Home › Engine / Hybrid System › 8NR-FTS (ENGINE CONTROL) › SFI SYSTEM
RM32H0E _51 Engine / Hybrid System _059353 8NR-FTS ENGINE CONTROL _0290422 SFI SYSTEM C

8NR-FTS ENGINE CONTROL  SFI SYSTEM  P001107  Camshaft Position "A" - Timing Over-Advanced or System Performance Bank 1 Mechanical Failure  


DESCRIPTION

Refer to DTC P001013.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>P001013

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P001107 Camshaft Position "A" - Timing Over-Advanced or System Performance Bank 1 Mechanical Failure 10° CA or greater camshaft timing gear assembly run-out maintained for 3 seconds or longer for 2 times (1 trip detection logic).
·

Cam timing oil control solenoid assembly (for intake camshaft)

·

Camshaft timing gear bolt (intake camshaft timing oil control valve)

·

Camshaft timing gear assembly

·

ECM


Comes on DTC stored SAE Code:
P0011

MONITOR DESCRIPTION

During idling, the camshaft timing gear is locked at the center of the variable valve timing operating range by the two lock pins. The camshaft timing gear assembly run-out increases if one lock pin is stuck in the retracted position. In this case, the ECM illuminates the MIL and stores this DTC.

MONITOR STRATEGY

Required Sensors/Components (Main) Cam timing oil control solenoid assembly (for intake camshaft)
Camshaft timing gear bolt (intake camshaft timing oil control valve)
Camshaft timing gear assembly
Required Sensors/Components (Related) Crankshaft position sensor
Camshaft position sensor
Engine coolant temperature sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Start the engine.

9.

Wait 20 seconds or more.

10.

Enter the following menus: Powertrain / Engine / Trouble Codes.

11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

13.

Input the DTC: P001107.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM SIMULATION TEST (CHECK FOR ABNORMAL NOISE)
a.

Start the engine.


b.

Check for abnormal noise (rattling sounds) from the camshaft timing gear assembly with the engine idling.

Result:
Result Proceed to
Abnormal noise (rattling sound) from the camshaft timing gear assembly is heard. A
Abnormal noise (rattling sound) from the camshaft timing gear assembly is not heard. B


HINT:
·

As the engine speed increases, the camshaft timing gear assembly lock pins will release and the abnormal noise (rattling sound) will disappear.

·

Perform "Inspection After Repair" after replacing the camshaft timing gear assembly.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION





A

REPLACE CAMSHAFT TIMING GEAR BOLT (INTAKE CAMSHAFT TIMING OIL CONTROL VALVE) AND CAMSHAFT TIMING GEAR ASSEMBLY

CAMSHAFT TIMING GEAR BOLT (INTAKE CAMSHAFT TIMING OIL CONTROL VALVE): Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>CAMSHAFT OIL CONTROL VALVE (for Intake Side)>REMOVAL

CAMSHAFT TIMING GEAR ASSEMBLY: Click hereEngine / Hybrid System>8NR-FTS (ENGINE MECHANICAL)>CAMSHAFT>REMOVAL


B

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INTAKE VVT OCV DUTY RATIO BANK 1)
2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INTAKE VVT OCV DUTY RATIO BANK 1)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Active Test / Control the Intake VVT OCV Duty Ratio Bank 1 / Data List / All Data / Intake VVT Change Angle Bank 1.

Powertrain > Engine > Active Test
Active Test Display
Control the Intake VVT OCV Duty Ratio Bank 1
Data List Display
Intake VVT Change Angle Bank 1
50004 372 4 397

e.

Read the Data List while performing the Active Test with the engine idling.

OK:
GTS Operation Data List (Intake VVT Change Angle Bank 1)
-100% to 100% Varies by 70 DegFR or more



Result:
Proceed to
OK
NG



OK

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P001107)

NG

4.INSPECT CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR INTAKE CAMSHAFT)
3.CHECK WHETHER DTC OUTPUT RECURS (DTC P001107)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Start the engine.


g.

Turn the GTS on.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 20

j.

Input the DTC: P001107.


k.

Check the DTC judgment result.

Result:
Result Proceed to
NORMAL
(DTCs are not output)
A
ABNORMAL
(DTC P001107 is output)
B




A

B

4.INSPECT CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR INTAKE CAMSHAFT)
4.INSPECT CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR INTAKE CAMSHAFT)
a.

Inspect the cam timing oil control solenoid assembly (for intake camshaft).

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>CAMSHAFT OIL CONTROL SOLENOID>INSPECTION


Result:
Proceed to
OK
NG



OK

5.INSPECT CAMSHAFT TIMING GEAR BOLT (INTAKE CAMSHAFT TIMING OIL CONTROL VALVE)

NG

6.REPLACE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR INTAKE CAMSHAFT)
5.INSPECT CAMSHAFT TIMING GEAR BOLT (INTAKE CAMSHAFT TIMING OIL CONTROL VALVE)
a.

Inspect the camshaft timing gear bolt (intake camshaft timing oil control valve).

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>CAMSHAFT OIL CONTROL VALVE (for Intake Side)>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

10.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY

NG

8.REPLACE CAMSHAFT TIMING GEAR BOLT (INTAKE CAMSHAFT TIMING OIL CONTROL VALVE)
6.REPLACE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR INTAKE CAMSHAFT)
a.

Replace the cam timing oil control solenoid assembly (for intake camshaft).

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>CAMSHAFT OIL CONTROL SOLENOID>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.INSPECT CAMSHAFT TIMING GEAR BOLT (INTAKE CAMSHAFT TIMING OIL CONTROL VALVE)
7.INSPECT CAMSHAFT TIMING GEAR BOLT (INTAKE CAMSHAFT TIMING OIL CONTROL VALVE)
a.

Inspect the camshaft timing gear bolt (intake camshaft timing oil control valve).

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>CAMSHAFT OIL CONTROL VALVE (for Intake Side)>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

9.PERFORM ACTIVE TEST USING GTS (CONTROL THE INTAKE VVT OCV DUTY RATIO BANK 1)

NG

8.REPLACE CAMSHAFT TIMING GEAR BOLT (INTAKE CAMSHAFT TIMING OIL CONTROL VALVE)
8.REPLACE CAMSHAFT TIMING GEAR BOLT (INTAKE CAMSHAFT TIMING OIL CONTROL VALVE)
a.

Replace the camshaft timing gear bolt (intake camshaft timing oil control valve).

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>CAMSHAFT OIL CONTROL VALVE (for Intake Side)>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.PERFORM ACTIVE TEST USING GTS (CONTROL THE INTAKE VVT OCV DUTY RATIO BANK 1)
9.PERFORM ACTIVE TEST USING GTS (CONTROL THE INTAKE VVT OCV DUTY RATIO BANK 1)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Active Test / Control the Intake VVT OCV Duty Ratio Bank 1 / Data List / All Data / Intake VVT Change Angle Bank 1.

Powertrain > Engine > Active Test
Active Test Display
Control the Intake VVT OCV Duty Ratio Bank 1
Data List Display
Intake VVT Change Angle Bank 1
50004 372 4 397

e.

Read the Data List while performing the Active Test with the engine idling.

OK:
GTS Operation Data List (Intake VVT Change Angle Bank 1)
-100% to 100% Varies by 70 DegFR or more



Result:
Proceed to
OK
NG



OK

END

NG

10.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY
10.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY
a.

Replace the camshaft timing gear assembly.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE MECHANICAL)>CAMSHAFT>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the camshaft timing gear assembly.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

11.CHECK WHETHER DTC OUTPUT RECURS (DTC P001107)
11.CHECK WHETHER DTC OUTPUT RECURS (DTC P001107)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Start the engine.


g.

Turn the GTS on.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 20

j.

Input the DTC: P001107.


k.

Check the DTC judgment result.

Result:
Result Proceed to
NORMAL
(DTCs are not output)
A
ABNORMAL
(DTC P001107 is output)
B




A

END

B