-VE INTAKE / EXHAUST _0196225 EXHAUST MANIFOLD A

2NR-VE INTAKE / EXHAUST  EXHAUST MANIFOLD  INSTALLATION  


PROCEDURE

Hide 17168 1.INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

a.
A361310N01
1.302,1.521 1.458,1.719 0.156,0.198 10 false 1 1.219,0.792 1.375,0.99 0.156,0.198 10 false 2 2.625,0.813 2.781,1.01 0.156,0.198 10 false 3

Install the No. 2 exhaust manifold heat insulator with the 3 bolts in the order shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 17173 2.INSTALL EXHAUST MANIFOLD TO HEAD GASKET

a.

Install a new exhaust manifold to head gasket to the cylinder head sub-assembly.


Hide 25051 3.INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

a.
A361312N01
1.594,0.094 1.75,0.292 0.156,0.198 10 false 1 0.958,1.208 1.115,1.406 0.156,0.198 10 true 2 0.26,0.219 0.417,0.417 0.156,0.198 10 false 4 2.292,1.229 2.448,1.427 0.156,0.198 10 true 3 2.688,0.188 2.844,0.385 0.156,0.198 10 true 5

Install the exhaust manifold converter sub-assembly with the 5 new nuts in the order shown in the illustration.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 17167 4.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

a.
A361309N01
0.635,0.031 0.792,0.229 0.156,0.198 10 true 1 2.625,0.031 2.781,0.229 0.156,0.198 10 true 2 2.729,1.219 2.885,1.417 0.156,0.198 10 true 3 1.552,1.667 1.708,1.865 0.156,0.198 10 true 4 0.958,1.427 1.115,1.625 0.156,0.198 10 true 5

Install the No. 1 exhaust manifold heat insulator with the 5 new nuts in the order shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 17118 5.INSTALL MANIFOLD STAY

a.
A361308N01
1.448,1.5 1.604,1.698 0.156,0.198 10 true 1 1.896,1.396 2.052,1.594 0.156,0.198 10 true 2

Install the manifold stay with the 2 bolts in the order shown in the illustration.

Torque:
31 N*m (316 kgf*cm, 23 ft.*lbf)


Hide 45220 6.CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY (for LHD)

Hide 89467B 7.INSTALL AIR FUEL RATIO SENSOR (w/ Air Fuel Ratio Sensor)

Hide 89465 8.INSTALL OXYGEN SENSOR (w/o Air Fuel Ratio Sensor)

Hide 16281 10.CONNECT NO. 4 WATER BY-PASS HOSE

a.
A361311C01
1.063,0.156 1.375,0.354 0.313,0.198 10 false *a 0.271,0.313 0.583,0.51 0.313,0.198 10 false *c 1.24,0.271 1.552,0.469 0.313,0.198 10 false *b
*a Upper Side
*b 90°
*c 2 to 6 mm (0.0787 to 0.2362 in.)


Connect the No. 4 water by-pass hose with the clip as shown in the illustration.

HINT:

Install the clip so that it is positioned as shown in the illustration.



Hide 17451 11.INSTALL EXHAUST PIPE GASKET

a.

Exhaust manifold converter sub-assembly side:

i.
A181728C92
2.813,1.563 2.688,1.563 2.688,1.563 2.385,1.875 true 1.615,3.188 1.99,3.188 1.99,3.188 1.99,2.313 true 1.458,0.656 1.813,0.656 1.813,0.656 1.813,1.115 false 1.313,0.563 1.604,0.781 0.292,0.219 10 false *1 2.854,1.49 3.135,1.698 0.281,0.208 10 false *a 1.448,3.104 1.771,3.344 0.323,0.24 10 false *2
*1 Exhaust Manifold Converter Sub-assembly
*2 Exhaust Pipe Gasket
*a Wooden Block


Using a plastic hammer and wooden block, tap in a new exhaust pipe gasket until each surface is flush with the exhaust manifold converter sub-assembly.

NOTICE:
·

Be sure to install the exhaust pipe gasket in the correct direction.

·

Do not reuse the exhaust pipe gasket.

·

Do not damage the exhaust pipe gasket.

·

Do not push in the exhaust pipe gasket by using the exhaust pipes when connecting it.





b.

Tail exhaust pipe assembly side:

i.

Install a new exhaust pipe gasket to the front exhaust pipe assembly.



Hide 17410 12.SET FRONT EXHAUST PIPE ASSEMBLY

Hide 58151A 13.INSTALL NO. 1 FLOOR HEAT INSULATOR

Hide 17410 14.INSTALL FRONT EXHAUST PIPE ASSEMBLY

a.
A128853

Using a vernier caliper, measure the free length of the compression springs.

Minimum 41.1 mm (1.62 in.)

If the free length is less than the minimum, replace the compression spring.


b.

Connect the front exhaust pipe assembly to the No. 2 exhaust pipe support.


c.
A361328C01
2.656,0.76 2.948,0.615 false 2.708,0.99 2.948,1.167 false 2.281,0.958 2.458,0.344 true 2.958,0.5 3.271,0.698 0.313,0.198 10 false *1 2.958,1.156 3.271,1.354 0.313,0.198 10 false *2 2.479,0.198 2.792,0.396 0.313,0.198 10 false *3 0.5,1.5 0.813,1.698 0.313,0.198 10 false *a
*1 Exhaust Manifold Converter Sub-assembly
*2 Front Exhaust Pipe Assembly
*3 Exhaust Pipe Gasket
*a Space between flanges: 8.5 mm (0.335 in.)


Install the front exhaust pipe assembly with the 4 bolts, 2 new nuts and 2 compression springs.

Torque:
Exhaust manifold converter sub-assembly side : 46.5 N*m (474 kgf*cm, 34 ft.*lbf)
Tail exhaust pipe assembly side : 19 N*m (194 kgf*cm, 14 ft.*lbf)

HINT:

After installation, check that the space between the flanges of the exhaust manifold converter sub-assembly and front exhaust pipe assembly are consistent front-to-rear and left-to-right.



Hide 89465A 15.INSTALL NO. 2 OXYGEN SENSOR (w/ Air Fuel Ratio Sensor)

Hide 17.INSPECT FOR COOLANT LEAK

Hide 18.INSPECT FOR EXHAUST GAS LEAK

Hide 51473A 19.INSTALL ENGINE SIDE COVER SUB-ASSEMBLY RH

Hide 51443 20.INSTALL NO. 2 ENGINE UNDER COVER (w/ No. 2 Engine Under Cover)