Home › Drivetrain › K313F (MULTIDRIVE / CVT) › FRONT DIFFERENTIAL OIL SEAL (for LH Side)
RM32H0E _52 Drivetrain _059618 K313F MULTIDRIVE / CVT _0292477 FRONT DIFFERENTIAL OIL SEAL(for LH Side) A

K313F MULTIDRIVE / CVT  FRONT DIFFERENTIAL OIL SEAL(for LH Side)  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the front drive shaft oil seal replacement are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Replacement of CVT fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)
Front wheel alignment adjustment Perform the following procedures in the order shown:
1.

Clear zero point calibration data and store system information

2.

Perform yaw rate and acceleration sensor zero point calibration and store system information


·

DTCs are stored

·

ABS warning light illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)

PROCEDURE

Hide 51441 1.REMOVE NO. 1 ENGINE UNDER COVER

Hide 51444A 2.REMOVE REAR ENGINE UNDER COVER LH

Hide 3.DRAIN CONTINUOUSLY VARIABLE TRANSAXLE FLUID

a.
C362025

Remove the refill plug and gasket from the rear transaxle case.


b.
C362026

Using a 6 mm hexagon socket wrench, remove the overflow plug and gasket from the transaxle oil (CVT) pan sub-assembly.


c.
C364033C01
2.365,0.656 2.583,0.844 true 2.198,0.51 2.51,0.708 0.313,0.198 10 false *1
*1 No. 1 Transmission Oil Filler Tube


Using a 6 mm hexagon socket wrench, remove the No. 1 transmission oil filler tube from the transaxle oil (CVT) pan sub-assembly, and drain the fluid.

HINT:

Removing the No. 1 transmission oil filler tube will drain all oil in the transaxle oil (CVT) pan sub-assembly.



d.

Using a 6 mm hexagon socket wrench, install the No. 1 transmission oil filler tube to the transaxle oil (CVT) pan sub-assembly.

Torque:
1.7 N*m (17 kgf*cm, 15 in.*lbf)


e.

Using a 6 mm hexagon socket wrench, temporarily install the overflow plug and gasket to the transaxle oil (CVT) pan sub-assembly.

HINT:

Reuse the old gasket as the overflow plug will be removed again to adjust the fluid level.



f.

Temporarily install the gasket and refill plug to the rear transaxle case.

HINT:

Reuse the old gasket as the refill plug will be removed again to adjust the fluid level.



Hide 4.REMOVE FRONT DRIVE SHAFT ASSEMBLY LH (for TMMT Made)

Hide 5.REMOVE FRONT DRIVE SHAFT ASSEMBLY LH (for TMC Made)

Hide 43420H 6.REMOVE FRONT DRIVE SHAFT OIL SEAL LH

a.
C160542N05
2.219,1.344 2.906,2.24 true 1.198,2.521 1.063,2.896 false 0.948,2.927 1.354,3.135 0.406,0.208 10 false SST 2.823,2.271 3.26,2.5 0.438,0.229 10 false SST

Using SST, remove the front drive shaft oil seal LH from the transaxle case.

SST
09308-00010  

NOTICE:

Do not damage the transaxle case.



Hide 43420H 7.INSTALL FRONT DRIVE SHAFT OIL SEAL LH

a.

Coat the lip of a new front drive shaft oil seal LH with MP grease.


b.
C269119C02
1.656,1.031 0.479,0.698 0.479,0.698 0.854,1.531 true 1.948,2.729 1.948,2.583 false 0.188,0.604 0.469,0.76 0.281,0.156 10 true SST 1.833,2.75 2.24,2.927 0.406,0.177 10 false SST 1.771,3 2.083,3.198 0.313,0.198 10 false *a
*a Depth


Using SST and a hammer, install the front drive shaft oil seal LH to the transaxle case.

SST
09387-00010  
09950-70010  (09951-07150)

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:
·

Be sure to install the front drive shaft oil seal LH in the correct direction.

·

Make sure to install the front drive shaft oil seal LH as specified, otherwise malfunctions such as a fluid leak will occur.

·

Do not damage the lip of the front drive shaft oil seal LH.




Hide 8.INSTALL FRONT DRIVE SHAFT ASSEMBLY LH (for TMMT Made)

Hide 9.INSTALL FRONT DRIVE SHAFT ASSEMBLY LH (for TMC Made)

Hide 10.ADD CONTINUOUSLY VARIABLE TRANSAXLE FLUID

Hide 11.INSPECT FOR FLUID LEAK

Hide 51444A 12.INSTALL REAR ENGINE UNDER COVER LH

Hide 51441 13.INSTALL NO. 1 ENGINE UNDER COVER