Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM32H0E _58 Vehicle Interior _060136 METER / GAUGE / DISPLAY _0294876 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Fuel Receiver Gauge Display Malfunction  


DESCRIPTION

OPERATION


The combination meter assembly uses the fuel injection volume signal from the ECM, fuel sender gauge assembly and No. 2 fuel sender gauge assembly*1 to detect the amount of fuel remaining in the fuel tank assembly. Each gauge assembly has a variable resistor whose resistance changes according to the amount of fuel remaining. The gauge assemblies receive voltage from the combination meter assembly and change the voltage based on the resistance that changes according to the amount of fuel remaining in the fuel tank assembly. The combination meter assembly receives a fuel injection volume signal from the ECM and detects the voltage between each variable resistor and each resistor in the combination meter assembly, and operates the fuel receiver gauge.

*1: for AWD



FUEL RECEIVER GAUGE READING


a.

During normal driving:

As the fuel level in the fuel tank assembly changes when driving on a hill or applying brakes, the fuel receiver gauge reading is updated according to the fuel injection volume during normal driving. However, as the fuel injection volume measurement has a margin of error, the value is indicated after correction by input values from the fuel sender gauge assembly and No. 2 fuel sender gauge assembly*1.


b.

During refueling:

The fuel level in the fuel tank assembly rises rapidly when fuel is added. If the averaging process that is used during normal driving is used in this case, the fuel receiver gauge reading cannot be updated promptly. Therefore, when it is judged that fuel is being added to the vehicle based on the shift lever position and changes in the fuel level, output values from the fuel sender gauge assembly and No. 2 fuel sender gauge assembly*1 are immediately reflected in the fuel receiver gauge reading. This control is called refueling judgment.



*1: for AWD


REFUELING JUDGMENT CONDITIONS


NOTICE:

Add fuel with the ignition switch off to ensure safety and to enable refueling judgment so that an appropriate fuel receiver gauge reading is obtained. If it is necessary to add fuel with the ignition switch ON move the shift lever to P or N.


a.

Normal judgment condition (When normal refueling method is used)

With the ignition switch off, the fuel sender gauge assembly and No. 2 fuel sender gauge assembly*1 detect a change of 5.0 liters (5.3 US qts, 4.4 Imp. qts) or more in the fuel level.


b.

Other judgment conditions (When other refueling method is used)

Any of the following conditions is met:

·

With the vehicle and engine stopped and the ignition switch ON the fuel sender gauge assembly and No. 2 fuel sender gauge assembly*1 detect a change of 5.0 liters (5.3 US qts, 4.4 Imp. qts) or more in the fuel level.

·

With the vehicle stopped, the engine running, the ignition switch ON and the shift lever in P or N, the fuel sender gauge assembly and No. 2 fuel sender gauge assembly*1 detect a change of 5.0 liters (5.3 US qts, 4.4 Imp. qts) or more in the fuel level.

·

With the vehicle stopped, the engine running, the ignition switch ON and the shift lever in any driving position, the fuel sender gauge assembly and No. 2 fuel sender gauge assembly*1 detect a change of 15.0 liters (15.9 US qts, 13.2 Imp. qts) or more in the fuel level.




*1: for AWD


PRECAUTION FOR REFUELING


The fuel sender gauge assembly and No. 2 fuel sender gauge assembly*1 cannot detect changes in the fuel level within certain ranges (around points E and F). Therefore, even if 5.0 liters (5.3 US qts, 4.4 Imp. qts) or more of fuel is added, refueling judgment may not be performed and the fuel receiver gauge reading may not change when fuel level is within such ranges.


*1: for AWD


FORCED RESET OF FUEL RECEIVER GAUGE


When driving at 1.8 km/h (1 mph) or more, if the output values from the fuel sender gauge assembly and No. 2 fuel sender gauge assembly*1 are different from the fuel receiver gauge reading by 15.0 liters (15.9 US qts, 13.2 Imp. qts) or more for approximately 2 minutes, output values from both gauge assemblies are immediately reflected in the fuel receiver gauge reading to compensate for a situation when refueling judgment cannot be made.


*1: for AWD


WIRING DIAGRAM

C360597E04
5.5,1.802 6.052,1.313 true 1.333,0.719 2.552,1.083 1.219,0.365 10 false Fuel Sender Gauge Assembly 2.635,0.542 2.792,0.74 0.156,0.198 10 false 1 3,0.708 3.156,0.906 0.156,0.198 10 false 3 2.635,1.083 2.792,1.281 0.156,0.198 10 false 2 3.573,0.698 3.729,0.896 0.156,0.198 10 false 1 3.573,0.323 3.729,0.521 0.156,0.198 10 false 3 3.573,1.073 3.729,1.271 0.156,0.198 10 false 2 3.281,0.323 3.594,0.521 0.313,0.198 10 false FR 3.281,0.698 3.594,0.896 0.313,0.198 10 false FV 3.281,1.073 3.594,1.271 0.313,0.198 10 false FE 1.073,1.49 1.542,1.667 0.469,0.177 10 false M14*1 1.073,1.667 3.583,2.052 2.51,0.385 10 false Fuel Suction Tube with Pump and Gauge Assembly 4.927,0.323 5.24,0.521 0.313,0.198 10 false FR 4.927,0.708 5.24,0.906 0.313,0.198 10 false FV 4.927,1.083 5.396,1.292 0.469,0.208 10 false FR2*2 4.677,0.323 4.99,0.521 0.313,0.198 10 false 23 4.677,0.708 4.99,0.906 0.313,0.198 10 false 16 4.677,1.083 4.99,1.281 0.313,0.198 10 false 22 5.458,0.438 5.917,0.635 0.458,0.198 10 false I/F 5.458,0.813 5.917,1.01 0.458,0.198 10 false I/F 5.458,1.198 5.917,1.396 0.458,0.198 10 false I/F 6.021,2.135 6.479,2.333 0.458,0.198 10 false CPU 4.677,3.26 4.99,3.458 0.313,0.198 10 false 15 4.677,3.781 4.99,3.979 0.313,0.198 10 false 21 4.927,3.26 5.542,3.458 0.615,0.198 10 false EE&B 4.927,3.781 5.24,3.979 0.313,0.198 10 false ET 4.875,4.438 6.813,4.667 1.938,0.229 10 false Combination Meter Assembly 4.958,1.823 5.906,2.01 0.948,0.188 10 false Fuel Controller 4.885,4.271 5.198,4.469 0.313,0.198 10 false F4 3.833,2.51 4.146,2.708 0.313,0.198 10 false *2 3.573,2.51 3.729,2.708 0.156,0.198 10 false 1 3.833,2.885 4.146,3.083 0.313,0.198 10 false *2 3.833,3.26 4.146,3.458 0.313,0.198 10 false *2 3.573,2.885 3.729,3.083 0.156,0.198 10 false 3 3.573,3.26 3.729,3.458 0.156,0.198 10 false 2 3.281,2.521 3.594,2.719 0.313,0.198 10 false FV 3.281,2.885 3.594,3.083 0.313,0.198 10 false FR 3.281,3.26 3.594,3.458 0.313,0.198 10 false FE 3,2.885 3.156,3.083 0.156,0.198 10 false 1 2.635,2.74 2.792,2.938 0.156,0.198 10 false 3 2.635,3.271 2.792,3.469 0.156,0.198 10 false 2 1.385,2.896 2.531,3.271 1.146,0.375 10 false No. 2 Fuel Sender Gauge Assembly 1.073,3.698 1.531,3.896 0.458,0.198 10 false M76 1.073,3.875 3.552,4.271 2.479,0.396 10 false No. 2 Fuel Suction Tube with Pump and Gauge Assembly*2 0.167,4.417 1.021,4.625 0.854,0.208 10 false *1: for 2WD 1.156,4.406 1.99,4.583 0.833,0.177 10 false *2: for AWD 1.542,1.49 2.021,1.688 0.479,0.198 10 false M75*2

CAUTION / NOTICE / HINT

NOTICE:

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.


HINT:

The fuel level warning light will come on when the fuel level is below 9.96 liters (10.5 US qts, 8.8 Imp. qts).


PROCEDURE

1.CHECK SYMPTOMS
a.

Ask the customer about the problem symptoms.


Result:
Result Proceed to
Malfunction occurs when adding fuel (Even after adding fuel, reading does not increase at all or increases very slowly, etc.) A
Malfunction occurs during normal driving (The reading does not change, decreases quickly or decreases when the vehicle is not being driven, etc.) (The problem symptom recurs) B
Malfunction occurs during normal driving (The reading does not change, decreases quickly or decreases when the vehicle is not being driven, etc.) (The problem symptom does not recur) C



A

2.CHECK FOR DTC

B

12.CHECK FOR DTC

C

16.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check if SFI system DTCs are output. (for 8NR-FTS)

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Trouble Codes
50001 234

b.

Check if SFI system DTCs are output. (for 3ZR-FAE)

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Result Proceed to
SFI system DTCs are not output. A
SFI system DTCs are output. (for 3ZR-FAE) B
SFI system DTCs are output. (for 8NR-FTS) C



A

3.CHECK FOR DTC

B

C

3.CHECK FOR DTC
a.

Check if vehicle stability control system DTCs are output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC/EPB > Trouble Codes
50001 105

Result:
Result Proceed to
Vehicle stability control system DTCs are not output. A
Vehicle stability control system DTCs are output. B



A

4.CHECK FUEL RECEIVER GAUGE OPERATION BY ADDING FUEL

B

4.CHECK FUEL RECEIVER GAUGE OPERATION BY ADDING FUEL
a.

Record the fuel receiver gauge reading.


b.

If the fuel tank assembly is almost full, drain 20 liters or more of fuel. (This is not necessary when the fuel tank assembly is sufficiently below full.)


c.

Disconnect the cable from the negative (-) battery terminal to reset the fuel receiver gauge.

HINT:

Check that the ignition switch is turned off before disconnecting the cable from the negative (-) battery terminal.



d.

Connect the cable to the negative (-) battery terminal and turn the ignition switch ON.


e.

Check that the fuel receiver gauge has been reset.


f.

Drive the vehicle at 1.75 km/h or more, then move the shift lever to P and turn the ignition switch off.


g.

Add 5.0 liters or more of fuel, turn the ignition switch ON and check that the fuel receiver gauge reading increases in proportion to the amount of fuel added.


Result:
Result Proceed to
Fuel receiver gauge reading increases in proportion to the amount of fuel added A
Fuel receiver gauge reading does not change even when fuel is added B



A

5.INSPECT FUEL TANK ASSEMBLY

B

6.READ VALUE USING GTS (FUEL INPUT)
5.INSPECT FUEL TANK ASSEMBLY
HINT:

Inspect the fuel tank assembly for deformation, foreign matter or an improperly installed fuel receiver gauge, as this may be the cause of the fuel receiver gauge malfunction.


a.

Visually check the fuel tank assembly for any abnormalities.


b.

Check if there is an excessive amount of foreign matter in the fuel tank assembly.


c.

Check the installation condition of the fuel tank assembly, fuel sender gauge assembly and No. 2 fuel sender gauge assembly*1.

*1: for AWD



Result:
Result Proceed to
Normal A
Appearance of the fuel tank assembly is abnormal. (for 8NR-FTS with 2WD) B
Appearance of the fuel tank assembly is abnormal. (for 8NR-FTS with AWD) C
Appearance of the fuel tank assembly is abnormal. (for 3ZR-FAE) D
There is an excessive amount of foreign matter in the fuel tank assembly. E
The fuel tank assembly, fuel sender gauge assembly or No. 2 fuel sender gauge assembly is not installed correctly. (for AWD) F



A

6.READ VALUE USING GTS (FUEL INPUT)

B

C

D

REPLACE FUEL TANK ASSEMBLY

E

CLEAN INSIDE OF FUEL TANK ASSEMBLY

F

INSTALL FUEL TANK ASSEMBLY, FUEL SENDER GAUGE ASSEMBLY OR NO. 2 FUEL SENDER GAUGE ASSEMBLY CORRECTLY

6.READ VALUE USING GTS (FUEL INPUT)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch ON.


c.

Turn the GTS on.


d.

Enter following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Fuel Input Fuel input Min.: 0 L, Max.: 127.5 L
·

Fuel receiver gauge indicates

F (for 8NR-FTS with 2WD): 43.8 L

F (for 8NR-FTS with AWD): 45.0 L

F (for 3ZR-FAE): 44.0 L

·

Fuel receiver gauge indicates

3/4 (for 8NR-FTS with 2WD): 34.5 L

3/4 (for 8NR-FTS with AWD): 36.0 L

3/4 (for 3ZR-FAE): 34.6 L

·

Fuel receiver gauge indicates

1/2 (for 8NR-FTS with 2WD): 24.4 L

1/2 (for 8NR-FTS with AWD): 26.1 L

1/2 (for 3ZR-FAE): 24.5 L

·

Fuel receiver gauge indicates

1/4 (for 8NR-FTS with 2WD): 14.3 L

1/4 (for 8NR-FTS with AWD): 14.1 L

1/4 (for 3ZR-FAE): 14.4 L

·

Fuel receiver gauge indicates

E (for 8NR-FTS with 2WD): 5.0 L

E (for 8NR-FTS with AWD): 5.0 L

E (for 3ZR-FAE): 5.0 L


Unit :Liter
Body Electrical > Combination Meter > Data List
Tester Display
Fuel Input
50003 122 39

Result:
Result Proceed to
Fuel level data displayed on the GTS is almost the same as the fuel receiver gauge indication. A
Fuel level data displayed on the GTS differs from the fuel receiver gauge indication. B



A

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY, NO. 2 FUEL SUCTION TUBE WITH PUMP AND GAUGE)

B

REPLACE COMBINATION METER ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY, NO. 2 FUEL SUCTION TUBE WITH PUMP AND GAUGE)
a.

Disconnect the F4 combination meter assembly connector.


b.

Disconnect the M14*1 or M75*2 fuel suction tube with pump and gauge assembly connector.


c.

Disconnect the M76 No. 2 fuel suction tube with pump and gauge assembly connector.*2


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M14-1 (FV) - F4-16 (FV)*1 Always Below 1 Ω
M14-2 (FE) - F4-15 (EE&B)*1 Always Below 1 Ω
M14-3 (FR) - F4-23 (FR)*1 Always Below 1 Ω
M14-1 (FV) - Body ground*1 Always 10 kΩ or higher
M14-2 (FE) - Body ground*1 Always 10 kΩ or higher
M14-3 (FR) - Body ground*1 Always 10 kΩ or higher
M75-1 (FV) - F4-16 (FV)*2 Always Below 1 Ω
M75-2 (FE) - F4-15 (EE&B)*2 Always Below 1 Ω
M75-3 (FR) - F4-23 (FR)*2 Always Below 1 Ω
M75-1 (FV) - Body ground*2 Always 10 kΩ or higher
M75-2 (FE) - Body ground*2 Always 10 kΩ or higher
M75-3 (FR) - Body ground*2 Always 10 kΩ or higher
M76-1 (FV) - F4-16 (FV)*2 Always Below 1 Ω
M76-2 (FE) - F4-15 (EE&B)*2 Always Below 1 Ω
M76-3 (FR) - F4-22 (FR2)*2 Always Below 1 Ω
M76-1 (FV) - Body ground*2 Always 10 kΩ or higher
M76-2 (FE) - Body ground*2 Always 10 kΩ or higher
M76-3 (FR) - Body ground*2 Always 10 kΩ or higher


*1: for 2WD

*2: for AWD



Result:
Proceed to
OK
NG



OK

8.INSPECT FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY
a.

Remove the fuel suction plate sub-assembly.



b.
E158805C61
0.313,1.333 0.74,1.635 0.427,0.302 0.313,3.667 0.729,3.958 0.417,0.292 1.385,1.208 1.083,0.75 true 1.74,1.219 2,0.667 true 2.083,1.229 2.5,0.917 true 0.125,0.188 1.563,0.354 1.438,0.167 10 false *a 0.5,1.417 0.833,1.667 0.333,0.25 10 false A 0.5,3.74 0.833,3.99 0.333,0.25 10 false B 2.063,0.5 2.396,0.75 0.333,0.25 10 false FE 0.854,0.594 1.188,0.844 0.333,0.25 10 false FR 2.563,0.771 2.896,1.021 0.333,0.25 10 false FV
*a Component without harness connected
(Fuel Suction Tube with Pump and Gauge Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-1 (FV) - B-3 Always Below 1 Ω
A-2 (FE) - B-2 Always Below 1 Ω
A-3 (FR) - B-1 Always Below 1 Ω



Result:
Result Proceed to
OK A
NG (for 8NR-FTS with 2WD) B
NG (for 8NR-FTS with AWD) C
NG (for 3ZR-FAE) D



A

9.INSPECT FUEL SENDER GAUGE ASSEMBLY

B

REPLACE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

C

REPLACE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

D

REPLACE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

9.INSPECT FUEL SENDER GAUGE ASSEMBLY


Result:
Result Proceed to
OK A
NG (for 8NR-FTS with AWD) B
NG (for 8NR-FTS with 2WD) C
NG (for 3ZR-FAE) D



A

REPLACE COMBINATION METER ASSEMBLY

B

10.INSPECT NO. 2 FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

C

D

10.INSPECT NO. 2 FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY
a.

Remove the No. 2 fuel suction tube with pump and gauge assembly.

Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL SENDER GAUGE ASSEMBLY (for AWD)>REMOVAL


b.
E158805C63
0.313,1.333 0.74,1.635 0.427,0.302 0.313,3.667 0.729,3.958 0.417,0.292 1.385,1.208 1.083,0.75 true 1.74,1.219 2,0.667 true 2.083,1.229 2.5,0.917 true 0.125,0.188 1.563,0.354 1.438,0.167 10 false *a 0.5,1.417 0.833,1.667 0.333,0.25 10 false A 0.5,3.74 0.833,3.99 0.333,0.25 10 false B 2.063,0.5 2.396,0.75 0.333,0.25 10 false FE 0.854,0.594 1.188,0.844 0.333,0.25 10 false FR 2.563,0.771 2.896,1.021 0.333,0.25 10 false FV
*a Component without harness connected
(No. 2 Fuel Suction Tube with Pump and Gauge Assembly )


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-1 (FV) - B-3 Always Below 1 Ω
A-2 (FE) - B-2 Always Below 1 Ω
A-3 (FR) - B-1 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

11.INSPECT NO. 2 FUEL SENDER GAUGE ASSEMBLY

NG

11.INSPECT NO. 2 FUEL SENDER GAUGE ASSEMBLY
a.

Remove the No. 2 fuel sender gauge assembly.

Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL SENDER GAUGE ASSEMBLY (for AWD)>REMOVAL


b.

Inspect the No. 2 fuel sender gauge assembly.

Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL SENDER GAUGE ASSEMBLY (for AWD)>INSPECTION


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

12.CHECK FOR DTC
a.

Check if SFI system DTCs are output. (for 8NR-FTS)

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Trouble Codes
50001 234

b.

Check if SFI system DTCs are output. (for 3ZR-FAE)

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Result Proceed to
SFI system DTCs are not output. A
SFI system DTCs are output. (for 8NR-FTS) B
SFI system DTCs are output. (for 3ZR-FAE) C



A

13.CHECK FOR DTC

B

C

13.CHECK FOR DTC
a.

Check if vehicle stability control system DTCs are output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC/EPB > Trouble Codes
50001 105

Result:
Result Proceed to
Vehicle stability control system DTCs are not output. A
Vehicle stability control system DTCs are output. B



A

14.CHECK FOR DTC

B

14.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR

Body Electrical > Combination Meter > Trouble Codes
50001 122

Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

15.INSPECT FUEL RECEIVER GAUGE

B

15.INSPECT FUEL RECEIVER GAUGE
a.

Disconnect the cable from the negative (-) battery terminal to reset the fuel receiver gauge.

HINT:

Check that the ignition switch is turned off before disconnecting the cable from the negative (-) battery terminal.



b.

Connect the cable to the negative (-) battery terminal and turn the ignition switch ON.


c.

Check if the fuel receiver gauge reading corresponds with the amount of fuel remaining in the fuel tank assembly.


Result:
Result Proceed to
Fuel receiver gauge reading corresponds with the amount of fuel remaining in the fuel tank assembly. A
Fuel receiver gauge reading does not correspond with the amount of fuel remaining in the fuel tank assembly. B



A

END

B

6.READ VALUE USING GTS (FUEL INPUT)
16.CHECK FOR DTC
a.

Check if SFI system DTCs are output. (for 8NR-FTS)

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Trouble Codes
50001 234

b.

Check if SFI system DTCs are output. (for 3ZR-FAE)

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Result Proceed to
SFI system DTCs are not output. A
SFI system DTCs are output. (for 8NR-FTS) B
SFI system DTCs are output. (for 3ZR-FAE) C



A

17.CHECK FOR DTC

B

C

17.CHECK FOR DTC
a.

Check if vehicle stability control system DTCs are output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC/EPB > Trouble Codes
50001 105

Result:
Result Proceed to
Vehicle stability control system DTCs are not output. A
Vehicle stability control system DTCs are output. B



A

18.INSPECT FUEL TANK ASSEMBLY

B

18.INSPECT FUEL TANK ASSEMBLY
HINT:

Inspect the fuel tank assembly for deformation, foreign matter or an improperly installed fuel receiver gauge, as this may be the cause of the fuel receiver gauge malfunction.


a.

Visually check the fuel tank assembly for any abnormalities.


b.

Check if there is an excessive amount of foreign matter in the fuel tank assembly.


c.

Check the installation condition of the fuel tank assembly, fuel sender gauge assembly and No. 2 fuel sender gauge assembly.


Result:
Result Proceed to
Normal A
Appearance of the fuel tank assembly is abnormal. (for 8NR-FTS with 2WD) B
Appearance of the fuel tank assembly is abnormal. (for 8NR-FTS with AWD) C
Appearance of the fuel tank assembly is abnormal. (for 3ZR-FAE) D
There is an excessive amount of foreign matter in the fuel tank assembly. E
The fuel tank assembly, fuel sender gauge assembly or No. 2 fuel sender gauge assembly is not installed correctly. F



A

REPLACE COMBINATION METER ASSEMBLY

B

C

D

REPLACE FUEL TANK ASSEMBLY

E

CLEAN INSIDE OF FUEL TANK ASSEMBLY

F

INSTALL FUEL TANK ASSEMBLY, FUEL SENDER GAUGE ASSEMBLY OR NO. 2 FUEL SENDER GAUGE ASSEMBLY CORRECTLY