Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2016.09
RM19Y0E _54 Brake _002992 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0288382 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C0210/23  RR Wheel Open Wire / Shorted  C0215/24  RL Wheel Open Wire / Shorted  


DESCRIPTION

The speed sensor detects the wheel speed and sends the appropriate signals to the skid control ECU (brake actuator assembly). These signals are used for the anti-lock brake system.

Speed sensor rotors have rows of alternating N and S magnetic poles, and their magnetic fields change when the rotors turn. Each speed sensor detects that magnetic field change and sends a pulse signal to the skid control ECU (brake actuator assembly).

HINT:

When the connectors between the speed sensor and skid control ECU (brake actuator assembly) are connected, the following waveform is output.

C248682E02
1.771,0.667 2.344,0.667 false 1.646,1.365 2.167,1.365 2.167,1.365 2.167,1.594 false 4,0.323 5.74,0.813 1.74,0.49 10 Waveform (Reference): 0.354,1.26 1.875,1.76 1.521,0.5 10 Speed Sensor Rotor 0.844,0.563 2.01,0.99 1.167,0.427 10 Speed Sensor 3.979,0.75 7.083,1.26 3.104,0.51 10 Between Speed Sensor (-) and Body Ground 4.635,2.146 5.875,2.719 1.24,0.573 10 Low Speed 5.573,2.125 6.604,2.635 1.031,0.51 10 High Speed 6.594,1.292 7.104,1.667 0.51,0.375 10 1.4 V 6.594,1.635 7.146,1.979 0.552,0.344 10 0.7 V


DTC No. Detection Item DTC Detection Condition Trouble Area Note
C0210/23 RR Wheel Open Wire / Shorted With ignition switch ON, sneak current, short to ground, or open circuit was detected in speed sensor, and circuit current and voltage
·

Rear speed sensor (Rear axle hub and bearing assembly)

·

Speed sensor circuit

·

Speed sensor rotor (Rear axle hub and bearing assembly)

·

Rear speed sensor installation

·

Skid control ECU (Brake actuator assembly)


-
C0215/24 RL Wheel Open Wire / Shorted With ignition switch ON, sneak current, short to ground, or open circuit was detected in speed sensor, and circuit current and voltage
·

Rear speed sensor (Rear axle hub and bearing assembly)

·

Speed sensor circuit

·

Speed sensor rotor (Rear axle hub and bearing assembly)

·

Rear speed sensor installation

·

Skid control ECU (Brake actuator assembly)


-

DTC Detection Conditions: C0210/23
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition Ignition Switch ON ○ ○
Malfunction Status Sneak current or short to ground was detected in the speed sensor, and circuit current and voltage ○ -
Sneak current or open circuit was detected in the speed sensor, and circuit current and voltage - ○
Detection Time - -
Number of Trips - -

DTC Detection Conditions: C0215/24
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition Ignition Switch ON ○ ○
Malfunction Status Sneak current or short to ground was detected in the speed sensor, and circuit current and voltage ○ -
Sneak current or open circuit was detected in the speed sensor, and circuit current and voltage - ○
Detection Time - -
Number of Trips - -

WIRING DIAGRAM

C326772E04
0.76,1.865 2.219,2.292 1.458,0.427 10 false Rear Speed Sensor LH 0.76,3.635 2.219,4.063 1.458,0.427 10 false Rear Speed Sensor RH 0.75,1.688 2.208,2.115 1.458,0.427 10 false J7 0.75,3.458 2.208,3.885 1.458,0.427 10 false J2 1.042,1.542 2.5,1.969 1.458,0.427 10 false + 1.052,3.302 2.51,3.729 1.458,0.427 10 false + 1.844,3.302 3.302,3.729 1.458,0.427 10 false - 1.854,1.531 3.313,1.958 1.458,0.427 10 false - 0.844,1.406 2.302,1.833 1.458,0.427 10 false 1 0.844,3.177 2.302,3.604 1.458,0.427 10 false 1 2.052,3.156 3.51,3.583 1.458,0.427 10 false 2 2.031,1.396 3.49,1.823 1.458,0.427 10 false 2 5.635,0.813 6.396,1.427 0.76,0.615 10 false 29 5.635,1.438 6.396,2.052 0.76,0.615 10 false 28 5.635,2.604 6.396,3.219 0.76,0.615 10 false 16 5.615,3.188 6.375,3.802 0.76,0.615 10 false 15 5.885,0.823 6.646,1.438 0.76,0.615 10 false RL1 5.885,1.427 6.646,2.042 0.76,0.615 10 false RL0 5.885,2.604 6.646,3.219 0.76,0.615 10 false RR1 5.885,3.198 6.646,3.813 0.76,0.615 10 false RR0 5.521,4.042 7.063,4.448 1.542,0.406 10 false Skid Control ECU (Brake Actuator Assembly) 5.5,3.865 6.26,4.479 0.76,0.615 10 false A13

CAUTION / NOTICE / HINT

NOTICE:

If the skid control ECU (brake actuator assembly) is replaced with a new one, the skid control ECU (brake actuator assembly) makes the shift to test mode automatically when the ignition switch is turned to ON for the first time. Be sure to complete the test mode checks.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE


PROCEDURE

1.READ VALUE USING GTS (RR/RL WHEEL SPEED SENSOR TEMP CUTOUT AND RR/RL WHEEL SPEED SENSOR POWER TEMP CUTOUT)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the GTS on.


d.

Start the engine.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List


f.

According to the display on the GTS, read the Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR wheel speed sensor temp cutout Rear speed sensor RH open detection Normal or Cutout Normal: Normal
Cutout: Momentary interruption
Refer to DTC C0210/23.
RL wheel speed sensor temp cutout Rear speed sensor LH open detection Normal or Cutout Normal: Normal
Cutout: Momentary interruption
Refer to DTC C0215/24.
RR wheel speed sensor power temp cutout Rear speed sensor RH voltage open detection Normal or Cutout Normal: Normal
Cutout: Momentary interruption
Refer to DTC C0210/23.
RL wheel speed sensor power temp cutout Rear speed sensor LH voltage open detection Normal or Cutout Normal: Normal
Cutout: Momentary interruption
Refer to DTC C0215/24.


g.

Check for instantaneous interruption of wire harness and connector when the vehicle is stopped and running.

OK:

No instantaneous interruption


NOTICE:

Check for an instantaneous interruption before disconnecting the sensors and connectors.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (WHEEL SPEED RR/RL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.READ VALUE USING GTS (WHEEL SPEED RR/RL)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the GTS on.


d.

Start the engine.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List


f.

According to the display on the GTS, read the Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Wheel speed RR Rear speed sensor RH reading Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Wheel speed RL Rear speed sensor LH reading Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations


g.

Check that there is no difference between the speed value output from the speed sensor displayed on the GTS and the speed value displayed on the speedometer when driving the vehicle.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire inflation and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>OPERATION CHECK


OK:

The speed value displayed on the GTS is the same as the a speed indicated on the speedometer tester (calibrated chassis dynamometer).


Result:
Proceed to
OK
NG




OK

3.PERFORM TEST MODE

NG

5.CHECK REAR SPEED SENSOR INSTALLATION
3.PERFORM TEST MODE
a.

Using the GTS, perform the speed sensor check under the Test Mode check, and check for Test Mode code and DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE

OK:

Both Test Mode codes and DTCs are normal.



Result:
Proceed to
OK
NG



OK

4.RECONFIRM DTC

NG

5.CHECK REAR SPEED SENSOR INSTALLATION
4.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 20 km/h (12 mph).


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Result:
Result Proceed to
DTC is not output A
DTC is output B


HINT:

If troubleshooting has been carried out according to the problem symptoms table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE




A

B

11.REPLACE REAR SPEED SENSOR
5.CHECK REAR SPEED SENSOR INSTALLATION
a.
C108871C02
0.708,1.365 0.99,1.667 false 0.094,0.125 0.51,0.469 0.417,0.344 10 *1 1.031,1.625 1.448,1.969 0.417,0.344 10 *a 0.406,1.74 0.823,2.083 0.417,0.344 10 *b 2.729,1.823 3.146,2.167 0.417,0.344 10 *c
*1 Rear Speed Sensor
*a No clearance
*b CORRECT
*c INCORRECT


Turn the ignition switch off.


b.

Check the rear speed sensor installation.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR>INSTALLATION

OK:

The installation bolt is tightened properly. There is no clearance between the sensor and rear axle housing.


Result:
Proceed to
OK
NG




OK

6.CHECK SPEED SENSOR TIP

NG

INSTALL REAR SPEED SENSOR CORRECTLY

6.CHECK SPEED SENSOR TIP
a.

Turn the ignition switch off.



c.

Check the speed sensor tip.

OK:

No scratches, oil or foreign matter on the sensor tip.


NOTICE:

Do not replace the speed sensor if no damage to the speed sensor tip is found.


HINT:
·

If the sensor is contaminated with oil or other foreign material, clean the sensor.

·

If there is iron powder sticking to the rotor, this will result in a malfunction. Confirm that the rotor is not contaminated with foreign material before replacing the sensor.



Result:
Proceed to
OK
NG




OK

7.CHECK SKID CONTROL SENSOR ROTOR

NG

CLEAN OR REPLACE REAR SPEED SENSOR

7.CHECK SKID CONTROL SENSOR ROTOR
a.

Remove the skid control sensor rotor.

Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE SHAFT>REMOVAL


b.

Check the rear skid control sensor rotor.

OK:

No scratches, oil or foreign matter on the rotors.



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - REAR SPEED SENSOR)

NG

CLEAN OR REPLACE SPEED SENSOR ROTOR

8.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - REAR SPEED SENSOR)
a.

Turn the ignition switch off.


b.

Disconnect the A13 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the J2*1 or J7*2 rear speed sensor connector.

*1: for RH

*2: for LH



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open)(for LH):
Tester Connection Condition Specified Condition
A13-29 (RL1) -J7-1 (+) Always Below 1 Ω
A13-28 (RL0) - J7-2 (-) Always Below 1 Ω


Standard Resistance (Check for Open)(for RH):
Tester Connection Condition Specified Condition
A13-16 (RR1) - J2-1 (+) Always Below 1 Ω
A13-15 (RR0) - J2-2 (-) Always Below 1 Ω


Standard Resistance (Check for Short)(for LH):
Tester Connection Condition Specified Condition
A13-29 (RL1) - Body ground Always 10 kΩ or higher
A13-28 (RL0) - Body ground Always 10 kΩ or higher


Standard Resistance (Check for Short)(for RH):
Tester Connection Condition Specified Condition
A13-16 (RR1) - Body ground Always 10 kΩ or higher
A13-15 (RR0) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

9.CHECK TERMINAL VOLTAGE (POWER SOURCE TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK TERMINAL VOLTAGE (POWER SOURCE TERMINAL)
a.
C364675C01
2.677,0.823 3.031,1.063 0.354,0.24 2.688,1.125 3.042,1.365 0.354,0.24 2.792,0.865 3.104,1.063 0.313,0.198 10 false J2 2.802,1.167 3.115,1.365 0.313,0.198 10 false J7 0.188,0.188 0.563,0.458 0.375,0.271 10 false *a 3.115,0.865 3.354,1.115 0.24,0.25 10 false *A 3.125,1.156 3.365,1.375 0.24,0.219 10 false *B
*A for RH
*B for LH
*a Front view of wire harness connector
(to Speed Sensor)


Reconnect the A13 skid control ECU (brake actuator assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
J2-1 (+) - Body ground Ignition switch ON 5.7 to 14 V
J7-1 (+) - Body ground Ignition switch ON 5.7 to 14 V


Result:
Proceed to
OK
NG




OK

10.RECONFIRM DTC

NG

REPLACE REAR SPEED SENSOR

10.RECONFIRM DTC
a.

Reconnect the J2*1 or J7*2 front speed sensor connector.

*1: for RH

*2: for LH




c.

Turn the ignition switch off.


d.

Start the engine.


e.

Drive the vehicle at a speed of 20 km/h (12 mph).


f.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Result:
Result Proceed to
DTC is output A
DTC is not output B




A

11.REPLACE REAR SPEED SENSOR

B

11.REPLACE REAR SPEED SENSOR
a.

Turn the ignition switch off.


b.

Replace the rear speed sensor.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR>REMOVAL

Result:
Proceed to
NEXT




NEXT

12.RECONFIRM DTC
12.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 20 km/h (12 mph).


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Result:
Result Proceed to
DTC is output A
DTC is not output B




A

13.REPLACE SKID CONTROL SENSOR ROTOR

B

END

13.REPLACE SKID CONTROL SENSOR ROTOR
a.

Remove the skid control sensor rotor.

Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE SHAFT>REMOVAL


b.

Check the rear skid control sensor rotor.

OK:

No scratches, oil or foreign matter on the rotors.



Result:
Proceed to
NEXT



NEXT

14.RECONFIRM DTC
14.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 20 km/h (12 mph).


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Result:
Result Proceed to
DTC is output A
DTC is not output B


HINT:

If troubleshooting has been carried out according to the problem symptoms table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE




A

B

END