Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SIDE AIRBAG SENSOR (for Front Door) › from 2020.08
RM32K0E _58 Vehicle Interior _062267 SUPPLEMENTAL RESTRAINT SYSTEMS _0303879 SIDE AIRBAG SENSOR(for Front Door) A

SUPPLEMENTAL RESTRAINT SYSTEMS  SIDE AIRBAG SENSOR(for Front Door)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The following procedure is for LHD vehicles.

·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 89835 1.INSTALL DOOR SIDE AIRBAG SENSOR

a.

Check that the power switch off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
B422343

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Connect the connector to the door side airbag sensor.

B312074C37
2.24,0.823 2.552,0.552 true 2.417,1.01 3,0.792 true 3.052,0.677 3.26,0.885 0.208,0.208 10 false *a 5.938,3.365 6.25,3.521 0.313,0.156 10 false *b 2.625,0.406 2.958,0.635 0.333,0.229 10 false (A)
*a White Housing Lock *b Connection is completed


NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.


HINT:
·

Be sure to connect the connector until it is locked (when locking, make sure that a click sound can be heard).

·

When the connector is locked, the white housing lock will slide. Do not hold the white housing lock or the part (A) as it may result in an insecure connection.




d.

Before connecting the connector, check that the position of the white housing lock is as shown in the illustration.

B296255C05
4.76,1.833 5.031,2.104 0.271,0.271 10 false *b 1.396,1.833 1.677,2.115 0.281,0.281 10 false *b 4.76,0.573 5.031,0.875 0.271,0.302 10 false *a 1.396,0.573 1.677,0.865 0.281,0.292 10 false *a
*a Incorrect *b Correct



e.
B458400

Engage the claw to install the door side airbag sensor with the nut.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)

NOTICE:
·

If the door side airbag sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.

·

When installing the door side airbag sensor, make sure that the SRS wiring does not interfere with or is not pinched between other parts.

·

Make sure that the door side airbag sensor claw is securely inserted into the door hole.

·

Keep the stud bolt and waterproof rubber seal free of foreign matter.




f.

Check that there is no looseness in the installed parts of the door side airbag sensor.


Hide 67832 2.INSTALL FRONT DOOR SERVICE HOLE COVER

Hide 67602 3.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY

Hide 74232 4.INSTALL MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)

Hide 74231 5.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)

Hide 69284C 6.INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG

Hide 7.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 8. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART