Home › Engine / Hybrid System › 8NR-FTS (ENGINE MECHANICAL) › ENGINE › 2016.10–2019.09
RM32H0E _51 Engine / Hybrid System _059498 8NR-FTS ENGINE MECHANICAL _0291510 ENGINE G

8NR-FTS ENGINE MECHANICAL  ENGINE  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

CAUTION:
·
A345137

When working near the engine room while the engine has started or the power source mode is ignition switch to ON (IG), do not touch the fan and generator V belt or rotating components such as the fan, etc.

·

Touching the fan and generator V belt or rotating components such as the fan, etc. could result in your hand or clothing getting caught and pulled in.



PROCEDURE

Hide 17801 5.INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 16620 7.INSPECT V-RIBBED BELT TENSIONER ASSEMBLY

a.

Remove the fan and generator V belt.

Click hereGeneral>MAINTENANCE>8NR-FTS DRIVE BELT>REMOVAL


b.

Turn the V-ribbed belt tensioner assembly clockwise and counterclockwise and check that it turns smoothly and does not catch.

HINT:

If the V-ribbed belt tensioner assembly does not turn smoothly or catches, replace the V-ribbed belt tensioner assembly.



c.

Install the fan and generator V belt.

Click hereGeneral>MAINTENANCE>8NR-FTS DRIVE BELT>INSTALLATION


Hide 13750 8.INSPECT VALVE LASH ADJUSTER ASSEMBLY NOISE

a.

Rev up the engine several times. Check that the engine does not emit unusual noises.


b.

If unusual noises occur, warm up the engine and idle it for 30 minutes or more, then perform the inspection.

HINT:

If any defects or problems are found during the inspection, perform valve lash adjuster assembly inspection.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE MECHANICAL)>ENGINE UNIT>INSPECTION



Hide 9.INSPECT IGNITION TIMING

a.

Warm up and stop the engine.


b.

When using the GTS:

i.

Connect the GTS to the DLC3.


ii.

Start the engine and run it at idle.


iii.

Turn the GTS on.


iv.

Enter the following menus: Powertrain / Engine and ECT / Data List / IGN Advance.

Powertrain > Engine and ECT > Data List
Tester Display
IGN Advance
50003 234 29
Standard Ignition Timing:

-5 to 25° BTDC at idle


NOTICE:
·

Check the ignition timing with the cooling fans off.

·

Turn off all electrical systems and the A/C (w/ Air conditioning system).

·

When checking the ignition timing, the transaxle should be in neutral or park.




v.

Enter the following menus: Powertrain / Engine / Active Test / Connect the TC and TE1 / ON.

Powertrain > Engine > Active Test
Active Test Display
Connect the TC and TE1
Data List Display
IGN Advance
50004 234 13 29

vi.

Monitor IGN Advance of the Data List.

Standard Ignition Timing:

8 to 12° BTDC at idle



vii.

Enter the following menus: Powertrain / Engine / Active Test / Connect the TC and TE1 / OFF.


viii.

Check that the ignition timing advances immediately when the engine speed is increased.



c.

When not using the GTS:

i.
A206183C10
1.771,1.479 2.083,1.917 2.083,1.917 2.167,1.917 true 1.604,0.927 1.333,0.396 1.333,0.396 1.219,0.396 true 0.073,0.083 0.438,0.385 0.365,0.302 10 *a 2.208,1.833 2.521,2.031 0.313,0.198 10 TC 1,0.313 1.396,0.552 0.396,0.24 10 CG
*a DLC3


Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  

NOTICE:
·

Confirm the terminal numbers before connecting them. Connecting the wrong terminals may damage electrical components.

·

Check the ignition timing with the cooling fans off.

·

Turn off all electrical systems and the A/C (w/ Air conditioning system).

·

When checking the ignition timing, the transaxle should be in neutral or park.




ii.
A392303

Connect the clip of a timing light to the ignition coil wire for the No. 1 cylinder.

NOTICE:

Use a timing light that detects primary signals.



iii.

Start the engine and run it at idle.


iv.
A351479C01
1.49,1.406 1.219,1.802 1.219,1.802 1.615,1.51 true 1.844,1.333 2.531,1.667 true 1.354,1.198 1.167,0.771 true 1.125,1.844 1.438,2.042 0.313,0.198 10 true *a 2.583,1.646 2.896,1.844 0.313,0.198 10 true *b 0.979,0.542 1.292,0.74 0.313,0.198 10 true *c
*a TDC
*b 10° BTDC
*c Cutout


Check the ignition timing at idle.

Standard Ignition Timing:

8 to 12° BTDC at idle


HINT:

If the cutout of the crankshaft pulley assembly is at a position between the protrusion (10° BTDC) of the timing chain cover assembly and TDC, the ignition timing meets the standard.



v.

Disconnect terminals 13 (TC) and 4 (CG) of the DLC3.


vi.

Check the ignition timing at idle.

Standard Ignition Timing:

-5 to 25° BTDC at idle



vii.

Confirm that the ignition timing advances immediately when the engine speed is increased.


viii.

Disconnect the clip of the timing light from the ignition coil wire for the No. 1 cylinder.



Hide 10.INSPECT ENGINE IDLE SPEED

a.

Warm up and stop the engine.


b.

When using the GTS:

i.

Connect the GTS to the DLC3.


ii.

Start the engine and run it at idle.


iii.

Turn the GTS on.


iv.

Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.

Powertrain > Engine and ECT > Data List
Tester Display
Engine Speed
50003 234 9

v.

Read the value displayed on the tester.

Standard Idle Speed:
for Manual Transaxle:

600 to 700 rpm

for CVT:

680 to 780 rpm


NOTICE:
·

Check the engine idle speed with the cooling fans off.

·

Turn off all electrical systems and the A/C (w/ Air conditioning system).

·

When checking the engine idle speed, the transaxle should be in neutral or park.





c.

When not using the GTS:

i.
A206183C91
0.656,1.479 1,1.479 false 0.083,0.063 0.281,0.26 0.198,0.198 10 false *a 0.354,1.417 0.979,1.708 0.625,0.292 10 false TAC
*a DLC3


Using SST, connect a tachometer probe to terminal 9 (TAC) of the DLC3.

SST
09843-18030  

NOTICE:

Be sure to connect the tachometer probe to the correct terminal. Connecting the wrong terminals can cause damage to electrical components.



ii.

Start the engine and run it at idle.


iii.

Inspect the engine idle speed.

Standard Idle Speed:
for Manual Transaxle:

600 to 700 rpm

for CVT:

680 to 780 rpm


NOTICE:
·

Check the engine idle speed with the cooling fans off.

·

Turn off all electrical systems and the A/C (w/ Air conditioning system).

·

When checking the engine idle speed, the transaxle should be in neutral or park.




iv.

Disconnect the tachometer probe from terminal 9 (TAC) of the DLC3.



Hide 11.INSPECT COMPRESSION

NOTICE:

Keep the spark plug holes free of foreign matter when measuring the compression pressure.


a.

Warm up and stop the engine.



c.

d.

Remove the 4 spark plugs.

Click hereGeneral>MAINTENANCE>8NR-FTS SPARK PLUG>REMOVAL


e.
A392304

Disconnect the engine wire connector as shown in the illustration.

NOTICE:

Disable fuel injection in order to prevent catalyst damage due to unburned gasoline.



f.

Check the cylinder compression pressure.

i.
A392305

Insert a compression gauge into the spark plug hole.


ii.

Fully open the throttle.


iii.

While cranking the engine, measure the compression pressure.

Standard Compression Pressure:

1080 kPa (11.0 kgf/cm2, 157 psi)


Minimum Compression Pressure:

880 kPa (9.0 kgf/cm2, 128 psi)


Pressure Difference between Each Cylinder:

100 kPa (1.0 kgf/cm2, 15 psi) or less


NOTICE:
·

Always use a fully charged battery to obtain an engine speed of 250 rpm or more.

·

Inspect all cylinders in the same way.

·

Measure the compression pressure as quickly as possible.




iv.

If the cylinder compression pressure is low, pour a small amount of engine oil into the cylinder through the spark plug hole and inspect it again.

HINT:
·

If adding oil increases the compression pressure, the piston rings and/or cylinder bore may be worn or damaged.

·

If the compression pressure stays low, a valve may be stuck or seated improperly, or there may be leaks in the cylinder head gasket.





g.

Connect the engine wire connector.


h.

Install the 4 spark plugs.

Click hereGeneral>MAINTENANCE>8NR-FTS SPARK PLUG>INSTALLATION



j.

Clear the DTCs.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR

NOTICE:

After the inspection, clear the DTCs, check for DTCs again and make sure the normal system code is output.



Hide 12.INSPECT CO/HC

HINT:

This check determines whether or not the idle CO/HC complies with regulations.


a.

Start the engine.


b.

Run the engine at 2500 rpm for approximately 180 seconds.


c.

Insert a CO/HC meter testing probe at least 40 cm (1.31 ft.) into the tailpipe during idle.


d.

Immediately check the CO/HC concentration during idle and when the engine is running at 2500 rpm.

HINT:

When performing a 2 mode (with the engine idling/running at 2500 rpm) test, the measurement procedures are determined by applicable local regulations.

If the CO/HC concentration does not comply with the regulations, perform troubleshooting in the order given below.



ii.

See the following table for possible causes, then inspect the applicable parts and repair them if necessary.

CO HC Problem Cause
Normal High Rough idle
1.

Faulty ignition:

-

Incorrect valve timing

-

Fouled, shorted or improperly gapped spark plugs


2.

Incorrect valve clearance (valve lash adjuster assembly)

3.

Leaks in intake or exhaust valves

4.

Leaks in cylinders


Low High Rough idle (Fluctuating HC reading)
1.

Vacuum leaks:

-

PCV hoses

-

Intake manifold

-

Throttle body with motor assembly


2.

Lean mixture causing misfire


High High Rough idle (Black smoke from exhaust)
1.

Restricted air cleaner filter element sub-assembly

2.

Plugged PCV valve

3.

Faulty SFI systems:

-

Fuel pressure regulator assembly

-

Engine coolant temperature sensor

-

Mass air flow meter

-

ECM

-

Fuel injector assemblies

-

Throttle position sensor (built into throttle body with motor assembly)