Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2016.10–2018.05
RM32K0E _51 Engine / Hybrid System _059620 HYBRID / BATTERY CONTROL _0292486 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0C3000  Hybrid/EV Battery State of Charge High  


DESCRIPTION

The hybrid vehicle control ECU monitors the system internal operation and will store a DTC and perform fail-safe control if it detects the following malfunction.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0C3000 Hybrid/EV Battery State of Charge High Charging prohibited
Charging of the HV battery continues even after charging is prohibited when the hybrid system is malfunctioning and "Hybrid Battery SOC" has reached the upper limit.
(1 trip detection logic)
·

Hybrid vehicle control ECU

·

HV battery junction block assembly

·

Battery voltage sensor

·

Hybrid battery thermistor (wireharness or connector)

·

Wire harness or connector


Does not come on Master Warning Light:
Comes on

Related Data List
DTC No. Data List
P0C3000
·

Hybrid Battery SOC

·

WIN Control Limit Power

·

Hybrid Battery Current



CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

Apply the parking brake and secure the wheels using chocks.

7.

Fully apply the parking brake and chock all 4 wheels. Firmly depress the brake pedal, turn the power switch on (READY) and shift lever in D. Depress the accelerator pedal to start the engine and increase the engine speed. This will cause the "Hybrid Battery SOC" to increase.

If the charge current drops, release the accelerator pedal and then depress it again to maintain charging.

8.

Select "WIN Control Limit Power" in the Data List and check that charging stops when "WIN Control Limit Power" reaches 0 kW.

9.

Check that charging stops when the Data List item "SOC" reaches the upper limit.

10.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

11.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

Refer to the wiring diagram for DTC P0ABF11.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0ABF11

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A371653

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A371654C01
1.563,1.229 1.333,0.813 true 1.156,0.677 1.469,0.875 0.313,0.198 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
P0C3000 only is output. A
DTCs except P0C3000 are output. B



e.

Turn the power switch off.



A

2.CHECK BATTERY VOLTAGE SENSOR (IGCT VOLTAGE)

B

2.CHECK BATTERY VOLTAGE SENSOR (IGCT VOLTAGE)

OK

3.CHECK HARNESS AND CONNECTOR (BATTERY VOLTAGE SENSOR - HV BATTERY JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY VOLTAGE SENSOR POWER SOURCE CIRCUIT)

3.CHECK HARNESS AND CONNECTOR (BATTERY VOLTAGE SENSOR - HV BATTERY JUNCTION BLOCK ASSEMBLY)

OK

4.CHECK BATTERY VOLTAGE SENSOR (VIB VOLTAGE)

NG

4.CHECK BATTERY VOLTAGE SENSOR (VIB VOLTAGE)

OK

5.CHECK BATTERY VOLTAGE SENSOR (GIB - GND)

NG

7.CHECK BATTERY VOLTAGE SENSOR (VIB VOLTAGE)
5.CHECK BATTERY VOLTAGE SENSOR (GIB - GND)

OK

6.CHECK HYBRID VEHICLE CONTROL ECU (HYBRID BATTERY CURRENT)

NG

REPLACE HV BATTERY JUNCTION BLOCK ASSEMBLY

6.CHECK HYBRID VEHICLE CONTROL ECU (HYBRID BATTERY CURRENT)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).

NOTICE:

During the inspection, make sure to only turn the power switch on (IG). Do not turn the power switch on (READY).



c.

Enter the following menus: Powertrain / Hybrid Control / Data List / Hybrid Battery Current, Hybrid Battery Current for Hybrid Battery Control.

Powertrain > Hybrid Control > Data List
Tester Display
Hybrid/EV Battery Current
Hybrid/EV Battery Current for Hybrid/EV Battery Control
50003 397 228,318

d.

With the power switch on (IG), monitor Data List item "Hybrid Battery Current" and "Hybrid Battery Current for Hybrid Battery Control" for 1 minute.


Result:
Result Proceed to
The value of Data List item "Hybrid Battery Current" and "Hybrid Battery Current for Hybrid Battery Control" is -0.5 A or less or 0.5 A or more. A
Other than above B


e.

Turn the power switch off.



A

B

7.CHECK BATTERY VOLTAGE SENSOR (VIB VOLTAGE)

OK

REPLACE HV BATTERY JUNCTION BLOCK ASSEMBLY

NG