Home › Engine / Hybrid System › 2NR-VE ENGINE CONTROL › SFI SYSTEM(w/ Air Fuel Ratio Sensor) › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042272 2NR-VE ENGINE CONTROL _0196262 SFI SYSTEM(w/ Air Fuel Ratio Sensor) C

2NR-VE ENGINE CONTROL  SFI SYSTEM(w/ Air Fuel Ratio Sensor)  P0011  IN. DVVT System Advance Malfunction  P0012  IN. DVVT System Retard/Delay Malfunction  


DESCRIPTION

The Variable Valve Timing (VVT) system includes the ECM, Oil Control Valve (OCV) and VVT controller (camshaft timing sprocket assembly). The ECM sends a target duty-cycle control signal to the OCV. This control signal regulates the oil pressure supplied to the VVT controller. Camshaft timing control is performed according to engine operating conditions such as the intake air volume, throttle valve position and engine coolant temperature. The ECM controls the OCV based on the signals transmitted by several sensors. The VVT controller regulates the intake camshaft angle using oil pressure through the OCV. As a result, the relative positions of the camshaft and crankshaft are optimized, the engine torque and fuel economy improve, and the exhaust emissions decrease under overall driving conditions. The ECM detects the actual intake valve timing using signals from the camshaft and crankshaft position sensors, and performs feedback control. This is how the target intake valve timing is verified by the ECM.

A192077E74
2.563,4.573 2.844,4.271 2.844,4.271 3.604,4.271 false 3.177,4.823 3.323,5.052 3.323,5.052 3.854,5.052 false 4.479,0.813 6.094,1.167 1.615,0.354 10 false Camshaft Position Sensor 4.479,1.323 6.188,1.708 1.708,0.385 10 false Crankshaft Position Sensor 0.073,0.063 1.76,0.458 1.688,0.396 12 false VVT System: 2.333,1.99 3.573,2.365 1.24,0.375 10 false Target Valve Timing 2.333,1.292 3.552,1.667 1.219,0.375 10 false Actual Valve Timing 2.688,2.698 3.385,3.073 0.698,0.375 10 false Correction 2.823,3.208 3.167,3.521 0.344,0.313 10 false ECM 1.604,3.76 5.771,4.188 4.167,0.427 10 false Camshaft Timing Oil Control Valve Assembly (for Intake Camshaft) 0.167,2.688 0.927,3 0.76,0.313 10 false Duty Cycle 4.479,1.823 6.667,2.208 2.188,0.385 10 false Intake Air Flow Meter Assembly 4.479,2.854 6.698,3.188 2.219,0.333 10 false Engine Coolant Temperature Sensor 4.479,2.344 6.073,2.708 1.594,0.365 10 false Throttle Position Sensor 4.479,3.354 6.063,3.688 1.583,0.333 10 false Vehicle Speed Sensor 0.375,4.271 1.979,4.656 1.604,0.385 10 false Engine Oil Pressure 3.656,4.188 5.427,4.625 1.771,0.438 10 false Camshaft Timing Gear 3.885,4.958 5.333,5.552 1.448,0.594 10 false Intake Camshaft

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0011 IN. DVVT System Advance Malfunction Intake valve timing is stuck at a certain value when in the advance range (1 trip detection logic).
·

Valve timing

·

Camshaft timing oil control valve assembly (for intake camshaft)

·

Camshaft timing oil control valve filter

·

Camshaft timing gear assembly

·

ECM


Comes on DTC stored
P0012 IN. DVVT System Retard/Delay Malfunction Intake valve timing is stuck at a certain value when in the retard range (2 trip detection logic).
·

Valve timing

·

Camshaft timing oil control valve assembly (for intake camshaft)

·

Camshaft timing oil control valve filter

·

Camshaft timing gear assembly

·

ECM


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

A232050E46
6.74,2.625 6.333,3.458 6.333,3.458 6.25,3.458 false 4.167,2.646 3.833,3.479 3.833,3.479 3.771,3.479 false 1.365,2.354 1.604,2.531 0.24,0.177 10 [A] 1.885,2.01 2.083,2.198 0.198,0.188 10 [B] 3.01,1 3.26,1.208 0.25,0.208 10 [C] 4.052,2.271 4.333,2.458 0.281,0.188 10 [D] 4.281,3.135 4.521,3.281 0.24,0.146 10 [E] 5.458,2.25 5.74,2.458 0.281,0.208 10 [F]* 6.615,2.271 6.833,2.5 0.219,0.229 10 [G] 6.813,3.146 7.021,3.365 0.208,0.219 10 [H] 0.177,2.313 1.146,2.646 0.969,0.333 10 Ignition Switch ON 0.708,2.052 1.094,2.24 0.385,0.188 10 Idling 0.177,1.094 1.135,1.438 0.958,0.344 10 Approximately 60 km/h 0.167,0.375 1.115,0.542 0.948,0.167 10 Vehicle Speed 1.615,2.771 2.417,2.969 0.802,0.198 10 Warming up 2.563,2.771 3.802,2.917 1.24,0.146 10 10 minutes or more 2.615,3.396 3.906,3.573 1.292,0.177 10 3 minutes or more 2.375,0.021 6.979,0.229 4.604,0.208 10 *: Repeat the pattern of accelerating the vehicle from rest to approximately 5.104,3.365 6.292,3.542 1.188,0.177 10 3 minutes or more 2.385,0.188 6.51,0.594 4.125,0.406 10 60 km/h (depress the accelerator pedal by a large amount) and then decelerating the vehicle 10 to 15 times.

1.

Connect the GTS or Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS or Techstream on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS or Techstream on [A].

6.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].

7.

Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


8.

Idle the engine for 3 minutes or more [D].

9.

Enter the following menus: Powertrain / EFI / Trouble Codes [E].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Repeat the pattern of accelerating the vehicle from rest to approximately 60 km/h (37 mph) and then decelerating the vehicle 10 to 15 times [F].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Depress the accelerator pedal by a large amount.


12.

Idle the engine for 3 minutes or more [G].

13.

Enter the following menus: Powertrain / EFI / Trouble Codes [H].

14.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, the system is normal.




PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (DTC P0011 OR P0012)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Enter the following menus: Powertrain / EFI / Trouble Codes.


e.

Read the DTCs.


Result:
Result Proceed to
DTC P0011 or P0012 is output A
DTC P0011 or P0012 and other DTCs are output B



A

2.PERFORM ACTIVE TEST USING GTS OR TECHSTREAM (IN.DVVT LINEAR)

B

2.PERFORM ACTIVE TEST USING GTS OR TECHSTREAM (IN.DVVT LINEAR)
a.

Connect the GTS or Techstream to the DLC3.


b.

Start the engine.


c.

Turn the GTS or Techstream on.


d.

Turn the A/C switch on.


e.

Enter the following menus: Powertrain / EFI / Active Test / IN.DVVT Linear.


f.

Check the engine speed while operating the camshaft timing oil control valve assembly (for intake camshaft) using the GTS or Techstream.

OK:
GTS or Techstream Operation Specified Condition
0% Normal engine speed
100% Engine idles roughly or stalls

HINT:

Refer to "Data List / Active Test" [DVVT OCV duty learning value and DVVT actual angle].

Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>SFI SYSTEM(w/ Air Fuel Ratio Sensor)>DATA LIST / ACTIVE TEST



Result:
Proceed to
OK
NG



OK

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011 OR P0012)

NG

5.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)
3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011 OR P0012)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Clear the DTCs.


e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS or Techstream on.


h.

Start the engine and warm it up.


i.

Drive the vehicle in accordance with the driving pattern.


j.

Enter the following menus: Powertrain / EFI / Trouble Codes.


k.

Read the pending DTCs.


Result:
Result Proceed to
DTC is not output A
DTC P0011 or P0012 is output B


HINT:

DTC P0011 or P0012 may be stored when foreign objects in the engine oil are caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. These foreign objects may then be captured by the oil filter.



A

B

4.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT)
4.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT)
a.

Inspect the camshaft timing oil control valve assembly (for intake camshaft).

Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>CAMSHAFT OIL CONTROL VALVE>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT)

5.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)
a.

Remove the cylinder head cover sub-assembly.

Click hereEngine / Hybrid System>2NR-VE ENGINE MECHANICAL>ENGINE UNIT>DISASSEMBLY


b.

Turn the crankshaft pulley, and align its groove with the "0" timing mark of the timing chain cover.


c.

Check that the timing marks of the camshaft timing gear assembly and camshaft timing exhaust gear assembly are at the positions shown in the illustration.

A362207C01
4.802,0.531 4.604,0.292 true 5.667,0.552 5.844,0.281 true 5.219,1.438 5.052,1.135 true 4.469,0.146 4.667,0.344 0.198,0.198 10 false *a 5.823,0.156 6.031,0.354 0.208,0.198 10 false *a 5.229,1.354 5.417,1.531 0.188,0.177 10 false *a 4.583,0.906 4.875,1.083 0.292,0.177 10 false 1.0° 5.865,0.896 6.167,1.083 0.302,0.188 10 false 1.0° 4.302,1.563 4.5,1.75 0.198,0.188 10 false *b
*a Timing Mark *b No. 1 Cylinder at TDC Compression


HINT:

If the timing marks are not as shown, turn the crankshaft one revolution clockwise.


OK:

Timing marks on camshaft timing gear assembly and camshaft timing exhaust gear assembly are aligned as shown in the illustration.



Result:
Proceed to
OK
NG



OK

6.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

NG

8.CHECK ENGINE MECHANICAL SYSTEM
6.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY
a.

Inspect the camshaft timing gear assembly.

Click hereEngine / Hybrid System>2NR-VE ENGINE MECHANICAL>CAMSHAFT>REMOVAL

HINT:

DTC P0011 or P0012 may be stored when foreign objects in the engine oil are caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. Those foreign objects may then be captured by the oil filter.



Result:
Proceed to
OK
NG



OK

7.INSPECT OIL CONTROL VALVE FILTER

NG

REPLACE CAMSHAFT TIMING GEAR ASSEMBLY

7.INSPECT OIL CONTROL VALVE FILTER
a.
A325183

Remove the oil control valve filter.

Click hereEngine / Hybrid System>2NR-VE ENGINE MECHANICAL>ENGINE UNIT>DISASSEMBLY


b.

Check that the filter is not clogged.

OK:

Filter is not clogged.



Result:
Proceed to
OK
NG



OK

8.CHECK ENGINE MECHANICAL SYSTEM

NG

REPLACE OIL CONTROL VALVE FILTER

8.CHECK ENGINE MECHANICAL SYSTEM
a.

Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.


Result:
Proceed to
OK
NG



OK

9.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011 OR P0012)

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

9.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011 OR P0012)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Clear the DTCs.


e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS or Techstream on.


h.

Start the engine and warm it up.


i.

Drive the vehicle in accordance with the driving pattern.


j.

Enter the following menus: Powertrain / EFI / Trouble Codes.


k.

Read the pending DTCs.


Result:
Result Proceed to
DTC is not output A
DTC P0011 or P0012 is output B


HINT:

DTC P0011 or P0012 may be stored when foreign objects in the engine oil are caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. These foreign objects may then be captured by the oil filter.



A

B