Home › Drivetrain › K114 (MULTIDRIVE / CVT) › FRONT DIFFERENTIAL OIL SEAL
RM32H0E _52 Drivetrain _059616 K114 MULTIDRIVE / CVT _0292460 FRONT DIFFERENTIAL OIL SEAL A

K114 MULTIDRIVE / CVT  FRONT DIFFERENTIAL OIL SEAL  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the front differential oil seal removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Replacement of CVT fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)

PROCEDURE

Hide 51441 1.REMOVE NO. 1 ENGINE UNDER COVER

Hide 51444A 2.REMOVE REAR ENGINE UNDER COVER LH

Hide 51443C 3.REMOVE REAR ENGINE UNDER COVER RH

Hide 4.DRAIN CONTINUOUSLY VARIABLE TRANSAXLE FLUID

a.
C362022

Remove the refill plug and gasket from the continuously variable transaxle assembly.


b.
C365125

Using a 10 mm hexagon socket wrench, remove the drain plug and gasket from the transaxle oil (CVT) pan sub-assembly, and drain the fluid.


c.

Install a new gasket and the drain plug to the transaxle oil (CVT) pan sub-assembly.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)


d.

Temporarily install the gasket and refill plug to the continuously variable transaxle assembly.

HINT:

Reuse the old gasket. The refill plug will be removed again to adjust the fluid level.



Hide 43457 6.REMOVE DRIVE SHAFT BEARING BRACKET

Hide 43420H 7.REMOVE FRONT DRIVE SHAFT OIL SEAL LH

C295669N01
0.854,2.5 0.844,2.198 0.844,2.198 1.458,1.417 true 2.146,3.073 2.333,3.073 2.333,3.073 2.333,2.875 false 0.76,2.563 1.198,2.813 0.438,0.25 10 false SST 1.875,3 2.333,3.198 0.458,0.198 10 false SST

a.

Using SST, remove the front drive shaft oil seal LH from the continuously variable transaxle assembly.

SST
09308-00010  

NOTICE:

Do not damage the continuously variable transaxle assembly.



Hide 43410M 8.REMOVE FRONT DRIVE SHAFT OIL SEAL RH

C297221N01
0.615,1.188 1.198,1.188 false 3.063,2.76 3.063,2.458 false 0.313,1.125 0.771,1.323 0.458,0.198 10 false SST 2.958,2.792 3.417,2.99 0.458,0.198 10 false SST

a.

Using SST, remove the front drive shaft oil seal RH from the continuously variable transaxle assembly.

SST
09308-00010  

NOTICE:

Do not damage the continuously variable transaxle assembly.



Hide 43420H 9.INSTALL FRONT DRIVE SHAFT OIL SEAL LH

a.

Apply MP grease to the lip of a new front drive shaft oil seal LH.


b.
C343204C01
1.458,1.385 0.896,0.448 0.896,0.448 2.042,0.885 true 2.104,2.896 2.417,3.094 0.313,0.198 10 false *a 0.531,0.344 0.99,0.542 0.458,0.198 10 true SST
*a -0.5 to 0.5 mm


Using SST and a hammer, install the front drive shaft oil seal LH to the continuously variable transaxle assembly.

SST
09316-10010  
09950-70010  (09951-07200)

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:
·

Be sure to install the front drive shaft oil seal LH in the correct direction.

·

Make sure to install the front drive shaft oil seal LH as specified, otherwise malfunctions such as a fluid leak will occur.

·

Do not damage the lip of the front drive shaft oil seal LH.




Hide 43410M 10.INSTALL FRONT DRIVE SHAFT OIL SEAL RH

a.

Apply MP grease to the lip of a new front drive shaft oil seal RH.


b.
C297223C02
0.448,0.344 0.917,0.344 0.917,0.344 2.063,0.656 true 1.26,1.344 0.906,0.344 false 2.76,2.781 2.76,2.615 false 0.156,0.26 0.615,0.458 0.458,0.198 10 false SST 2.667,2.802 3.125,3 0.458,0.198 10 false SST 2.802,2.958 3.115,3.115 0.313,0.156 10 false *a
*a -0.5 to 0.5 mm


Using SST and a hammer, install the front drive shaft oil seal RH to the continuously variable transaxle assembly.

SST
09316-10010  
09950-70010  (09951-07200)

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:
·

Be sure to install the front drive shaft oil seal RH in the correct direction.

·

Make sure to install the front drive shaft oil seal RH as specified, otherwise malfunctions such as a fluid leak will occur.

·

Do not damage the lip of the front drive shaft oil seal RH.




Hide 43457 11.INSTALL DRIVE SHAFT BEARING BRACKET

Hide 13.ADD CONTINUOUSLY VARIABLE TRANSAXLE FLUID

Hide 14.INSPECT FOR FLUID LEAK

Hide 51444A 15.INSTALL REAR ENGINE UNDER COVER LH

Hide 51443C 16.INSTALL REAR ENGINE UNDER COVER RH

Hide 51441 17.INSTALL NO. 1 ENGINE UNDER COVER