Home › Engine / Hybrid System › 2NR-VE ENGINE CONTROL › SFI SYSTEM(w/ Air Fuel Ratio Sensor) › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042272 2NR-VE ENGINE CONTROL _0196262 SFI SYSTEM(w/ Air Fuel Ratio Sensor) C

2NR-VE ENGINE CONTROL  SFI SYSTEM(w/ Air Fuel Ratio Sensor)  P0135  Oxygen (A/F) Sensor Heater Circuit (Bank 1 Sensor 1)  


DESCRIPTION

Refer to DTC P2195.

Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>SFI SYSTEM(w/ Air Fuel Ratio Sensor)>P2195

HINT:
·

When any of these DTCs is stored, the ECM enters fail-safe mode. The ECM turns off the air fuel ratio sensor heater in fail-safe mode. Fail-safe mode continues until the ignition switch is turned off.

·

Although the DTC titles say oxygen sensor, these DTCs relate to the air fuel ratio sensor.

·

The ECM has a pulse width modulated control circuit to adjust the current through the heater. The air fuel ratio sensor heater circuit uses a relay on the +B side of the circuit.

·

Air fuel ratio sensor refers to the sensor closest to the engine assembly.



A365757E01
0.073,0.073 2.667,0.406 2.594,0.333 10 false Reference (System Diagram of Sensor 1): 0.354,0.958 1.323,1.406 0.969,0.448 10 false from Battery 1.448,1.135 1.729,1.323 0.281,0.188 10 false EFI 0.917,3.323 1.417,3.5 0.5,0.177 10 false Ground 1.99,2.177 2.625,2.375 0.635,0.198 10 false EFI-MAIN 3.583,1.854 4.99,2.167 1.406,0.313 10 false Air Fuel Ratio Sensor 3.958,0.646 4.438,0.854 0.479,0.208 10 false Heater 3.958,1.208 4.448,1.427 0.49,0.219 10 false Sensor 4.615,1.406 4.917,1.604 0.302,0.198 10 false AF+ 5.167,1.417 5.458,1.615 0.292,0.198 10 false AF+ 3.563,1.417 3.833,1.615 0.271,0.198 10 false AF- 5.167,2.083 5.458,2.302 0.292,0.219 10 false AF- 5.167,2.635 5.542,2.833 0.375,0.198 10 false MRO 5.167,0.885 5.479,1.083 0.313,0.198 10 false HT 4.625,0.885 5.083,1.083 0.458,0.198 10 false AFM 3.521,0.885 3.833,1.083 0.313,0.198 10 false +B 5.833,3.25 6.292,3.448 0.458,0.198 10 false ECM 6.333,1.5 6.833,1.833 0.5,0.333 10 false Duty Control

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0135 Oxygen (A/F) Sensor Heater Circuit (Bank 1 Sensor 1) Open or short in air fuel ratio sensor heater circuit for 1.28 seconds or more
(1 trip detection logic)
·

Open or short in air fuel ratio sensor heater circuit

·

Air fuel ratio sensor heater

·

ECM


Comes on DTC stored

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS or Techstream. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (AIR FUEL RARIO SENSOR - NO. 1 INTEGRATION RELAY)
a.

Disconnect the air fuel ratio sensor connector.


b.

Remove the No. 1 integration relay connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connections Condition Specified Conditions
C37-2 (+B) - 1J-3 Always Below 1 Ω
C37-2 (+B) or 1J-3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF AIR FUEL RATIO SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF AIR FUEL RATIO SENSOR)
a.
A217280C76
0.635,1.979 1.125,2.271 0.49,0.292 1.969,2.042 2.542,1.865 false 0.208,0.281 0.469,0.49 0.26,0.208 10 false *a 2.583,1.771 2.802,1.948 0.219,0.177 10 false +B 0.76,2.063 1.135,2.302 0.375,0.24 10 false C37
*a Front view of wire harness connector
(to Air Fuel Ratio Sensor)


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connections Switch Condition Specified Conditions
C37-2 (+B) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG




OK

3.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)

NG

3.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
a.

Inspect the air fuel ratio sensor.

Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>AIR FUEL RATIO SENSOR>INSPECTION

Result:
Proceed to
OK
NG




OK

4.CHECK HARNESS AND CONNECTOR (ECM - AIR FUEL RATIO SENSOR)

NG

4.CHECK HARNESS AND CONNECTOR (ECM - AIR FUEL RATIO SENSOR)
a.

Disconnect the ECM connector.


b.

Disconnect the air fuel ratio sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connections Condition Specified Conditions
C50-9 (AFH) - C37-1 (HT) Always Below 1 Ω
C50-9 (AFH) or C37-1 (HT) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR