Home › Drivetrain › K114 (MULTIDRIVE / CVT) › OIL COOLER
RM32H0E _52 Drivetrain _059616 K114 MULTIDRIVE / CVT _0292454 OIL COOLER A

K114 MULTIDRIVE / CVT  OIL COOLER  INSTALLATION  


PROCEDURE

Hide 32913F 1.INSTALL TRANSMISSION OIL COOLER BRACKET

a.
C365139C02
2.531,0.479 3.156,0.656 0.625,0.177 10 true 1 (*a), 4 1.073,0.469 1.229,0.667 0.156,0.198 10 true 2 2.302,1.51 2.458,1.708 0.156,0.198 10 true 3
*a Temporarily Tighten


Install the transmission oil cooler bracket to the continuously variable transaxle assembly with the 3 bolts in the order shown in the illustration.

Torque:
13.5 N*m (138 kgf*cm, 10 ft.*lbf)


Hide 33493B 2.INSTALL OIL COOLER

a.
C365138C02
1.073,0.25 1.719,0.458 0.646,0.208 10 true 1 (*a), 3 1.281,1.823 1.438,2.021 0.156,0.198 10 true 2
*a Temporarily Tighten


Install the oil cooler to the transmission oil cooler bracket with the 2 bolts in the order shown in the illustration.

Torque:
13.5 N*m (138 kgf*cm, 10 ft.*lbf)


Hide 32943S 3.CONNECT NO. 1 TRANSMISSION OIL COOLER HOSE

a.

Connect the No. 1 transmission oil cooler hose to the oil cooler, and slide the clip to secure it.

NOTICE:
·

Align each paint mark on the No. 1 transmission oil cooler hose with each one on the oil cooler.

·

Fully insert the No. 1 transmission oil cooler hose to the 2nd rib on each oil cooler pipe.




Hide 32943U 4.CONNECT NO. 2 TRANSMISSION OIL COOLER HOSE

a.

Connect the No. 2 transmission oil cooler hose to the oil cooler, and slide the clip to secure it.

NOTICE:
·

Align each paint mark on the No. 2 transmission oil cooler hose with each one on the oil cooler.

·

Fully insert the No. 2 transmission oil cooler hose to the 2nd rib on each oil cooler pipe.




Hide 16267 5.CONNECT NO. 3 WATER BY-PASS HOSE

a.

Connect the No. 3 water by-pass hose to the oil cooler, and slide the clip to secure it.

NOTICE:
·

Align each paint mark on the No. 3 water by-pass hose with each one on the oil cooler.

·

Fully insert the No. 3 water by-pass hose to the 2nd rib on each oil cooler pipe.




Hide 16282 6.CONNECT NO. 5 WATER BY-PASS HOSE

a.

Connect the No. 5 water by-pass hose to the oil cooler, and slide the clip to secure it.

NOTICE:
·

Align each paint mark on the No. 5 water by-pass hose with each one on the oil cooler.

·

Fully insert the No. 5 water by-pass hose to the 2nd rib on each oil cooler pipe.




Hide 17701 7.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

Hide 17705 8.INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 17751 9.INSTALL NO. 1 AIR CLEANER INLET

Hide 53141F 10.INSTALL RADIATOR COVER

Hide 11.ADD ENGINE COOLANT

Hide 13.ADD CONTINUOUSLY VARIABLE TRANSAXLE FLUID

Hide 51444A 15.INSTALL REAR ENGINE UNDER COVER LH

Hide 51410 16.INSTALL NO. 1 ENGINE UNDER COVER