Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2015.08
RM19Y0E _58 Vehicle Interior _003010 SUPPLEMENTAL RESTRAINT SYSTEMS _0015213 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1800/51  Short in Driver Side Squib Circuit  B1801/51  Open in Driver Side Squib Circuit  


DESCRIPTION

The driver side squib circuit consists of the airbag ECU assembly, the spiral cable sub-assembly and the horn button assembly.

The circuit signals the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the driver side squib circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1800/51 Short in Driver Side Squib Circuit One of the following conditions is met:
·

Short in driver side squib circuit

·

Driver side squib malfunction

·

Spiral cable sub-assembly malfunction

·

Airbag ECU assembly malfunction


·

Horn button assembly (driver side squib)

·

Spiral cable sub-assembly

·

Airbag ECU assembly

·

Instrument panel wire


DTC is output in check mode
B1801/51 Open in Driver Side Squib Circuit One of the following conditions is met:
·

Open in driver side squib circuit

·

Driver side squib malfunction

·

Spiral cable sub-assembly malfunction

·

Airbag ECU assembly malfunction


·

Horn button assembly (driver side squib)

·

Spiral cable sub-assembly

·

airbag ECU assembly

·

Instrument panel wire


DTC is output in check mode

WIRING DIAGRAM

C285965E04
0.833,3.052 2.479,3.563 1.646,0.51 10 false Horn Button Assembly (Driver Side Squib) 3.042,2.896 3.583,3.094 0.542,0.198 10 false E63 3,3.073 3.938,3.667 0.938,0.594 10 false Spiral Cable Sub-assembly 4.813,3.896 6.438,4.271 1.625,0.375 10 false Airbag ECU Assembly 4.833,3.708 5.375,3.906 0.542,0.198 10 false E76 2.458,2.24 2.615,2.438 0.156,0.198 10 false 1 2.458,1.417 2.615,1.615 0.156,0.198 10 false 2 3.75,1.406 3.906,1.604 0.156,0.198 10 false 1 3.76,2.25 3.917,2.448 0.156,0.198 10 false 2 4.51,1.385 4.729,1.604 0.219,0.219 10 false 17 4.51,2.24 4.74,2.49 0.229,0.25 10 false 18 4.792,2.344 5.052,2.542 0.26,0.198 10 false D- 4.813,1.479 5.073,1.677 0.26,0.198 10 false D+ 3.469,1.406 3.729,1.604 0.26,0.198 10 false D+ 3.49,2.25 3.75,2.448 0.26,0.198 10 false D- 0.833,2.865 1.375,3.063 0.542,0.198 10 false z5

CAUTION / NOTICE / HINT

NOTICE:
·

When installing the spiral cable sub-assembly and steering wheel, be sure to adjust the spiral cable sub-assembly as it may break if the steering wheel is turned before adjusting the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSTALLATION

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After replacing the airbag ECU assembly, refer to initialization.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



HINT:
·

Perform the simulation method by selecting check mode (Signal Check) using the GTS or Techstream.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE

·

After selecting check mode (Signal Check), perform simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM



PROCEDURE

1.CHECK HORN BUTTON ASSEMBLY (DRIVER SIDE SQUIB)
SST
09843-18061  

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.
C312968C01
0.417,3.167 0.833,3.417 0.417,0.25 0.25,1.354 0.25,1.677 false 2.188,3.208 2.458,3.208 false 2.208,2.635 2.021,2.635 2.021,2.635 1.792,2.969 true 1.208,2.604 1.406,2.604 1.406,2.604 1.688,2.979 true 0.198,1.719 0.51,1.875 0.313,0.156 10 false *1 1.115,1.719 1.427,1.875 0.313,0.156 10 false *2 2.677,1.813 2.99,1.969 0.313,0.156 10 false *3 1.656,2.385 1.969,2.542 0.313,0.156 10 false *4 0.552,2.365 0.865,2.521 0.313,0.156 10 false *a 0.344,1.479 0.656,1.635 0.313,0.156 10 false F 0.583,1.469 0.896,1.625 0.313,0.156 10 false E 1.698,1.469 2.01,1.625 0.313,0.156 10 false D 1.833,1.469 2.146,1.625 0.313,0.156 10 false C 2.375,1.229 2.688,1.385 0.313,0.156 10 false A 2.51,3.125 3.042,3.396 0.531,0.271 10 false SST 2.26,2.542 2.573,2.698 0.313,0.156 10 false 2 1.104,2.521 1.417,2.677 0.313,0.156 10 false 1 0.552,3.198 1.083,3.469 0.531,0.271 10 false z5
*1 Horn Button Assembly (Driver Side Squib)
*2 Spiral Cable Sub-assembly
*3 Airbag ECU Assembly
*4 Connector E
*a Front view of wire harness connector
(to Horn Button Assembly (Driver Side Squib))


Disconnect the connector from the horn button assembly.


d.

Connect the white wire side of SST (resistance 2.1 Ω) to connector E.

CAUTION:

Never connect the tester to the horn button assembly (driver side squib) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert the SST straight into the terminals of the connector.




e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Clear the DTCs.

Body Electrical > A/B > Clear DTCs
50002 587

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR


h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check the DTCs.

Body Electrical > A/B > Trouble Codes
50001 587

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

OK:

DTCs B1800/51 or B1801/51 is not output.


HINT:

Codes other than DTCs B1800/51 and B1801/51 may be output at this time, but they are not related to this check.


Result:
Proceed to
OK
NG




OK

NG

2.CHECK CONNECTOR
2.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the SST from connector E.


d.

Disconnect the connectors from the airbag ECU assembly.


e.
C251617C01
0.313,1.063 0.313,1.427 false 0.229,1.469 0.49,1.656 0.26,0.188 10 *1 2.438,0.906 2.594,1.094 0.156,0.188 10 A 0.865,1.427 1.125,1.615 0.26,0.188 10 *2 2.313,1.323 2.573,1.51 0.26,0.188 10 *3 2.083,1.135 2.24,1.323 0.156,0.188 10 B 1.76,1.146 1.917,1.333 0.156,0.188 10 D 1.604,1.146 1.76,1.333 0.156,0.188 10 C 0.594,1.135 0.75,1.323 0.156,0.188 10 E 0.406,1.135 0.563,1.323 0.156,0.188 10 F
*1 Horn Button Assembly (Driver Side Squib)
*2 Spiral Cable Sub-assembly
*3 Airbag ECU Assembly


Check that the connectors on the airbag ECU assembly side and horn button assembly side are not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.


Result:
Proceed to
OK
NG




OK

3.CHECK DRIVER SIDE SQUIB CIRCUIT

NG

REPLACE HARNESS AND CONNECTOR

3.CHECK DRIVER SIDE SQUIB CIRCUIT
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


c.
C312969C01
0.5,3.292 0.917,3.542 0.417,0.25 1.135,2.969 1.604,2.969 true 1.771,2.969 2.24,2.969 true 0.302,1.073 0.302,1.365 false 0.24,1.406 0.552,1.563 0.313,0.156 10 false *1 1.083,1.406 1.396,1.563 0.313,0.156 10 false *2 2.646,1.5 2.958,1.656 0.313,0.156 10 false *3 1.604,2.458 1.917,2.615 0.313,0.156 10 false *4 0.51,2.333 0.823,2.49 0.313,0.156 10 false *a 0.385,1.177 0.698,1.333 0.313,0.156 10 false F 1.604,1.167 1.917,1.323 0.313,0.156 10 false D 0.583,1.177 0.896,1.333 0.313,0.156 10 false E 1.74,1.167 2.052,1.323 0.313,0.156 10 false C 2.083,1.167 2.396,1.323 0.313,0.156 10 false B 2.438,0.969 2.75,1.125 0.313,0.156 10 false A 0.979,2.896 1.292,3.052 0.313,0.156 10 false 1 2.302,2.885 2.615,3.042 0.313,0.156 10 false 2 0.646,3.333 0.958,3.49 0.313,0.156 10 false z5
*1 Horn Button Assembly (Driver Side Squib)
*2 Spiral Cable Sub-assembly
*3 Airbag ECU Assembly
*4 Connector E
*a Front view of wire harness connector
(to Horn Button Assembly (Driver Side Squib))


Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Condition Specified Condition
z5-1 - Body ground Ignition switch ON Below 1 V
z5-2 - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
z5-1 - z5-2 Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


h.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Tester Connection Specified Condition
z5-1 - z5-2 Always 1 MΩ or higher
z5-1 - Body ground Always 1 MΩ or higher
z5-2 - Body ground Always 1 MΩ or higher



i.

Restore the released activation prevention mechanism of connector B to its original condition.

Result:
Proceed to
OK
NG




OK

4.CHECK DTC

NG

5.CHECK INSTRUMENT PANEL WIRE
4.CHECK DTC
a.
C251575C01
0.385,1.042 0.385,1.323 false 0.313,1.344 0.531,1.542 0.219,0.198 10 *1 2.177,1.313 2.396,1.51 0.219,0.198 10 *3 0.813,1.385 1.031,1.583 0.219,0.198 10 *2
*1 Horn Button Assembly (Driver Side Squib)
*2 Spiral Cable Sub-assembly
*3 Airbag ECU Assembly


Connect the connectors to the horn button assembly and airbag ECU assembly.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs.

Body Electrical > A/B > Clear DTCs
50002 587

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR


e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Body Electrical > A/B > Trouble Codes
50001 587

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

OK:

DTCs B1800/51 or B1801/51 is not output.


HINT:

Codes other than DTCs B1800/51 and B1801/51 may be output at this time, but they are not related to this check.


Result:
Proceed to
OK
NG




OK

NG

5.CHECK INSTRUMENT PANEL WIRE
a.

Disconnect the instrument panel wire connector from the spiral cable sub-assembly.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

C312970C02
4.344,0.615 4.76,0.865 0.417,0.25 2.021,0.24 2.167,0.24 2.167,0.24 2.167,0.656 false 5.25,0.885 5.115,1.302 5.115,1.302 4.938,1.302 true 5.469,0.896 5.563,1.313 5.563,1.313 5.729,1.313 true 1.417,1 1.729,1.156 0.313,0.156 10 false *1 2.729,1.125 3.042,1.281 0.313,0.156 10 false *2 1.833,0.177 2.146,0.333 0.313,0.156 10 false *3 5.417,0.188 5.729,0.344 0.313,0.156 10 false *4 4.5,0.167 4.813,0.323 0.313,0.156 10 false *a 2.542,0.646 2.854,0.802 0.313,0.156 10 false A 2.271,0.844 2.583,1 0.313,0.156 10 false B 1.969,0.844 2.281,1 0.313,0.156 10 false C 1.813,0.844 2.125,1 0.313,0.156 10 false D 1.094,0.844 1.406,1 0.313,0.156 10 false E 0.906,0.844 1.219,1 0.313,0.156 10 false F 4.719,1.219 5.031,1.375 0.313,0.156 10 false D+ 5.771,1.229 6.083,1.385 0.313,0.156 10 false D- 4.438,0.656 4.844,0.865 0.406,0.208 10 false E63
*1 Spiral Cable Sub-assembly *2 Airbag ECU Assembly
*3 Instrument Panel Wire *4 Connector C
*a Front view of wire harness connector
(to Spiral Cable Sub-assembly)
- -


Standard voltage:
Tester Connection Condition Specified Condition
E63-1 (D+) - Body ground Ignition switch ON Below 1 V
E63-2 (D-) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
E63-1 (D+) - E63-2 (D-) Always Below 1 Ω



h.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


i.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
E63-1 (D+) - E63-2 (D-) Always 1 MΩ or higher
E63-1 (D+) - Body ground Always 1 MΩ or higher
E63-2 (D-) - Body ground Always 1 MΩ or higher



j.

Restore the released activation prevention mechanism of connector B to the original condition.

Result:
Proceed to
OK
NG




OK

REPLACE SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE