Home › Engine / Hybrid System › 2NR-VE ENGINE CONTROL › SFI SYSTEM(w/ Air Fuel Ratio Sensor) › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042272 2NR-VE ENGINE CONTROL _0196262 SFI SYSTEM(w/ Air Fuel Ratio Sensor) C

2NR-VE ENGINE CONTROL  SFI SYSTEM(w/ Air Fuel Ratio Sensor)  P0136  O2 Sensor Circuit Bank 1 Sensor 2  P0137  O2 Sensor Circuit Low Voltage Bank 1 Sensor 2  P0138  O2 Sensor Circuit High Voltage Bank 1 Sensor 2  


DESCRIPTION

In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a TWC (Three-Way Catalytic Converter) is used. For the most efficient use of the TWC, the air fuel ratio must be precisely controlled so that it is always close to the stoichiometric air fuel level. For the purpose of helping the ECM to deliver accurate air fuel ratio control, a No. 2 oxygen sensor is used.

The No. 2 oxygen sensor is located behind the TWC, and detects the oxygen concentration in the exhaust gas. Since the sensor is integrated with the heater that heats the sensing portion, it is possible to detect the oxygen concentration even when the intake air volume is low (the exhaust gas temperature is low).

When the air fuel ratio becomes lean, the oxygen concentration in the exhaust gas is high. The No. 2 oxygen sensor informs the ECM that the post-TWC air fuel ratio is lean (low voltage, i.e. less than 0.45 V).

Conversely, when the air fuel ratio is richer than the stoichiometric air fuel level, the oxygen concentration in the exhaust gas is low. The No. 2 oxygen sensor informs the ECM that the post-TWC air fuel ratio is rich (high voltage, i.e. more than 0.45 V). The No. 2 oxygen sensor has the property of changing its output voltage drastically when the air fuel ratio is close to the stoichiometric level.

The ECM uses the supplementary information from the No. 2 oxygen sensor to determine whether the air fuel ratio after the TWC is rich or lean, and adjusts the fuel injection duration accordingly. Thus, if the No. 2 oxygen sensor is working improperly due to internal malfunctions, the ECM is unable to compensate for deviations in the primary air fuel ratio control.

A349923E04
0.729,2.917 1.063,2.917 true 2.917,2.5 3.167,2.75 3.167,2.75 3.417,2.75 true 2.896,1.25 3.479,1.333 3.479,1.333 3,1.333 true 2.833,2.167 3.083,2.417 3.083,2.417 3.333,2.417 true 2.906,1.792 3.406,1.792 true 3.25,1.083 3.5,0.917 3.5,0.917 3.75,0.917 true 2.26,0.396 4.552,0.594 2.292,0.198 10 false Atmospheric Air 5.219,0.323 6.583,0.542 1.365,0.219 10 false Ideal Air Fuel Mixture 4.563,0.688 5.583,0.875 1.021,0.188 10 false Output Voltage 4.99,2.75 6.958,2.958 1.969,0.208 10 false Richer - Air Fuel Ratio - Leaner 2.229,3 3.104,3.219 0.875,0.219 10 false Exhaust Gas 0.333,2.813 1.104,3.01 0.771,0.198 10 false Cover 3.49,2.667 4.667,2.885 1.177,0.219 10 false Coating (Ceramic) 3.417,2.333 4.333,2.531 0.917,0.198 10 false Heater 3.479,1.708 4.604,2.073 1.125,0.365 10 false Solid Electrolyte (Zirconia Element) 3.531,1.271 4.771,1.583 1.24,0.313 10 false Platinum Electrode 3.802,0.833 4.417,1.052 0.615,0.219 10 false Housing

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0136 O2 Sensor Circuit Bank 1 Sensor 2 Abnormal voltage output:
During active air fuel ratio control, the following conditions (a) and (b) are met for a certain period of time (2 trip detection logic):

(a) No. 2 oxygen sensor voltage does not increase to 0.71 V or higher.

(b) No. 2 oxygen sensor voltage does not decrease to less than 0.21 V.


·

No. 2 oxygen sensor circuit

·

No. 2 oxygen sensor

·

Air fuel ratio sensor

·

Gas leak from exhaust system

·

Fuel pressure

·

Fuel injector assembly

·

PCV valve and hose

·

Intake system


Comes on DTC stored
P0137 O2 Sensor Circuit Low Voltage Bank 1 Sensor 2 Low voltage (open):
During active air fuel ratio control, the following conditions (a) and (b) are met for a certain period of time (2 trip detection logic):

(a) No. 2 oxygen sensor voltage output is less than 0.21 V.

(b) Target air fuel ratio is rich.


·

No. 2 oxygen sensor circuit

·

No. 2 oxygen sensor

·

Air fuel ratio sensor

·

Gas leak from exhaust system


Comes on DTC stored
P0138 O2 Sensor Circuit High Voltage Bank 1 Sensor 2 High voltage (short):
During active air fuel ratio control, the following conditions (a) and (b) are met for a certain period of time (2 trip detection logic):

(a) No. 2 oxygen sensor voltage output is higher than 0.71 V.

(b) Target air fuel ratio is lean.


·

No. 2 oxygen sensor circuit

·

No. 2 oxygen sensor

·

Air fuel ratio sensor

·

ECM


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

HINT:
·

This confirmation driving pattern is used in the "Perform Confirmation Driving Pattern" procedure of the following diagnostic troubleshooting procedure.

·

Performing this confirmation driving pattern will activate the No. 2 oxygen sensor monitor (the catalyst monitor is performed simultaneously). This is very useful for verifying the completion of a repair.



A288927E27
1.333,2.854 1.5,2.854 1.5,2.854 1.729,2.438 false 0.938,0.51 2.167,0.708 1.229,0.198 10 false 105 km/h 1.01,1.385 2.24,1.583 1.229,0.198 10 false 95 km/h 1.208,2.25 2.292,2.458 1.083,0.208 10 false Idling 0.177,2.781 1.406,2.979 1.229,0.198 10 false Ignition Switch ON 2.021,2.417 3.25,2.615 1.229,0.198 10 false [A] 2.646,2.125 3.333,2.469 0.688,0.344 10 false [B] 4,0.729 4.469,1 0.469,0.271 10 false [C] 2.344,2.927 3.573,3.125 1.229,0.198 10 false Warming up 3.531,2.927 4.76,3.125 1.229,0.198 10 false 10 minutes or more 5.01,3.344 5.948,3.563 0.938,0.219 10 false [D]

1.

Connect the GTS or Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS or Techstream on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS or Techstream on [A].

6.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].

7.

With the transmission in 4th gear or more, drive the vehicle at 95 to 105 km/h (59 to 65 mph) for 10 minutes or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


8.

Enter the following menus: Powertrain / EFI / Trouble Codes [D].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, the system is normal.




WIRING DIAGRAM

A360376E08
0.75,0.604 1.063,0.802 0.313,0.198 10 false 1F 0.75,0.417 0.948,0.604 0.198,0.188 10 false 17 2.802,0.604 3.115,0.802 0.313,0.198 10 false 1J 2.833,0.438 2.99,0.635 0.156,0.198 10 false 3 2.792,1.146 3.104,1.344 0.313,0.198 10 false 1F 2.844,0.958 3,1.156 0.156,0.198 10 false 5 1.823,1.469 3.052,1.667 1.229,0.198 10 false EFI-MAIN 1.208,1.781 2.615,2.177 1.406,0.396 10 false No. 1 Integration Relay 0.417,2.563 0.875,2.76 0.458,0.198 10 false EFI 0.438,3.198 1.052,3.458 0.615,0.26 10 false FL MAIN 0.594,3.917 1.156,4.219 0.563,0.302 10 false Battery 3.635,0.5 4.052,0.719 0.417,0.219 10 false ECHI 3.448,0.5 3.604,0.698 0.156,0.198 10 false 2 4.448,0.5 4.896,0.74 0.448,0.24 10 false IREL 4.854,0.51 5.01,0.708 0.156,0.198 10 false 1 3.635,1.167 3.792,1.365 0.156,0.198 10 false - 3.458,1.167 3.615,1.365 0.156,0.198 10 false 4 4.656,1.156 4.813,1.354 0.156,0.198 10 false + 4.854,1.146 5.01,1.344 0.156,0.198 10 false 3 3.604,1.719 3.927,1.917 0.323,0.198 10 false C27 3.906,1.719 4.948,2.01 1.042,0.292 10 false Oxygen Sensor 3.177,4.188 3.979,4.448 0.802,0.26 10 false *:Shielded 6.375,3.615 6.833,3.813 0.458,0.198 10 false ECM 5.802,3.042 6.26,3.24 0.458,0.198 10 false A24 5.854,2.865 6.167,3.063 0.313,0.198 10 false 28 6.135,3.052 6.594,3.25 0.458,0.198 10 false MRO 6.125,2.635 6.583,2.833 0.458,0.198 10 false OX- 5.802,2.625 6.26,2.823 0.458,0.198 10 false C50 5.854,2.458 6.167,2.656 0.313,0.198 10 false 51 6.135,1.26 6.448,1.458 0.313,0.198 10 false OX 5.802,1.25 6.26,1.448 0.458,0.198 10 false C50 5.854,1.073 6.167,1.271 0.313,0.198 10 false 30 6.125,0.594 6.531,0.813 0.406,0.219 10 false OXH1 5.792,0.594 6.25,0.792 0.458,0.198 10 false C50 5.896,0.417 6.052,0.615 0.156,0.198 10 false 8 5.354,2.875 5.51,3.073 0.156,0.198 10 false *

CAUTION / NOTICE / HINT

HINT:

Malfunctioning areas can be identified by performing the Control the Injection Volume function provided in the Active Test. The Control the Injection Volume function can help to determine whether the air fuel ratio sensor, No. 2 oxygen sensor and other potential trouble areas are malfunctioning.

The following instructions describe how to conduct the Control the Injection Volume operation using the GTS or Techstream.

1.

Connect the GTS or Techstream to the DLC3.

2.

Start the engine.

3.

Turn the GTS or Techstream on.

4.

Warm up the engine and run the engine at an engine speed of 2500 rpm for approximately 90 seconds.

5.

Enter the following menus: Powertrain / EFI / Active Test / Control the Injection Volume / All Data / AFS Voltage B1S1 and O2S B1S2.

6.

Perform the Active Test operation with the engine idling (press the 12.5% or -12.5% button to change the fuel injection volume).

7.

Monitor the output voltages of the air fuel ratio and No. 2 oxygen sensors (AFS Voltage B1S1 and O2S B1S2) displayed on the GTS or Techstream.



HINT:
·

The Control the Injection Volume operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

Each sensor reacts in accordance with increases and decreases in the fuel injection volume.



GTS or Techstream Display (Sensor) Injection Volume Status Voltage
AFS Voltage B1S1
(Air fuel ratio)
12.5% Rich Below 3.1 V
-12.5% Lean Higher than 3.4 V
O2S B1S2
(Heated oxygen)
12.5% Rich Higher than 0.55 V
-12.5% Lean Below 0.4 V

NOTICE:

The air fuel ratio sensor has an output delay of a few seconds and the No. 2 oxygen sensor has a maximum output delay of approximately 20 seconds.


A283583E43
5.792,3.781 7.115,4.052 1.323,0.271 10 false - Air fuel ratio sensor 3.823,4.927 4.531,5.104 0.708,0.177 8 false Below 0.4 V 3.208,4.396 4.333,4.615 1.125,0.219 10 false Output Voltage 3.25,3.365 4.542,3.615 1.292,0.25 10 false Injection Volume 3.229,1.292 4.521,1.542 1.292,0.25 10 false Injection Volume 3.24,2.313 4.333,2.521 1.094,0.208 10 false Output Voltage 0.625,1.292 1.917,1.542 1.292,0.25 10 false Injection Volume 0.625,3.365 1.917,3.615 1.292,0.25 10 false Injection Volume 0.594,5.438 1.885,5.688 1.292,0.25 10 false Injection Volume 0.604,7.49 1.896,7.74 1.292,0.25 10 false Injection Volume 3.25,7.49 4.542,7.74 1.292,0.25 10 false Injection Volume 3.25,5.438 4.542,5.688 1.292,0.25 10 false Injection Volume 0.635,2.302 1.823,2.51 1.188,0.208 10 false Output Voltage 0.625,4.396 1.792,4.646 1.167,0.25 10 false Output Voltage 0.552,6.479 1.719,6.729 1.167,0.25 10 false Output Voltage 0.573,8.563 1.74,8.813 1.167,0.25 10 false Output Voltage 3.24,8.563 4.406,8.813 1.167,0.25 10 false Output Voltage 3.25,6.479 4.417,6.729 1.167,0.25 10 false Output Voltage 3.51,4.698 4.542,4.885 1.031,0.188 8 false Higher than 0.55 V 0.927,2.646 1.958,2.833 1.031,0.188 8 false Higher than 3.4 V 1.177,2.885 1.927,3.073 0.75,0.188 8 false Below 3.1 V 1.531,1.594 1.979,1.781 0.448,0.188 8 false 12.5% 1.479,1.833 1.927,2.021 0.448,0.188 8 false -12.5% 3.5,2.604 4.531,2.792 1.031,0.188 8 false Higher than 0.55 V 3.813,2.844 4.521,3.021 0.708,0.177 8 false Below 0.4 V 4.156,1.594 4.604,1.781 0.448,0.188 8 false 12.5% 4.115,1.833 4.563,2.021 0.448,0.188 8 false -12.5% 4.146,3.729 4.594,3.917 0.448,0.188 8 false 12.5% 4.104,3.917 4.552,4.104 0.448,0.188 8 false -12.5% 4.104,5.958 4.552,6.146 0.448,0.188 8 false -12.5% 4.104,8.021 4.552,8.208 0.448,0.188 8 false -12.5% 4.156,5.74 4.604,5.927 0.448,0.188 8 false 12.5% 4.156,7.813 4.604,8 0.448,0.188 8 false 12.5% 1.49,7.813 1.938,8 0.448,0.188 8 false 12.5% 1.49,5.75 1.938,5.938 0.448,0.188 8 false 12.5% 1.5,3.677 1.948,3.865 0.448,0.188 8 false 12.5% 1.448,3.896 1.896,4.083 0.448,0.188 8 false -12.5% 1.448,5.948 1.896,6.135 0.448,0.188 8 false -12.5% 1.438,8.021 1.885,8.208 0.448,0.188 8 false -12.5% 0.844,4.802 2.042,5.052 1.198,0.25 8 false Almost no reaction 0.854,8.938 2.052,9.188 1.198,0.25 8 false Almost no reaction 3.5,8.938 4.698,9.188 1.198,0.25 8 false Almost no reaction 3.49,6.865 4.688,7.115 1.198,0.25 8 false Almost no reaction 0.917,6.771 1.948,6.958 1.031,0.188 8 false Higher than 3.4 V 1.167,7.021 1.917,7.208 0.75,0.188 8 false Below 3.1 V 0.24,2.083 0.396,2.281 0.156,0.198 10 false 1 0.24,4.25 0.396,4.448 0.156,0.198 10 false 2 0.25,6.333 0.406,6.531 0.156,0.198 10 false 3 0.24,8.417 0.396,8.615 0.156,0.198 10 false 4 0.125,0.688 0.573,0.938 0.448,0.25 10 false Case 0.792,0.583 2.802,0.969 2.01,0.385 10 false Air Fuel Ratio Sensor (Sensor 1) Output Voltage 3.5,0.583 5.49,1.021 1.99,0.438 10 false No. 2 Oxygen Sensor (Sensor 2) Output Voltage 5.969,0.583 7.01,1 1.042,0.417 10 false Main Suspected Trouble Area 6.396,2.115 6.552,2.313 0.156,0.198 10 false - 5.802,4.031 7.125,4.469 1.323,0.438 10 false - Air fuel ratio sensor heater 5.802,4.448 7.125,4.885 1.323,0.438 10 false - Air fuel ratio sensor circuit 5.917,5.792 6.833,6.156 0.917,0.365 10 false - No. 2 oxygen sensor 5.927,6.198 6.833,6.594 0.906,0.396 10 false - No. 2 oxygen sensor heater 5.927,6.615 6.833,7.042 0.906,0.427 10 false - No. 2 oxygen sensor circuit 5.927,7.698 6.813,8.104 0.885,0.406 10 false - Fuel injector assembly 5.917,8.115 7.073,8.448 1.156,0.333 10 false - Fuel pressure 5.917,8.365 6.969,9.375 1.052,1.01 10 false - Gas leak from exhaust system (air fuel ratio extremely rich or lean) 2.552,2.75 3,2.938 0.448,0.188 8 false OK 2.5,4.719 2.948,4.906 0.448,0.188 8 false NG 2.552,6.865 3,7.052 0.448,0.188 8 false OK 2.5,8.844 2.948,9.031 0.448,0.188 8 false NG 5.167,2.708 5.615,2.896 0.448,0.188 8 false OK 5.167,4.813 5.615,5 0.448,0.188 8 false OK 5.135,8.854 5.583,9.042 0.448,0.188 8 false NG 5.135,6.771 5.583,6.958 0.448,0.188 8 false NG

·

Following the Control the Injection Volume procedure enables technicians to check and graph the voltage outputs of both the air fuel ratio and No. 2 oxygen sensors.

·

To display the graph, enter the following menus: Powertrain / EFI / Active Test / Control the Injection Volume / All Data / AFS Voltage B1S1 and O2S B1S2; then press the view button.


NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read freeze frame data using the GTS or Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ OUTPUT DTC (DTC P0136, P0137 OR P0138)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Enter the following menus: Powertrain / EFI / Trouble Codes.


e.

Read the DTCs.

HINT:

If any DTCs other than P0136, P0137 and P0138 are output, troubleshoot those DTCs first.



Result:
Result Proceed to
DTC P0138 is output A
DTC P0137 is output B
DTC P0136 is output C
DTC P0136, P0137 or P0138 and other DTCs are output D



A

2.READ VALUE USING GTS OR TECHSTREAM (OUTPUT VOLTAGE OF NO. 2 OXYGEN SENSOR)

B

12.CHECK FOR EXHAUST GAS LEAK

C

10.PERFORM ACTIVE TEST USING GTS OR TECHSTREAM (INJECTION VOLUME)

D

2.READ VALUE USING GTS OR TECHSTREAM (OUTPUT VOLTAGE OF NO. 2 OXYGEN SENSOR)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Start the engine.


e.

Enter the following menus: Powertrain / EFI / Data List / All Data / O2S B1S2.


f.

Allow the engine to idle.


g.

Read the No. 2 oxygen sensor output voltage while idling.


Result:
No. 2 Oxygen Sensor Output Voltage Proceed to
1.0 V or higher A
Less than 1.0 V B



A

3.INSPECT NO. 2 OXYGEN SENSOR (CHECK FOR SHORT)

B

5.PERFORM ACTIVE TEST USING GTS OR TECHSTREAM (INJECTION VOLUME)
3.INSPECT NO. 2 OXYGEN SENSOR (CHECK FOR SHORT)
a.
A209298C08
1.896,1.385 2.5,1.667 true 1.563,1.104 1,0.875 true 1.563,1.365 1.042,1.656 true 0.271,0.177 0.427,0.333 0.156,0.156 10 false *a 2.5,1.625 2.667,1.833 0.167,0.208 10 false + 0.583,0.781 1,1 0.417,0.219 10 false ECHI 0.885,1.635 1,1.833 0.115,0.198 10 false E
*a Component without harness connected
(No. 2 Oxygen Sensor)


Disconnect the No. 2 oxygen sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (ECHI) - 3 (+) Always 10 kΩ or higher
2 (ECHI) - 4 (E) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)

NG

4.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)
a.

Turn the ignition switch off and wait for 5 minutes or more.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C50-8 (OXH1) - C50-30 (OX) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.PERFORM ACTIVE TEST USING GTS OR TECHSTREAM (INJECTION VOLUME)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Start the engine.


e.

Warm up the engine.


f.

Enter the following menus: Powertrain / EFI / Active Test / Injection volume / All Data / AFS Voltage B1S1 and O2S B1S2.


g.

Change the fuel injection volume using the GTS or Techstream, and monitor the voltage output of the air fuel ratio sensor and No. 2 oxygen sensor displayed on the GTS or Techstream.

HINT:
·

The Injection volume operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

The air fuel ratio sensor is displayed as AFS Voltage B1S1, and the No. 2 oxygen sensor is displayed as O2S B1S2 on the GTS or Techstream.

·

The air fuel ratio sensor has an output delay of a few seconds and the No. 2 oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Result:
GTS or Techstream Display (Sensor) Voltage Variation Proceed to
AFS Voltage B1S1 (Air fuel ratio) Alternates between higher than and less than 3.3 V OK
Remains at higher than 3.3 V NG
Remains at less than 3.3 V


HINT:

A normal No. 2 oxygen sensor voltage (O2S B1S2) reacts in accordance with increases and decreases in fuel injection volumes. When the air fuel ratio sensor voltage (AFS Voltage B1S1) remains at either less or higher than 3.3 V despite the No. 2 oxygen sensor indicating a normal reaction, the air fuel ratio sensor is malfunctioning.


A285391E10
3.083,2.938 3.583,2.469 false 2.25,1.094 2.667,1.594 false 4.854,0.167 5,0.167 5,0.167 5.083,0.448 false 5.333,2.219 5.927,1.26 5.927,1.26 5.521,2.417 true 5.646,2.667 5.167,2.417 false 3.833,1.688 3.667,1.615 false 5.917,1.26 5.333,1.594 false 2.146,0.25 2.646,0.5 0.5,0.25 10 false 12.5% 5.979,1.177 6.938,1.625 0.958,0.448 10 false Air Fuel Ratio Sensor Output 3.542,1.031 4.042,1.26 0.5,0.229 10 false -12.5% 1.521,0.958 2.271,1.208 0.75,0.25 10 false Malfunction 3.635,2.385 4.542,2.813 0.906,0.427 10 false No. 2 Oxygen Sensor Output 3.875,1.625 4.375,1.875 0.5,0.25 10 false Normal 1,1.844 1.417,2.094 0.417,0.25 10 false 3.3 V 1.135,2.823 1.469,3.073 0.333,0.25 10 false 1 V 1.125,3.354 1.458,3.604 0.333,0.25 10 false 0 V 5.698,2.594 6.635,2.792 0.938,0.198 10 false Malfunctioning 3.813,0.083 4.938,0.365 1.125,0.281 10 false Injection Volume



OK

6.INSPECT AIR FUEL RATIO SENSOR

NG

7.REPLACE AIR FUEL RATIO SENSOR
6.INSPECT AIR FUEL RATIO SENSOR
HINT:

This air fuel ratio sensor test is to check the air fuel ratio sensor current during the fuel-cut operation. When the sensor is normal, the sensor current will indicate below 2.2 mA in this test.


a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Clear the DTCs.


e.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.


f.

Drive the vehicle at 60 km/h (37 mph) or more for 10 minutes or more.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.



g.

Stop the vehicle.


h.

Enter the following menus: Powertrain / EFI / Data List / All Data / AFS Current B1S1.


i.

Drive the vehicle at 60 km/h (37 mph) or more and decelerate the vehicle for 5 seconds or more. Perform this 3 times.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


A152792E58
1.354,2.51 2.635,2.698 1.281,0.188 10 10 minutes or more 2.969,2.51 4.177,2.698 1.208,0.188 10 5 seconds or more 4.271,2.51 5.469,2.698 1.198,0.188 10 5 seconds or more 5.563,2.51 6.74,2.698 1.177,0.188 10 5 seconds or more 0.156,0.073 1.458,0.292 1.302,0.219 12 Driving Pattern: 0.458,1.427 1.115,1.646 0.656,0.219 10 60 km/h 0.531,2.188 1.063,2.385 0.531,0.198 10 0 km/h


j.

Read the value of the air fuel ratio sensor current while the fuel-cut operation is being performed.

Standard Current:

Less than 2.2 mA


HINT:
·

To measure the air fuel ratio sensor current precisely, perform the fuel-cut operation as long as possible.

·

If it is difficult to measure the air fuel ratio sensor current, use the snapshot function of the GTS or Techstream.




Result:
Proceed to
OK
NG



OK

15.REPLACE NO. 2 OXYGEN SENSOR

NG

7.REPLACE AIR FUEL RATIO SENSOR
7.REPLACE AIR FUEL RATIO SENSOR
a.

Result:
Proceed to
NEXT



NEXT

8.PERFORM CONFIRMATION DRIVING PATTERN
8.PERFORM CONFIRMATION DRIVING PATTERN
a.

Perform Confirmation Driving Pattern.


Result:
Proceed to
NEXT



NEXT

9.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136 OR P0138)
9.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136 OR P0138)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Enter the following menus: Powertrain / EFI / Trouble Codes.


e.

Read the DTCs.


Result:
Result Proceed to
DTC P0136 or P0138 is output A
DTC is not output B



A

B

END

10.PERFORM ACTIVE TEST USING GTS OR TECHSTREAM (INJECTION VOLUME)
a.

Connect the GTS or Techstream to the DLC3.


b.

Start the engine.


c.

Turn the GTS or Techstream on.


d.

Warm up the engine.


e.

Enter the following menus: Powertrain / EFI / Active Test / Injection volume / All Data / O2S B1S2.


f.

Change the fuel injection volume using the GTS or Techstream and monitor the voltage output of the No. 2 oxygen sensor displayed on the GTS or Techstream.

HINT:
·

The Injection volume operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

The No. 2 oxygen sensor has a maximum output delay of approximately 20 seconds.



Standard Voltage:

Fluctuates between 0.4 V or less and 0.55 V or higher.



Result:
Proceed to
OK
NG



OK

11.PERFORM ACTIVE TEST USING GTS OR TECHSTREAM (INJECTION VOLUME)

NG

12.CHECK FOR EXHAUST GAS LEAK
11.PERFORM ACTIVE TEST USING GTS OR TECHSTREAM (INJECTION VOLUME)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Start the engine.


e.

Warm up the engine.


f.

Enter the following menus: Powertrain / EFI / Active Test / Injection volume / All Data / AFS Voltage B1S1 and O2S B1S2.


g.

Change the fuel injection volume using the GTS or Techstream, and monitor the voltage output of the air fuel ratio sensor and No. 2 oxygen sensor displayed on the GTS or Techstream.

HINT:
·

The Injection volume operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

The air fuel ratio sensor is displayed as AFS Voltage B1S1, and the No. 2 oxygen sensor is displayed as O2S B1S2 on the GTS or Techstream.

·

The air fuel ratio sensor has an output delay of a few seconds and the No. 2 oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Result:
GTS or Techstream Display (Sensor) Voltage Variation Proceed to
AFS Voltage B1S1 (Air fuel ratio) Alternates between higher than and less than 3.3 V OK
Remains at higher than 3.3 V NG
Remains at less than 3.3 V


HINT:

A normal No. 2 oxygen sensor voltage (O2S B1S2) reacts in accordance with increases and decreases in fuel injection volumes. When the air fuel ratio sensor voltage (AFS Voltage B1S1) remains either less or higher than 3.3 V despite the No. 2 oxygen sensor indicating a normal reaction, the air fuel ratio sensor is malfunctioning.


A285391E11
3.083,2.938 3.583,2.469 false 2.25,1.094 2.667,1.594 false 4.854,0.167 5,0.167 5,0.167 5.083,0.448 false 5.333,2.219 5.927,1.26 5.927,1.26 5.521,2.417 true 5.646,2.667 5.167,2.417 false 3.833,1.688 3.667,1.615 false 5.917,1.26 5.333,1.594 false 2.146,0.25 2.646,0.5 0.5,0.25 10 false 12.5% 5.979,1.177 6.938,1.625 0.958,0.448 10 false Air Fuel Ratio Sensor Output 3.542,1.031 4.042,1.26 0.5,0.229 10 false -12.5% 1.521,0.958 2.271,1.208 0.75,0.25 10 false Malfunction 3.635,2.385 4.479,2.792 0.844,0.406 10 false No. 2 Oxygen Sensor 3.875,1.625 4.375,1.875 0.5,0.25 10 false Normal 1,1.844 1.417,2.094 0.417,0.25 10 false 3.3 V 1.135,2.823 1.469,3.073 0.333,0.25 10 false 1 V 1.125,3.354 1.458,3.604 0.333,0.25 10 false 0 V 5.698,2.594 6.635,2.792 0.938,0.198 10 false Malfunctioning 3.813,0.083 4.938,0.365 1.125,0.281 10 false Injection Volume



OK

CHECK ENGINE TO DETERMINE CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO (FUEL INJECTOR ASSEMBLY, FUEL SYSTEM, INTAKE SYSTEM, ETC.)

NG

7.REPLACE AIR FUEL RATIO SENSOR
12.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks.



Result:
Proceed to
OK
NG



OK

13.INSPECT NO. 2 OXYGEN SENSOR (HEATER RESISTANCE)

NG

REPAIR OR REPLACE EXHAUST GAS LEAK POINT

13.INSPECT NO. 2 OXYGEN SENSOR (HEATER RESISTANCE)

Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (NO. 2 OXYGEN SENSOR - ECM)

NG

14.CHECK HARNESS AND CONNECTOR (NO. 2 OXYGEN SENSOR - ECM)
a.

Disconnect the No. 2 oxygen sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C27-1 (IREL) - C50-8 (OXH1) Always Below 1 Ω
C27-3 (+) - C50-30 (OX) Always Below 1 Ω
C27-4 (-) - C50-51 (OX-) Always Below 1 Ω
C27-1 (IREL) or C50-8 (OXH1) - Body ground Always 10 kΩ or higher
C27-3 (+) or C50-30 (OX) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

15.REPLACE NO. 2 OXYGEN SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.REPLACE NO. 2 OXYGEN SENSOR

Result:
Proceed to
NEXT



NEXT

16.PERFORM CONFIRMATION DRIVING PATTERN
16.PERFORM CONFIRMATION DRIVING PATTERN
a.

Perform Confirmation Driving Pattern.


Result:
Proceed to
NEXT



NEXT

17.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137 OR P0138)
17.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137 OR P0138)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Enter the following menus: Powertrain / EFI / Trouble Codes.


e.

Read the DTCs.


Result:
Result Proceed to
DTC P0136, P0137 or P0138 is output A
DTC is not output B



A

B

END