Home › Engine / Hybrid System › 2ZR-FXE (HYBRID / BATTERY CONTROL) › HV BATTERY (for NICKEL METAL HYDRIDE BATTERY) › 2019.09–2020.08
RM32K0E _51 Engine / Hybrid System _083958 2ZR-FXE HYBRID / BATTERY CONTROL _0404378 HV BATTERY(for NICKEL METAL HYDRIDE BATTERY) N

2ZR-FXE HYBRID / BATTERY CONTROL  HV BATTERY(for NICKEL METAL HYDRIDE BATTERY)  CHARGING  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced when charging the HV battery are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Toyota parking assist-sensor system*1
Parking support brake system*1
Simple intelligent parking assist system*1
Pre-collision system
Memorize steering angle neutral point Panoramic view monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)

CAUTION:
·
A340386

This vehicle has contains high voltage circuits standardized with orange colored wiring and connectors, so follow the instructions in this manual to perform the procedures correctly.

Click hereEngine / Hybrid System>2ZR-FXE (HYBRID / BATTERY CONTROL)>HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY)>PRECAUTION

·

If the correct procedures are not followed according to the instructions in this manual, there is a danger of electric shock from the high voltage circuits.

·
A340358

Be sure to wear insulating gloves when working on high voltage wiring or components.

·

If work is performed without wearing insulating gloves, there is a danger of electric shock.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.INSPECT AUXILIARY BATTERY VOLTAGE

a.

Measure the auxiliary battery voltage.

Standard Voltage:

Approximately 11 V or more


HINT:
·

The horn should sound clearly.

·

If the voltage is 10 V or less, either charge the auxiliary battery (charging usually takes about 1 hour), or replace it with an auxiliary battery that is already charged.




Hide 3. PREPARATION FOR HV BATTERY CHARGING

CAUTION:
·

The hybrid system has high-voltage circuits. Accidents, such as electric shock, or electric leaks may result if the hybrid system is not operated in a correct manner. Make sure to follow the correct procedure.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Wear insulated gloves.



HINT:
·

Removing the service plug grip interrupts the high voltage circuit.

·

High voltage wiring connectors are orange.



a.

Check the charge level of the HV battery.

i.

If the hybrid system fails to start and "Traction battery needs to be protected. Shift into P to restart." or "Traction battery needs to be protected. Refrain from the use of N position." is displayed on the multi-information display, the HV battery may be discharged.


ii.

Confirm if the engine starts. If the engine starts, leave it idling with the shift lever in P until the engine stops (self charge has completed).

If the engine cannot start, charge the HV battery.

HINT:
·

Before performing external charging, always use the GTS to perform troubleshooting.

·

Charging time using the THS charger is 10 minutes per charge cycle. The charging time when using a THS charger is a short charging time (when the HV battery temperature is 25°C (77°F), 10 minutes may be sufficient, if the HV battery temperature is 0°C (32°F), then three 10 minute charge cycles may be required) for putting the engine in a condition where it can be started (the system can enter the READY-on state). (The THS charger will automatically stop 10 minutes after charging starts.)







d.

Remove the bench type rear seat cushion assembly.

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY>REMOVAL


e.

Remove the rear seat cushion lock hook.

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY>REMOVAL


f.

Remove the rear door scuff plate LH.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


g.

Remove the rear under side cover LH.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


h.

Remove the rear door scuff plate RH.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


i.

Remove the rear under side cover RH.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL






n.

Connect the THS charger in the order shown in the illustration.

A391975C01
1.469,1.833 1.802,1.833 true 4.667,0.583 4.833,0.583 4.833,0.583 5.146,1.563 true 6.24,1.542 6.24,1.375 6.24,1.375 5.99,1.208 true 3.885,2.083 3.885,1.917 3.885,1.917 4.135,1.833 true 0.917,6 1.094,6 1.094,6 1.75,4.917 true 1.833,6.25 2,6.25 2,6.25 2.677,4.844 true 6.25,5.25 6.083,5.25 6.083,5.25 4.833,4.583 true 4.979,5.917 6.167,5.917 true 4.885,6.25 5.25,6.917 5.25,6.917 5.417,6.917 true 5.896,0.833 6.229,0.833 true 4.333,6.917 4.333,6.75 4.333,6.75 4.583,6.448 true 3.042,7.365 3.375,7.365 false 3.219,7.823 3.552,7.823 false 5.938,7.417 6.271,7.417 false 0.792,1.708 1.438,1.896 0.646,0.188 10 true 1 SST *c 4.021,0.479 4.625,0.646 0.604,0.167 10 true 3 SST *a 5.948,1.583 6.563,1.813 0.615,0.229 10 true 2 SST *c 3.635,2.125 4.271,2.323 0.635,0.198 10 false 5 SST *b 6.25,5.802 6.885,6 0.635,0.198 10 false 6 SST *b 5.5,6.802 6.135,7 0.635,0.198 10 false 7 SST *c 4.073,6.958 4.708,7.156 0.635,0.198 10 false 4 SST *a 6.344,7.292 6.979,7.49 0.635,0.198 10 false SST *f 2.615,7.719 3.25,7.917 0.635,0.198 10 false 8 SST *d 6.281,0.708 6.542,0.906 0.26,0.198 10 true *4 1.625,6.146 1.885,6.344 0.26,0.198 10 false *2 0.708,5.896 0.969,6.094 0.26,0.198 10 false *3 2.844,7.25 3.104,7.448 0.26,0.198 10 false *e 6.313,5.146 6.573,5.344 0.26,0.198 10 false *1
*1 HV Battery *2 HV Floor Under Wire
*3 Inverter with Converter Assembly *4 No. 1 HV Battery Cover Panel RH
*a EV Bonding Cable (Green Cable) *b Low Voltage Cable
*c High Voltage Cable *d Power Input Plug
*e Grounded AC 100 to 240 V Receptacle *f THS Charger


NOTICE:
·

Make sure to connect the EV bonding cable first to prevent electrical shock.

·

Connect all of the THS charger cables in the order shown in the illustration to prevent electrical shock.




o.
A378153N01
1.125,1.729 1.448,1.729 true 0.781,1.656 1.115,1.823 0.333,0.167 10 true SST

Connect the 2 SST (high voltage cable) connectors to the HV battery junction block assembly.

SST
09882-10090  


p.
A378157N01
2.594,1.469 2.823,1.469 true 2.844,1.396 3.24,1.604 0.396,0.208 10 true SST

Temporarily install the No. 1 HV battery cover panel RH with the 2 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)

NOTICE:

Be careful not to pinch SST (high voltage cable).



q.

Connect the SST (high voltage cable) terminal to the position shown in the illustration with the nut.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


r.
A378161N01
1.188,1.5 1.406,1.5 1.406,1.5 1.552,1.708 true 0.792,1.417 1.208,1.604 0.417,0.188 10 true SST

Connect SST (EV bonding cable (green cable)) to the position shown in the illustration with the nut.

SST
09882-10070  

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


s.
A208147E03
0.906,1.76 1.542,1.76 true 2.365,1.458 2.365,1.802 true 0.604,1.688 1.115,2.031 0.51,0.344 10 false SST 2.25,1.844 2.729,2.135 0.479,0.292 10 false SST

Connect SST (EV bonding cable (green cable)) to SST (THS charger).

SST
09880-10021  (09881-10041)


t.
A378163N01
0.49,1.656 1.073,1.656 true 1.094,1.573 1.479,1.771 0.385,0.198 10 true SST

Connect SST (low voltage cable) to the position shown in the illustration with the bolt.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


u.
A305318C01
1.365,0.906 1.104,0.427 1.104,0.427 0.729,0.427 false 2.844,2.563 2.844,1.813 false 2.771,0.458 3.375,0.917 0.604,0.458 10 true 1 SST *a 0.167,2.375 0.75,2.833 0.583,0.458 10 true 2 SST *b 0.438,0.333 0.927,0.635 0.49,0.302 10 false SST 2.74,2.615 3.292,3.042 0.552,0.427 10 false SST
*a Low Voltage Cable
*b High Voltage Cable


Connect SST (low voltage cable) and SST (high voltage cable) to SST (THS charger) in the order shown in the illustration.



w.

Connect the cable to the negative (-) auxiliary battery terminal.

Click hereGeneral>MAINTENANCE>2ZR-FXE AUXILIARY BATTERY>INSTALLATION


x.

Connect SST (power input plug) of SST (THS charger) to a grounded AC 100 to 240 V receptacle.

SST
09881-10050  09881-10110  09881-10081  09881-10090  09881-10100  09881-10130  

NOTICE:

Always use an AC 100 to 240 V receptacle with a properly functioning ground. The ground is designed to reduce the chance of electric shock if a malfunction occurs. Do not use the charger if any of the pins on its plug have been damaged or removed.



Hide 4. HV BATTERY CHARGING

a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Active Test / Hybrid Battery Charge

Powertrain > Hybrid Control > Active Test
Tester Display
Hybrid Battery Charge
50004 397 42001
HINT:
·

While performing the "Battery Charge" Active Test, check the Data List items "System Main Relay Status - SMRB" and "System Main Relay Status - SMRG".

·

If the values of the Data List items are not as specified in the table below, turn the GTS and the power switch off and then perform the HV battery charging procedure again.



"System Main Relay Status - SMRB" and "System Main Relay Status - SMRG" in Data List during "Battery Charge" Active Test:
Step Active Test
"Battery Charge"
THS charger START
Switch
Data List
"System Main Relay Status - SMRB"
Data List
"System Main Relay Status - SMRG"
1 OFF OFF OFF OFF
2 OFF → ON OFF OFF → ON OFF → ON
3 ON OFF → ON ON ON



d.

Make sure that the EMERGENCY STOP switch is in the reset condition (the switch is turned clockwise and released).


e.

Make sure that the BREAKER is in the ON position.


f.
A208150

Turn the THS charger MAIN switch on.

HINT:

The MAIN indicator will illuminate (green).



g.

Press the START switch.

A208151

HINT:
·

When the START switch is turned on, the INITIAL CHECK indicator illuminates and an initial check starts. When the initial check completes successfully, the INITIAL CHECK indicator turns off, the CHARGING indicator illuminates and charging will start at the same time.

·

While the INITIAL CHECK indicator is illuminated, the insulation, 400 V output, emergency stop switch, connector connections and ground connection are inspected.




h.

Repeat the charge cycle 3 times. When the last cycle has finished, turn the THS charger MAIN switch off.

HINT:
·

Charging time using the THS charger is 10 minutes per charge cycle. The charging time when using a THS charger is a short charging time (when the battery temperature is 25°C (77°F), 10 minutes may be sufficient, if the battery temperature is 0°C (32°F), then three 10 minute charge cycles may be required) for putting the engine in a condition where it can be started (the system can enter the READY-on state). (The THS charger will automatically stop 10 minutes after charging starts.)

·

There is very little chance of overcharging the HV battery during the second or third charging cycle. The SOC will not likely increase beyond the upper limit because it was low enough to prevent the engine from starting. Even if the SOC was to increase enough to exceed the limit, the hybrid vehicle control ECU will stop the Active Test to prevent overcharging.

·

Cranking the engine once causes the SOC to drop approximately 1%.

·

Charging the HV battery once (10 minutes) using the THS charger restores the SOC approximately 2%.




i.

Turn the power switch off.


j.

Remove the THS charger and connect the HV floor under wire (for HV Battery).

NOTICE:

Make sure to disconnect the EV bonding cable last.


i.

Disconnect SST (power inlet plug) of SST (THS charger) from the grounded AC 100 to 240 V receptacle.


ii.

Disconnect the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>MAINTENANCE>2ZR-FXE AUXILIARY BATTERY>REMOVAL



iv.
A305317C04
1.198,0.948 0.969,0.406 0.969,0.406 0.74,0.406 false 2.771,0.469 3.385,0.781 0.615,0.313 10 true 2 SST *a 0.26,2.396 0.854,2.74 0.594,0.344 10 true 1 SST *b 0.417,0.344 0.927,0.698 0.51,0.354 10 false SST
*a Low Voltage Cable
*b High Voltage Cable


Disconnect SST (high voltage cable) and SST (low voltage cable) from SST (THS charger) in the order shown in the illustration.


v.
A378163N01
0.49,1.656 1.073,1.656 true 1.094,1.573 1.479,1.771 0.385,0.198 10 true SST

Remove the bolt and disconnect SST (low voltage cable).


vi.
A208147E03
0.906,1.76 1.542,1.76 true 2.365,1.458 2.365,1.802 true 0.604,1.688 1.115,2.031 0.51,0.344 10 false SST 2.25,1.844 2.729,2.135 0.479,0.292 10 false SST

Disconnect SST (EV bonding cable (green cable)) from SST (THS charger).


vii.
A378161N01
1.188,1.5 1.406,1.5 1.406,1.5 1.552,1.708 true 0.792,1.417 1.208,1.604 0.417,0.188 10 true SST

Remove the nut and disconnect SST (EV bonding cable (green cable)).


viii.
A378157N01
2.594,1.469 2.823,1.469 true 2.844,1.396 3.24,1.604 0.396,0.208 10 true SST

Remove the nut and disconnect the SST (high voltage cable) terminal.


ix.

Remove the 2 bolts and No. 1 HV battery cover panel RH.


x.
A378153N01
1.125,1.729 1.448,1.729 true 0.781,1.656 1.115,1.823 0.333,0.167 10 true SST

Disconnect the 2 SST (high voltage cable) connectors from the HV battery junction block assembly.






k.

Turn the power switch on (READY) and check if the engine starts.

HINT:

If the engine does not start, perform the HV battery charging operation again.





n.

Install the rear under side cover LH.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION


o.

Install the rear door scuff plate LH.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION


p.

Install the rear under side cover RH.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION


q.

Install the rear door scuff plate RH.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION


r.

Install the rear seat cushion lock hook.

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY>INSTALLATION


s.

Install the bench type rear seat cushion assembly.

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY>INSTALLATION



Hide 5. CHECK HV BATTERY AFTER HV BATTERY CHARGE


b.

Perform the self-charging operation.

i.

Start the engine and leave it idling with the shift lever in P until the engine stops.

HINT:

When the engine stops idling, this indicates that self-charging is complete. Perform any initialization procedures required after the negative (-) terminal of the auxiliary battery is disconnected and reconnected.