Home › Engine / Hybrid System › 2NR-VE ENGINE CONTROL › SFI SYSTEM(w/ Air Fuel Ratio Sensor) › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042272 2NR-VE ENGINE CONTROL _0196262 SFI SYSTEM(w/ Air Fuel Ratio Sensor) C

2NR-VE ENGINE CONTROL  SFI SYSTEM(w/ Air Fuel Ratio Sensor)  P0102  Air Flow Sensor System Open/Low  P0103  Air Flow Sensor System Open/High  


DESCRIPTION

The intake air flow meter assembly is a sensor that measures the amount of air flowing through the throttle valve. The ECM uses this information to determine the fuel injection duration and to provide an appropriate air fuel ratio.

Inside the intake air flow meter assembly, there is a heated platinum wire which is exposed to the flow of intake air. By applying a specific electrical current to the wire, the ECM heats it to a specific temperature. The flow of incoming air cools both the wire and an internal thermistor, affecting their resistance. To maintain a constant current value, the ECM varies the voltage applied to the wire and internal thermistor. The voltage level is proportional to the airflow through the sensor, and the ECM uses it to calculate the intake air volume.

The circuit is constructed so that the platinum hot wire and the temperature sensor create a bridge circuit, and the power transistor is controlled so that the potentials of A and B remain equal to maintain the predetermined temperature.

HINT:

When any of these DTCs is stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is calculated by the ECM, according to the engine speed and throttle valve position. Fail-safe mode continues until a pass condition is detected.


A165052E32
1.417,0.5 1.917,1.5 true 2.625,1.052 2.281,1.479 true 4.833,1.323 4.021,2.198 true 5.104,1.563 5.688,2.208 true 0.115,0.375 1.396,0.802 1.281,0.427 10 Temperature Sensor (Thermistor) 2.167,0.146 2.5,0.417 0.333,0.271 10 +B 2.208,0.563 3.333,0.823 1.125,0.26 10 Power Transistor 2.677,0.958 4.417,1.25 1.74,0.292 10 Platinum Hot Wire (Heater) 1.667,1.49 1.917,1.75 0.25,0.26 10 A 2.458,1.49 2.667,1.75 0.208,0.26 10 B 2.896,1.583 3.917,1.833 1.021,0.25 10 Output Voltage 3.135,2.219 4.917,2.5 1.781,0.281 10 Platinum Hot Wire (Heater) 4.948,2.219 7.083,2.5 2.135,0.281 10 Temperature Sensor (Thermistor)

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0102 Air Flow Sensor System Open/Low The intake air flow meter assembly voltage is less than 0.2 V for 3 seconds (1 trip detection logic).
·

Open or short in intake air flow meter assembly circuit

·

Intake air flow meter assembly

·

ECM


Comes on DTC stored
P0103 Air Flow Sensor System Open/High The mass air flow meter sub-assembly voltage is higher than 4.9 V for 3 seconds (1 trip detection logic).
·

Open or short in intake air flow meter assembly circuit

·

Intake air flow meter assembly

·

ECM


Comes on DTC stored

HINT:

When any of these DTCs are output, check the air flow rate using the GTS or Techstream. Enter the following menus: Powertrain / EFI / Data List / Air flow rate.

Air Flow Rate (g/s) Malfunction
Approximately 0.0
·

Open in intake air flow meter assembly power source circuit

·

Open or short in VG circuit


271.0 or more
·

Open in E2G circuit




CONFIRMATION DRIVING PATTERN

1.

Connect the GTS or Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS or Techstream on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS or Techstream on.

6.

Wait for 5 seconds or more.

7.

Enter the following menus: Powertrain / EFI / Trouble Codes.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, the system is normal.




WIRING DIAGRAM

A360375E05
5.813,0.917 6.125,1.083 0.313,0.167 10 false C50 5.813,1.417 6.115,1.594 0.302,0.177 10 false C50 5.823,3.042 6.104,3.208 0.281,0.167 10 false A24 5.854,0.719 6.031,0.875 0.177,0.156 10 false 76 5.865,1.229 6.063,1.406 0.198,0.177 10 false 98 5.865,2.833 6.031,3.01 0.167,0.177 10 false 28 6.125,0.813 6.365,0.969 0.24,0.156 10 false VG 6.146,1.313 6.458,1.49 0.313,0.177 10 false E2G 6.146,3.052 6.49,3.208 0.344,0.156 10 false MRO 4.99,0.813 5.208,0.99 0.219,0.177 10 false VG 5.302,0.813 5.417,0.99 0.115,0.177 10 false 5 4.969,1.323 5.26,1.479 0.292,0.156 10 false E2G 5.302,1.313 5.417,1.479 0.115,0.167 10 false 4 4.083,0.51 4.302,0.667 0.219,0.156 10 false +B 3.885,0.5 3.99,0.646 0.104,0.146 10 false 3 1.813,1.5 2.438,1.656 0.625,0.156 10 false EFI-MAIN 0.604,3.927 1.073,4.094 0.469,0.167 10 false Battery 0.427,2.385 0.677,2.563 0.25,0.177 10 false EFI 3.208,0.604 3.375,0.76 0.167,0.156 10 false 1J 3.25,0.406 3.344,0.563 0.094,0.156 10 false 3 3.208,1.146 3.427,1.344 0.219,0.198 10 false 1F 3.25,0.958 3.333,1.135 0.083,0.177 10 false 5 0.76,0.604 0.99,0.802 0.229,0.198 10 false 1F 0.76,0.417 0.948,0.604 0.188,0.188 10 false 17 6.365,3.604 6.698,3.771 0.333,0.167 10 false ECM 3.719,2.01 5.938,2.188 2.219,0.177 10 false Intake Air Flow Meter Assembly 3.729,1.813 4.031,1.99 0.302,0.177 10 false C41 1.365,1.885 2.792,2.083 1.427,0.198 10 false No. 1 Integration Relay 0.469,3.042 1.115,3.208 0.646,0.167 10 false FL MAIN

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Read freeze frame data using the GTS or Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK WHETHER DTC OUTPUT RECURS (DTC P0102 OR P0103)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Enter the following menus: Powertrain / EFI / Trouble Codes.


e.

Read the DTCs.


Result:
Result Proceed to
DTC P0102 is output A
DTC P0103 is output B



A

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF INTAKE AIR FLOW METER ASSEMBLY)

B

7.CHECK HARNESS AND CONNECTOR (SENSOR GROUND)
2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF INTAKE AIR FLOW METER ASSEMBLY)
a.
A194097C72
0.302,2.01 0.688,2.271 0.385,0.26 1.656,2.438 0.635,3 true 0.177,0.073 0.625,0.427 0.448,0.354 10 false *a 0.406,2.958 1.042,3.292 0.635,0.333 10 false +B 0.375,2.052 0.813,2.438 0.438,0.385 10 false C41
*a Front view of wire harness connector
(to Intake Air Flow Meter Assembly)


Disconnect the intake air flow meter assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C41-3 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (INTAKE AIR FLOW METER ASSEMBLY - ECM)

NG

5.CHECK HARNESS OR CONNECTOR (INTAKE AIR FLOW METER ASSEMBLY - NO. 1 INTEGRATION RELAY)
3.CHECK HARNESS AND CONNECTOR (INTAKE AIR FLOW METER ASSEMBLY - ECM)
a.

Disconnect the intake air flow meter assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C41-5 (VG) - C50-76 (VG) Always Below 1 Ω
C41-4 (E2G) - C50-98 (E2G) Always Below 1 Ω
C41-5 (VG) or C50-76 (VG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT INTAKE AIR FLOW METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT INTAKE AIR FLOW METER ASSEMBLY
a.

Inspect the intake air flow meter assembly, referring to the On-vehicle Inspection for Mass Air Flow Meter.

Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>MASS AIR FLOW METER>ON-VEHICLE INSPECTION


b.

Inspect the intake air flow meter assembly, referring to the Inspection for Mass Air Flow Meter.

Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>MASS AIR FLOW METER>INSPECTION


c.

Inspect the function of the intake air flow meter assembly.

i.

Connect the GTS or Techstream to the DLC3.


ii.

Turn the ignition switch to ON.


iii.

Turn the GTS or Techstream on.


iv.

Enter the following menus: Powertrain / EFI / Data List / Air flow rate.


v.

Start the engine.


vi.

Check that the Air flow rate value changes when the engine is raced.

OK:

The reading changes.




Result:
Proceed to
OK
NG



OK

NG

REPLACE INTAKE AIR FLOW METER ASSEMBLY

5.CHECK HARNESS OR CONNECTOR (INTAKE AIR FLOW METER ASSEMBLY - NO. 1 INTEGRATION RELAY)
a.

Disconnect the intake air flow meter assembly connector.


b.

Disconnect the No. 1 integration relay connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C41-3 (+B) - 1J-3 Always Below 1 Ω
C41-3 (+B) or 1J-3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT NO. 1 INTEGRATION RELAY

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

6.INSPECT NO. 1 INTEGRATION RELAY
a.

Inspect the No. 1 integration relay.

Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>INTEGRATION RELAY>INSPECTION


Result:
Proceed to
OK
NG



OK

NG

7.CHECK HARNESS AND CONNECTOR (SENSOR GROUND)
a.

Disconnect the intake air flow meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C41-4 (E2G) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE INTAKE AIR FLOW METER ASSEMBLY

NG

8.CHECK HARNESS AND CONNECTOR (INTAKE AIR FLOW METER ASSEMBLY - ECM)
8.CHECK HARNESS AND CONNECTOR (INTAKE AIR FLOW METER ASSEMBLY - ECM)
a.

Disconnect the intake air flow meter assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C41-4 (E2G) - C50-98 (E2G) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR