Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2016.09
RM19Y0E _54 Brake _002992 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0288382 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  Slip Indicator Light Remains ON  


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.

The slip indicator light blinks during VSC and/or TRC operation.

If a malfunction is detected, the slip indicator light comes on to warn the driver.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DIAGNOSIS SYSTEM

WIRING DIAGRAM

C339505E01
0.938,1.01 1.854,1.427 0.917,0.417 10 false CANL 5.948,1.01 6.865,1.427 0.917,0.417 10 false CANL 5.958,3.031 6.875,3.448 0.917,0.417 10 false CANH 0.917,3.031 1.833,3.448 0.917,0.417 10 false CANH 1.417,0.833 2.333,1.25 0.917,0.417 10 false 8 1.406,2.823 2.323,3.24 0.917,0.417 10 false 9 5.708,0.833 6.625,1.25 0.917,0.417 10 false 10 5.708,2.813 6.625,3.229 0.917,0.417 10 false 22 0.177,3.719 1.094,4.135 0.917,0.417 10 false E34 0.125,3.885 2.073,4.292 1.948,0.406 10 false Combination Meter Assembly 5.563,3.677 6.479,4.094 0.917,0.417 10 false A13 5.469,3.865 7.021,4.438 1.552,0.573 10 false Skid Control ECU (Brake Actuator Assembly) 0.771,4.469 2.531,4.729 1.76,0.26 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:

If the skid control ECU (brake actuator assembly) is replaced with a new one, the skid control ECU (brake actuator assembly) makes the shift to test mode automatically when the ignition switch is turned to ON for the first time. Be sure to complete the test mode checks.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
DTC is not output. A
DTC is output. B



A

2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED

B

2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake actuator assembly) connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

3.INSPECT BATTERY

NG

CONNECT CONNECTOR TO ECU CORRECTLY

3.INSPECT BATTERY
a.

Check the battery voltage.

Standard voltage:

11 to 14 V


Result:
Proceed to
OK
NG




OK

4.PERFORM ACTIVE TEST USING GTS (SLIP INDICATOR)

NG

4.PERFORM ACTIVE TEST USING GTS (SLIP INDICATOR)
a.

Perform an Active Test of the combination meter assembly using the GTS.

OK:

The slip indicator light turns on or off in accordance with the Active Test operation.


Result:
Proceed to
OK
NG




OK

NG