Home › Engine / Hybrid System › 2NR-VE ENGINE CONTROL › SFI SYSTEM(w/ Air Fuel Ratio Sensor) › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042272 2NR-VE ENGINE CONTROL _0196262 SFI SYSTEM(w/ Air Fuel Ratio Sensor) C

2NR-VE ENGINE CONTROL  SFI SYSTEM(w/ Air Fuel Ratio Sensor)  P0141  Rear Oxygen Sensor Heater Signal  


DESCRIPTION

HINT:

Sensor 2 refers to the sensor farthest from the engine assembly.

Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>SFI SYSTEM(w/ Air Fuel Ratio Sensor)>P0136


HINT:

The ECM provides ON/OFF control circuit to adjust current through the heater. The No. 2 oxygen sensor heater circuit uses a relay on the +B side of the circuit.


A365757E02
0.073,0.073 2.667,0.406 2.594,0.333 10 false Reference (System Diagram of Sensor 2): 0.354,0.958 1.323,1.406 0.969,0.448 10 false from Battery 1.448,1.135 1.729,1.323 0.281,0.188 10 false EFI 0.917,3.323 1.417,3.5 0.5,0.177 10 false Ground 1.99,2.177 2.625,2.375 0.635,0.198 10 false EFI-MAIN 3.479,1.875 4.948,2.208 1.469,0.333 10 false No. 2 Oxygen Sensor 3.958,0.646 4.438,0.854 0.479,0.208 10 false Heater 3.958,1.208 4.448,1.427 0.49,0.219 10 false Sensor 4.615,1.406 4.917,1.604 0.302,0.198 10 false + 5.167,1.417 5.458,1.615 0.292,0.198 10 false OX 3.646,1.417 3.917,1.615 0.271,0.198 10 false E 5.167,2.083 5.458,2.302 0.292,0.219 10 false OX- 5.167,2.635 5.542,2.833 0.375,0.198 10 false MRO 5.167,0.885 5.479,1.083 0.313,0.198 10 false HT 4.625,0.885 5,1.083 0.375,0.198 10 false HTR- 3.417,0.885 3.813,1.083 0.396,0.198 10 false HTR+ 5.833,3.25 6.292,3.448 0.458,0.198 10 false ECM 6.333,1.5 6.833,1.833 0.5,0.333 10 false Duty Control

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0141 Rear Oxygen Sensor Heater Signal Open or short in No. 2 oxygen sensor heater circuit for 1.28 seconds or more (2 trip detection logic)
·

Open or short in No. 2 oxygen sensor circuit

·

No. 2 oxygen sensor heater

·

ECM


Comes on DTC stored

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS or Techstream. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NO. 2 OXYGEN SENSOR - NO. 1 INTEGRATION RELAY)
a.

Disconnect the No. 2 oxygen sensor connector.


b.

Remove the No. 1 integration relay connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connections Condition Specified Conditions
C27-2 (ECHI) - 1J-3 Always Below 1 Ω
C27-2 (ECHI) or 1J-3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT ECM (+B VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT ECM (+B VOLTAGE)
a.
A217280C79
0.635,1.979 1.125,2.271 0.49,0.292 1.969,2.042 2.542,1.865 false 0.208,0.281 0.469,0.49 0.26,0.208 10 false *a 2.583,1.771 3.042,2.021 0.458,0.25 10 false ECHI 0.76,2.063 1.135,2.302 0.375,0.24 10 false C27
*a Front view of wire harness connector
(to No. 2 Oxygen Sensor)


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connections Switch Condition Specified Conditions
C27-2 (ECHI) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG




OK

3.INSPECT NO. 2 OXYGEN SENSOR (HEATER RESISTANCE)

NG

3.INSPECT NO. 2 OXYGEN SENSOR (HEATER RESISTANCE)
a.

Inspect the No. 2 oxygen sensor.

Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>HEATED OXYGEN SENSOR>INSPECTION

Result:
Proceed to
OK
NG




OK

4.CHECK HARNESS AND CONNECTOR (ECM - NO. 2 OXYGEN SENSOR)

NG

4.CHECK HARNESS AND CONNECTOR (ECM - NO. 2 OXYGEN SENSOR)
a.

Disconnect the ECM connector.


b.

Disconnect the No. 2 oxygen sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connections Condition Specified Conditions
C50-8 (OXH1) - C27-1 (IREL) Always Below 1 Ω
C50-8 (OXH1) or C27-1 (IREL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR